RAB Lighting GDWP2W Operating instructions

GDWP2W
RAB Lighting
Brand
RAB Lighting
Model
GDWP2W
Type
Operating instructions

This manual is also suitable for

GDWPLED2P Poly Shield
Thank you for buying RAB lighting xtures. Our goal is to design the best
quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000, or email: marketing@
rabweb.com
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE
INSTRUCTIONS FOR FUTURE REFERENCE.
RAB xtures must be wired in accordance with the National
Electrical Code and all applicable local codes. Proper grounding
is required for safety. This product must be installed in
accordance with the applicable installation code by a person
familiar with the construction and operation of the product and the
hazards involved.
WARNING: Make certain power is OFF before installing or
maintaining xture.
GDWPLED2P Poly Shield
Thank you for buying RAB lighting xtures. Our goal is to design the best
quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000, or email: marketing@
rabweb.com
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE
INSTRUCTIONS FOR FUTURE REFERENCE.
RAB xtures must be wired in accordance with the National
Electrical Code and all applicable local codes. Proper grounding
is required for safety. This product must be installed in
accordance with the applicable installation code by a person
familiar with the construction and operation of the product and the
hazards involved.
WARNING: Make certain power is OFF before installing or
maintaining xture.
CLEANING
Clean glass lens with nonabrasive glass cleaning solution.
CAUTION: Be surexture temperature is cool enough to
touch. Do not clean or maintain while xture is energized.
Installation
1. Remove existing door
2. Re-mount door with Poly
Shield already installed to
housing
3. Tighten four Lens Screws
4. Check that door gasket is
fully sealed
CLEANING
Clean glass lens with nonabrasive glass cleaning solution.
CAUTION: Be surexture temperature is cool enough to
touch. Do not clean or maintain while xture is energized.
Note: These instructions do not cover all details or variations in equipment
nor do they provide for every possible situation during installation, operation
or maintenance.
®
®
Installation
1. Remove existing door
2. Re-mount door with Poly
Shield already installed to
housing
3. Tighten four Lens Screws
4. Check that door gasket is
fully sealed
GDWPLED2P-IN-0710 GDWPLED2P-IN-0710
(4) Lens Screws
(4) Lens Screws
Note: These instructions do not cover all details or variations in equipment
nor do they provide for every possible situation during installation, operation
or maintenance.
GDSLIM37P POLY SHIELD
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the
job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000,
or email: marketing@rabweb.com
SLIM35 POLYSHIELD
RAB LIGHTING
3/22/2013
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS
FOR FUTURE REFERENCE.
RAB xtures must be wired in accordance with the National Electrical Code
and all applicable local codes. Proper grounding is required for safety. This
product must be installed in accordance with the applicable installation code
by a person familiar with the construction and operation of the product and
the hazards involved.
WARNING: Make certain power is OFF before installing or maintaining xture.
CLEANING
Clean glass lens with nonabrasive glass cleaning solution.
CAUTION: Be sure xture temperature is cool enough to touch. Do not
clean or maintain while xture is energized.
GDSLIM37P IN 0713
INSTALLATION
Poly Shield mounts with (4) #8-32 x 1/2” stainless steel Screws to frame as
shown. Hardware is provided with shield. Guard and shield may be used
together.
1. Remove left and right Cover Plates and discard.
2. Line up shield with existing pre-drilled holes in frame as shown, tighten
screws.
Screws (4)
Note: These instructions do not cover all details or variations in equipment nor do
they provide for every possible situation during installation, operation or maintenance.
Polyshield
Housing
Easy Installation & Product Help
Tech Help Line
Call our experts 888 RAB-1000
©2013 RAB LIGHTING Inc.
Northvale, New Jersey 07647 USA
rabweb.com
Visit our website for product info
email
Answered promptly sales@rabweb.com
Screws
Cover Plate
GDSLIM37W WIRE GUARD
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the
job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000,
or email: marketing@rabweb.com
SLIM35 WIRE GAURD
RAB LIGHTING
3/22/2013
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS
FOR FUTURE REFERENCE.
RAB xtures must be wired in accordance with the National Electrical Code
and all applicable local codes. Proper grounding is required for safety. This
product must be installed in accordance with the applicable installation code
by a person familiar with the construction and operation of the product and
the hazards involved.
WARNING: Make certain power is OFF before installing or maintaining xture.
CLEANING
Clean glass lens with nonabrasive glass cleaning solution.
CAUTION: Be sure xture temperature is cool enough to touch. Do not
clean or maintain while xture is energized.
GDSLIM37W IN 0713
INSTALLATION
Wire Guard mounts with (4) #8-32 x 1/2” stainless steel Screws to frame as
shown. Hardware is provided with guard. Guard and shield may be used
together.
1. Remove left and right Cover Plates and discard.
2. Line up guard with existing pre-drilled holes in frame as shown, tighten
screws.
Screws (4)
Note: These instructions do not cover all details or variations in equipment nor do
they provide for every possible situation during installation, operation or maintenance.
Wire Guard
Housing
Easy Installation & Product Help
Tech Help Line
Call our experts 888 RAB-1000
©2013 RAB LIGHTING Inc.
Northvale, New Jersey 07647 USA
rabweb.com
Visit our website for product info
email
Answered promptly sales@rabweb.com
Screws
Cover Plate
GDSLIM57P POLY SHIELD
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the
job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000,
or email: marketing@rabweb.com
SLIM47 POLYSHIELD
RAB LIGHTING
3/22/2013
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS
FOR FUTURE REFERENCE.
RAB xtures must be wired in accordance with the National Electrical Code
and all applicable local codes. Proper grounding is required for safety. This
product must be installed in accordance with the applicable installation code
by a person familiar with the construction and operation of the product and
the hazards involved.
WARNING: Make certain power is OFF before installing or maintaining xture.
CLEANING
Clean glass lens with nonabrasive glass cleaning solution.
CAUTION: Be sure xture temperature is cool enough to touch. Do not
clean or maintain while xture is energized.
GDSLIM57P IN 0713
INSTALLATION
Poly Shield mounts with (4) #8-32 x 1/2” stainless steel Screws to frame as
shown. Hardware is provided with shield. Guard and shield may be used
together.
1. Remove left and right Cover Plates and discard.
2. Line up shield with existing pre-drilled holes in frame as shown, tighten
screws.
Screws (4)
Note: These instructions do not cover all details or variations in equipment nor do
they provide for every possible situation during installation, operation or maintenance.
Poly Shield
Housing
Easy Installation & Product Help
Tech Help Line
Call our experts 888 RAB-1000
©2013 RAB LIGHTING Inc.
Northvale, New Jersey 07647 USA
rabweb.com
Visit our website for product info
email
Answered promptly sales@rabweb.com
Screws
Cover Plate
GDSLIM57W WIRE GUARD
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the
job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000,
or email: marketing@rabweb.com
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS
FOR FUTURE REFERENCE.
RAB xtures must be wired in accordance with the National Electrical Code
and all applicable local codes. Proper grounding is required for safety. This
product must be installed in accordance with the applicable installation code
by a person familiar with the construction and operation of the product and
the hazards involved.
WARNING: Make certain power is OFF before installing or maintaining xture.
CLEANING
Clean glass lens with nonabrasive glass cleaning solution.
CAUTION: Be sure xture temperature is cool enough to touch. Do not
clean or maintain while xture is energized.
GDSLIM57W IN 0713
INSTALLATION
Wire Guard mounts with (4) #8-32 x 1/2” stainless steel Screws to frame as
shown. Hardware is provided with guard. Guard and shield may be used
together.
1. Remove left and right Cover Plates and discard.
2. Line up guard with existing pre-drilled holes in frame as shown, tighten
screws.
Screws (4)
Note: These instructions do not cover all details or variations in equipment nor do
they provide for every possible situation during installation, operation or maintenance.
Wire Guard
Housing
Easy Installation & Product Help
Tech Help Line
Call our experts 888 RAB-1000
©2013 RAB LIGHTING Inc.
Northvale, New Jersey 07647 USA
rabweb.com
Visit our website for product info
email
Answered promptly sales@rabweb.com
Screws
Cover Plate
SLIM47 WIRE GAURD
RAB LIGHTING
3/22/2013
GDSLIM62P POLY SHIELD
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the
job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000,
or email: marketing@rabweb.com
SLIM56 POLYSHIELD
RAB LIGHTING
3/22/2013
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS
FOR FUTURE REFERENCE.
RAB xtures must be wired in accordance with the National Electrical Code
and all applicable local codes. Proper grounding is required for safety. This
product must be installed in accordance with the applicable installation code
by a person familiar with the construction and operation of the product and
the hazards involved.
WARNING: Make certain power is OFF before installing or maintaining xture.
CLEANING
Clean glass lens with nonabrasive glass cleaning solution.
CAUTION: Be sure xture temperature is cool enough to touch. Do not
clean or maintain while xture is energized.
GDSLIM62P IN 0713
INSTALLATION
Poly Shield mounts with (4) #8-32 x 1/2” stainless steel Screws to frame as
shown. Hardware is provided with shield. Guard and shield may be used
together.
1. Remove left and right Cover Plates and discard.
2. Line up shield with existing pre-drilled holes in frame as shown, tighten
screws.
Screws (4)
Note: These instructions do not cover all details or variations in equipment nor do
they provide for every possible situation during installation, operation or maintenance.
Poly Shield
Housing
Easy Installation & Product Help
Tech Help Line
Call our experts 888 RAB-1000
©2013 RAB LIGHTING Inc.
Northvale, New Jersey 07647 USA
rabweb.com
Visit our website for product info
email
Answered promptly sales@rabweb.com
Screws
Cover Plate
GDSLIM62W WIRE GUARD
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the
job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000,
or email: marketing@rabweb.com
SLIM56 WIRE GAURD
RAB LIGHTING
3/22/2013
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS
FOR FUTURE REFERENCE.
RAB xtures must be wired in accordance with the National Electrical Code
and all applicable local codes. Proper grounding is required for safety. This
product must be installed in accordance with the applicable installation code
by a person familiar with the construction and operation of the product and
the hazards involved.
WARNING: Make certain power is OFF before installing or maintaining xture.
CLEANING
Clean glass lens with nonabrasive glass cleaning solution.
CAUTION: Be sure xture temperature is cool enough to touch. Do not
clean or maintain while xture is energized.
GDSLIM62W IN 0713
INSTALLATION
Wire Guard mounts with (4) #8-32 x 1/2” stainless steel Screws to frame as
shown. Hardware is provided with guard. Guard and shield may be used
together.
1. Remove left and right Cover Plates and discard.
2. Line up guard with existing pre-drilled holes in frame as shown, tighten
screws.
Note: These instructions do not cover all details or variations in equipment nor do
they provide for every possible situation during installation, operation or maintenance.
Easy Installation & Product Help
Tech Help Line
Call our experts 888 RAB-1000
©2013 RAB LIGHTING Inc.
Northvale, New Jersey 07647 USA
rabweb.com
Visit our website for product info
email
Answered promptly sales@rabweb.com
Screws
Cover Plate
Screws (4)
Poly Shield
Housing
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

RAB Lighting GDWP2W Operating instructions

GDWP2W
RAB Lighting
Brand
RAB Lighting
Model
GDWP2W
Type
Operating instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers