GAI-Tronics 12562-109 Installation Kit

Brand
GAI-Tronics
Model
12562-109
Type
Installation Kit
Pub. 42003-236C
GAI-TRONICS 3030 KUTZTOWN RD. READING, PA 19605 USA
610-777-1374 800-492-1212 Fax: 610-796-5954
VISIT WWW.GAI-TRONICS.COM FOR PRODUCT LITERATURE AND MANUALS
GAI-TRONICS®
A
HUBBEL L COMPAN Y
Voice Annunciation PCBA Field
Installation Kit
MODEL 12562-109
Confidentiality Notice
This manual is provided solely as an operation, installation, and maintenance guide and contains sensitive
business and technical information that is confidential and proprietary to GAI-Tronics. GAI-Tronics
retains all intellectual property and other rights in or to the information contained herein, and such
information may only be used in connection with the operation of your GAI-Tronics product or system.
This manual may not be disclosed in any form, in whole or in part, directly or indirectly, to any third party.
General Information
The Model 12562-109 Voice Annunciation (VA) PCBA Field Installation Kit consists of a printed circuit
board assembly (PCBA), two lithium AA batteries, and three standoffs for mounting the VA PCBA to
the Main PCBA. The kit is designed to be used only in the following GAI-Tronics RED ALERT
®
Series
Emergency Telephones:
393-00x 393AL-00x 394AL-00x 396-00x
397-00
x 397-00xCB 397-00xRT 397-00xTP
398-00
x
398-00xCB 398-00xRT 398-00xTP
Electrostatic Discharge (ESD) Protection
Your telephone may have an earth ground terminal provision. If so, ensure that it is connected to ground
in accordance with all local safety regulations and the National Electrical Code (NEC). Grounding has to
be ensured for safe and stable communications. Do not use long and coiled ground wires. Trim ground
wires to the required length. Use a star configuration whenever possible.
Installation
Removing the Front Cover
Use the Model 233-001 Security
Screwdriver (Torx T-25 security tip) to remove the four (or six,
depending on the telephone model) front cover security screws, and remove the front cover after
disconnecting the telephone line.
Pub. 42003-236C
M
ODEL 12562-109 VOICE ANNUNCIATION PCBA FIELD INSTALLATION KIT Page 2 of 2
f:\standard ioms - current release\42003 kit manuals\42003-236c.doc
02/13
Installing the Voice Annunciation PCBA
1. Insert the three nylon standoffs on the existing Main PCBA in the locations shown in Figure 1.
2. Alig
n the plugs on the Voice Annunciation PCBA standoffs with the Main PCBA as shown in Figu
re
1 and snap in standoffs.
3. I
nstall the two AA lithium batteries in the correct +/−
orientation.
4. Reconnect the telephone line.
5. Refer to Pub. 42004-
438, RED ALERT
®
Installation Manual (“Voice Annunciation Option” section)
for set-
up and playback
instructions.
6. Use the Model 233-
001 Security Screwdriver (Torx T-25 security tip) to re-i
nstall the four (or six,
depending
on the telephone model) front cover security screws (10–12 in-l
bs. of torque
recom
me
nded).
Fig
ure 1. Installation of 12562-109 Voice Annunciation PCBA to Existing PBCA
  • Page 1 1
  • Page 2 2

GAI-Tronics 12562-109 Installation Kit

Brand
GAI-Tronics
Model
12562-109
Type
Installation Kit
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents