Noble House 22681 Operating instructions

Brand
Noble House
Model
22681
Type
Operating instructions
NO. Picture QTY
A 1
B 2
C 1
①
11
②
11
③
1
Assembly instructions
Caution: You must read this before you proceed
BENCH
CAUTION: This bench is NOT a TOY.
Keep your child / children at bay in the process of assembly.
Allen Wrench(8mm)
Parts list
Description
Bench Seat
Leg with pre-attached Levellers
Hard ware
Studs(M8*16)
Washers(8mm)
Leg Support
Noble House Home Furnishings LLC
1 OF 5
Assembly Step
This Bench has multiple parts and may require up to some 30 minutes to
assemble.
To give you an overview of the Bench parts, the above picture is to help you
put the various parts into perspective.
Please read through the instructions below to familiarise yourself with the
parts and steps before assembly.
Assembly Preparation
Before Beginning Assembly:
Overview
Bench Seat(A)
FRONT FACING
pre-attached
Leveller(B)
Leg Support (C)
Noble House Home Furnishings LLC
2 OF 5
Unpack and place all parts onto a clean soft surface.
Attach Leg with pre-attached Levellers(B) and Leg Support(C) with Bolts(①)
and Washers(②) by Allen Wrench(③).
DO NOT OVERTIGHTEN.
B
③
①
C
A
Noble House Home Furnishings LLC
3 OF 5
Turn the Bench rightside up.
Adjust the pre-installed Leveller until the Bench is level with the ground.
Then, proceed to tighten all Bolts and Nuts.
Your Bench is ready for use.
Caution: This Bench can only be used on a flat, level surface.
Turn the Bench Seat(A) upside down on to a soft surface to avoid
scratching.
Attach Leg with Pre-attached Levellers(B) to the mounting position on the
Bench Seat(A) with Bolts(①), Washers(②) by Allen Wrench(③).
DO NOT OVERTIGHTEN.
Adjust height
for balance
Adjust low
for balance
Noble House Home Furnishings LLC
4 OF 5
Noble House Home Furnishings LLC
5 OF 5
NO. Picture QTY
A 1
B 2
C 1
Assembly instructions
Caution : You must read this before you proceed
TABLE
CAUTION: This table is NOT a TOY.
Keep your child / children at bay in the process of assembly.
Parts list
Leg Support
Description
Table Top
Leg with pre-attached Levellers
Noble House Home Furnishings LLC
1 OF 5
①
19
②
19
③
1
Washer(8mm)
Assembly Preparation
Before Beginning Assembly:
Hardware
Bolt(M8*16)
Allen Wrench(8mm)
Assembly Step
This Table has multiple parts and may require up to some 30 minutes to
assemble.
To give you an overview of the Table parts, the above picture is to help you
put the various parts into perspective.
Please read through the instructions below to familiarise yourself with the
parts and steps before assembly.
Overview
Table Top(A)
FRONT FACING
Leg with pre-
attached Leveller(B)
Leg Support (C)
Noble House Home Furnishings LLC
2 OF 5
Unpack and place all parts onto a clean soft surface.
Attach Leg with pre-attached Levellers(B) and Leg Support(C) with Bolts(①)
and Washers(②) by Allen Wrench(③).
DO NOT OVERTIGHTEN.
③
②
①
C
B
Noble House Home Furnishings LLC
3 OF 5
Turn the table top upside down to a soft surface to avoid scratching.
Attach Table Leg with Pre-attached Levellers(B) to the mounting position on
the table top(A) with Bolts(①), Washers(②) by Allen Wrench(③).
DO NOT OVERTIGHTEN.
Turn the Table rightside up.
Adjust the pre-installed Leveller until the Table is level with the ground.
Then, proceed to tighten all Bolts and Nuts.
Your table is ready for use.
Caution: This Table can only be used on a flat, level surface.
Adjust height
for balance
Adjust low
for balance
Noble House Home Furnishings LLC
4 OF 5
Noble House Home Furnishings LLC
5 OF 5
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

Noble House 22681 Operating instructions

Brand
Noble House
Model
22681
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents