Moen TS42114BN-9000-L Dimensions Guide

Category
Sanitary ware
Type
Dimensions Guide
WEYMOUTH™
Two-Handle Widespread Lavatory Faucet
Models: TS42114 series (cross handle)
TS42108 series (lever handle)
Valves: 9000, 69000
NOTE: THIS FAUCET IS DESIGNED TO BE
INSTALLED THRU 3 HOLES, 11/8” MIN. DIA.
NOTE: FOR DECK THICKNESS 1-1/2” to 3”, USE SERVICE KIT
#175709. VALVES INSTALL THROUGH 1-1/4” DIA. HOLE.
3”
(76mm)
4”
(101mm)
4”
(101mm)
8” (203mm) - 16” (406mm)
CENTERS
COLD
INLET
HOT
INLET
2-1/2”
(64mm)
2”
(51mm)
1-1/4” (32mm)
MAX. DECK THICKNESS
5-3/4”
(146mm)
7-1/2”
(190mm)
5-1/4”
(133mm)
1-1/2”
(38mm)
Rev. 2/16
DESCRIPTION
Duralock™ quick connect installation
Metal construction with various finishes identified by suffix
1/2” IPS connections
Includes metal pop-up waste assembly
OPERATION
Cross and lever style handles
Maximum handle rotation angle is 90˚ to full on for either handle
Hot side counterclockwise to open (clockwise to close)
Cold side clockwise to open (counterclockwise to close)
FLOW
Water usage is limited to these maximum flow rates as indicated by the
corresponding product markings
° 1.2 gpm max (4.5L/min) at 60 ps
° 1.5 gpm max (5.7L/min) at 60 ps
CARTRIDGE
1234™ Duralast™ cartridge
Nonmetallic, nonferrous and stainless steel material
STANDARDS
Third party certified to WaterSense,® ASME A112.18.1/CSA B125.1, and
all applicable requirements referenced therein
Certified to NSF 61/9 & 372
Products marked with 1.2 gpm are compliant with California water
efficiency regulations
Complies with California Proposition 65 and with the Federal Safe
Drinking Water Act
ADA for lever handles
WARRANTY
Lifetime limited warranty against leaks, drips and finish
defects to the original consumer purchaser
5 year warranty if used in commercial installations
CRITICAL DIMENSIONS
(DO NOT SCALE)
Spec i fi ca tions
FOR MORE INFORMATION CALL: 1-800-BUY-MOEN
www.moen.com
There is more than 1 version of this model.
Page down to identify the version you have.
WEYMOUTH™
Two-Handle Widespread Lavatory Faucet
Models: TS42114 series (cross handle)
TS42108 series (lever handle)
Valves: 9000, 69000
NOTE: THIS FAUCET IS DESIGNED TO BE
INSTALLED THRU 3 HOLES, 11/8” MIN. DIA.
NOTE: FOR DECK THICKNESS 1-1/2” to 3”, USE SERVICE KIT
#115001. VALVES INSTALL THROUGH 1-1/4” DIA. HOLE.
3”
(76mm)
4”
(101mm)
4”
(101mm)
8” (203mm) - 16” (406mm)
CENTERS
COLD
INLET
HOT
INLET
2-1/2”
(64mm)
2”
(51mm)
1-1/4” (32mm)
MAX. DECK THICKNESS
5-3/4”
(146mm)
7-1/2”
(190mm)
5-1/4”
(133mm)
1-1/2”
(38mm)
Rev. 8/15
DESCRIPTION
Quick connect installation
Metal construction with various finishes identified by suffix
1/2” IPS connections
Includes metal pop-up waste assembly
OPERATION
Cross and lever style handles
Maximum handle rotation angle is 90˚ to full on for either handle
Hot side counterclockwise to open (clockwise to close)
Cold side clockwise to open (counterclockwise to close)
FLOW
Flow is limited to 1.5 gpm max (5.7L/min) at 60 psi
CARTRIDGE
1224 cartridge design
Nonmetallic and stainless steel material
STANDARDS
Third party certified to WaterSense®, ASME A112.18.1/CSA B125.1, and
all applicable requirements referenced therein including NSF61/9 & 372
Complies with California Proposition 65 and with the Federal Safe
Drinking Water Act
ADA for lever handles
WARRANTY
Lifetime limited warranty against leaks, drips and finish
defects to the original consumer purchaser
5 year warranty if used in commercial installations
CRITICAL DIMENSIONS
(DO NOT SCALE)
Spec i fi ca tions
FOR MORE INFORMATION CALL: 1-800-BUY-MOEN
www.moen.com
  • Page 1 1
  • Page 2 2

Moen TS42114BN-9000-L Dimensions Guide

Category
Sanitary ware
Type
Dimensions Guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI