USER MANUAL
Dual Band Adjustable Repeater
PS800/700 System
User Manual of
Dual Band Adjustable Repeater RF37GS-PS7080
www.rftoo.com
QUICK START
Connection and Control Interface
Table 1. product description
Item Description
1 AC 110~240V; 50Hz power supply.
2 BS: Donor antenna port, uplink and downlink signals to base station.
3 MS: Service antenna port, uplink and downlink signals to mobiles.
*The picture is only for reference, please make the object as the standard.
1
2
3
User Manual of
Dual Band Adjustable Repeater RF37GS-PS7080
www.rftoo.com
Wall Mount Method
1. Use percussion drill to make four holes on the wall following the pattern in the
above diagram.
2. Push the WALLBOARD anchors to the holes. Drive two screws into the holes on
the top line. Do not fully tighten the screws.
3. Drive the other screws into the two holes on the bottom line. Do not fully tighten
the screws.
4. Check WALLBOARD alignment and tighten the 4 screws one by one.
5. Hold the REPEATER and push against the WALLBOARD. Align the top 4 holes
on the REPEATER with the WALLBOARD holes.
6. Drive four screws into the holes on the top line. Do not fully tighten the screws.
7. Drive the other screws into the two holes on the bottom line. Do not fully tighten
the screws.
8. Check REPEATER alignment and tighten the 8 screws one by one.
9. Ground the REPEATER properly to complete the installation.
Warning Message
Do NOT Turn ON the REPEATER until the BS and MS Ports are Connected
to Antenna or add load if no connected to Antenna.
Install the REPEATER Only in A Normal Indoor Environment.
The Dismantlement, Modification or Use of Any Object or Device to Alter or
Limit the Functionality, Permanently or Temporarily, of Any REPEATER
Structure Are Prohibited.
Place donna Antenna and service Antenna in reverse, and guarantee at least the horizontal
distance is 10 meters and vertical distance 3 meters.
User Manual of
Dual Band Adjustable Repeater RF37GS-PS7080
www.rftoo.com
User Manual
Section 1 Product Description and List of
Features
Dual band adjustable repeater allows small to medium size indoor areas have reliable
radio communications for first responders. Within the frequency range, 100KHz
adjustment step can be adjusted. Furthermore, customers can also change the
bandwidth between 0.1-18MHz (PS800) and 0.1-10MHz (PS700). Automatic gain control
allows stable output power even when the handheld is close to the repeater, which
protects the donor site from interruption. The unit is housed by a compact and light
alumina casting enclosure.
The built-in external LCD accessible from the bottom of the enclosure allow the uplink and
down link gains, Output Powers, Alarms and so on be configured and optimized easily on
site without additional tool. Signal strength indicator helps find donor signal source and set
up the system in the field without additional equipment.
Uplink/downlink frequency full range, or custom bands
Built-in Saw filter provides high out of band rejection
Built-in switches and signal strength indicator allow find donor signal source and
set up the system on site without additional equipment
External 100-240V AC universal power supply
Indoor wall mount
Heatsink convection cooling and low power consumption
Built-in ALC provides stable output power even when the handheld is close to the
repeater to minimize the interference to the donor site
User Manual of
Dual Band Adjustable Repeater RF37GS-PS7080
www.rftoo.com
Section 2 System Diagram
Fig.1 System Diagram
Section 3 Product Specifications
Table.2 Product Specifications
Items Uplink Downlink
Frequency Range
PS800 806~824MHz 851~869MHz
PS700 788~798MHz 758~768MHz
Center frequency adjustment step 100KHz 100KHz
Bandwidth
adjustable,
default=18Mz
PS800 0.1-18MHz 0.1-18MHz
Bandwidth
adjustable,
default=10Mz
PS700 0.1-10MHz 0.1-10MHz
Bandwidth adjustment step 100KHz 100KHz
Output Power
PS800 30±2dBm 37±2dBm
PS700 30±2dBm 37±2dBm
Max Gain 85±2dB 90±2dB
Gain Range 55~85dB 65~95dB
Ripple
PS800
≤6dB ≤6dB
PS700
≤4dB ≤4dB
Input VSWR
≤1.5 ≤1.5
Max. Input Power Without Over Drive -20dBm -20dBm
ATT step of 1 dB
(PS800)
1 ~ 10dB
∣△∣≤1dB ∣△∣≤1dB
10 ~ 20dB
∣△∣≤1dB ∣△∣≤1dB
20 ~ 30dB
∣△∣≤1.5dB ∣△∣≤1.5dB
User Manual of
Dual Band Adjustable Repeater RF37GS-PS7080
www.rftoo.com
Items Uplink Downlink
ATT step of 1 dB
(PS700)
1 ~ 10dB
∣△∣≤1dB ∣△∣≤1dB
10 ~ 20dB
∣△∣≤1dB ∣△∣≤1dB
20 ~ 30dB
∣△∣≤1.5dB ∣△∣≤1.5dB
AGC Active 30dB
∣△∣≤2dB ∣△∣≤2dB
Out of Band Gain
(PS800)
±600kHz ≤ 40dB ≤ 45dB
±1MHz ≤ 35dB ≤ 40dB
±5MHz ≤ 35dB ≤ 40dB
Out of Band Gain
(PS800)
±600kHz ≤ 40dB ≤ 45dB
±1MHz ≤ 35dB ≤ 40dB
±5MHz ≤ 35dB ≤ 40dB
EVM
≤ 12% ≤ 12%
PCDE
≤ -35dB ≤ -35dB
ACRR
5MHz
≤ -30dBc ≤ -30dBc
10MHz
≤ -30dBc ≤ -30dBc
Spurious
Emission
9KHz~1GHz
≤ -36dBm ≤ -36dBm
1GHz~12.75GHz
≤ -30dBm ≤ -30dBm
Noise Figure @ max. gain
≤ 6dB ≤ 6dB
Time Delay
≤ 8μs ≤ 8μs
Alarm
ALC not Active
—
Green
ALC Active 5-10dB
—
Orange
ALC Active 15-20dB
—
Red
broken No Light
self-excitation Red flashes
Low input signal green flashes
Power LED
Power ON Green
Power OFF No Light
AC Power 110~240VAC, 50Hz,
Display and Set LCD and Key
Display content
Frequency Range
DL Output Power
Gain
Alarm
Temperature
Power Consumption
≤220W
RF Connector N-Female
Environment Conditions IP65
Humidity < 90%
Operating Temperature
-30℃~+55℃
User Manual of
Dual Band Adjustable Repeater RF37GS-PS7080
www.rftoo.com
Section 4 Installation Instruction
4.1 Before Installation
Please verify the uplink and downlink frequencies labeled on the equipment, ensure they
match with your PO and your system requirements. Please contact your sales
representative if you find any discrepancy.
Install the equipment only in a normal indoor environment.
The built-in signal strength indicator supports quick deployment without additional tool and
equipment. However, we highly recommend that if possible, always use spectrum analyzer
and other equipment to assist the installation. Ideally, donor signal strength should have
been measured prior to the installation and the link budget and coverage have been
calculated by certified RF system design engineer. BOM, test plan and other documents
must be in place prior to the installation.
4.2 Check list
Please make sure the following items are included in the box delivered to you. If any item
is missing, contact your sales representative.
Table.3 check list
Item Quantity
The Repeater, 1
M10x60mm Screw with wallboard anchor 4
Customer Manual* 1
* Factory may choose to ship the product along with a hardcopy of this manual or make it
available electronically through website download or email.
User Manual of
Dual Band Adjustable Repeater RF37GS-PS7080
www.rftoo.com
4.3 Step by Step Installation Instruction
©
Fig.2 Installation Procedure
1. Find a proper indoor position where a good grounding path is available, usually
on a wall, and install the REPEATER following the steps given in the QUICK
START.
2. Follow the system design documents to locate the donor antenna ad service
antennas. The donor antenna and service antennas must have sufficient isolation,
and 90 dB minimum is recommended to ensure the device is working normally.
Donor antenna is typically installed on the rooftop or outside wall with high elevation,
avoiding any obstacle and in line of sight with the base station antenna. The
positions and number of service antennas must be designed properly by a qualified
Completion
Test for call qulitity
Adjust the direction of donor antenna
Connect power supply adapter
Measure receiving signal strength form base stantion
Install donor antenna and route feed lines
Install BDA on a wall
Indentify an installation location
Check contents of package
Inspection
User Manual of
Dual Band Adjustable Repeater RF37GS-PS7080
www.rftoo.com
system design engineer with proper RF planning tool.
3. Route the feed lines from the donor antenna to the REPEATER and service
antennas to the REPEATER following the system design documents. Connect
the feed line to donor antenna, and feed line to service antenna. Waterproof
the connections. Do not connect the feedlines to the REPEATER.
4. Verify isolation between donor antenna and service antennas. If a network analyzer
is available, it is recommended to verify the isolation between the donor antenna
and service antenna by bypassing the REPEATER and testing the transmission
between the port of the feedline to donor antenna and the port of the feedline to
service antenna. Minimum of 90dB is preferred. If the isolation is less than 85 dB,
report to your project manager and system design engineer. Relocate the donor
antenna, or service antenna might be necessary. If both options are not applicable,
then the REPEATER gain needs to be adjusted to avoid self-oscillation which
needs approval from the project manager and system design engineer, refer to
step 10
5. Adjust the donor antenna orientation.
5.1 If spectrum analyzer or other equivalent RF signal strength measurement
equipment is available (Highly recommended):
5.1.1 Set the spectrum analyzer's frequency range, bandwidth and other
parameters.
5.1.2 Connect donor antenna to the input port of spectrum analyzer.
5.1.3 Adjust donor antenna direction until -45dBm to -55dBm signal strength is
measured.
5.1.4 Connect the donor antenna port to the REPEATER ‘BS’ port.
5.2 Install the donor antenna without spectrum analyzer:
In case spectrum analyzer or other equivalent RF signal strength measurement
equipment is not available, the “Alarm” indicator on the front panel can be used to
adjust the donor antenna direction. When signal strength received from the donor
antenna is lower than -48dBm, the indicator is green; when the received signal
strength is higher than -35dBm, the indicator is red; when the received signal
strength is between -45dBm and -38dBm, the indicator is orange. It is suggested
to adjust the direction of the donor antenna to make the indicator just change
from green to orange which indicates the received signal strength is around
-48dBm.
5.2.1 Adjust the donor antenna direction until the “Alarm” indicator just change
from green to orange.
5.2.2 Connect the donor antenna port to the REPEATER “BS” port.
User Manual of
Dual Band Adjustable Repeater RF37GS-PS7080
www.rftoo.com
If the “Alarm” indicator stays green when you change the donor antenna direction,
this means the donor signal is too weak and you will get degraded coverage even
no coverage. Following are what you need to do
5.2.3 Immediately report to the project manager and system design engineer.
5.2.4 Recommend to confirm the signal strength using a spectrum analyzer if
possible.
5.2.5 Work with your project manager and system engineer, check if you can
replace the donor antenna by a higher gain antenna to get better signal.
5.2.6 Work with your project manager and system engineer, check if you can
relocate the donor antenna to get better signal.
6. Connect the service antenna to REPEATER’s “MS” port.
7. Set all attenuation switches on the ATT switch panel to off position, unless the
system design document requires to reduce the uplink and down gains from
factory default values.
8. Check and ensure “BS” and “MS” ports are connected to feedlines.
Connect the power adapter and plug in the power supply.
Follow the test plan, walk test the call quality in the service area.
9. When it is needed, service antennas may be relocated to satisfy coverage
requirement. You will need to get approval from your project manager and
system design engineer.
10. During the walk test, if self oscillation (Refer to Section 3) is observed, this means
either the donor signal is too strong or antenna isolation is insufficient. Report to
the project manager and system design engineer. Repeat Step 4, 5 and 8 if
possible.
11. The gain of uplink or the downlink, or both needs to be reduced. Use the
combination of switches 1-5 for uplink and 6-10 for downlink to reduce the uplink
and downlink gain respectively. Repeat the walk test until the coverage is
acceptable. Document and report to project manager and system design
engineer on the gain value settlement.
Document the installation and test reports, and submit to project manager for approval.
User Manual of
Dual Band Adjustable Repeater RF37GS-PS7080
www.rftoo.com
Section 5 Safety Information and Regulations
Do not dismantle the equipment.
Do not add extra pressure to REPEATER enclosure or attach anything to the
surface.
Use only the power adaptor supplied with the REPEATER, not any alternative.
The unit is for normal indoor environment application. Do not install the
REPEATER in a strong electric, high-intensity magnetic, corrosive, moist,
excessive temperature and other harsh environments.
Install the REPEATER in a place that is not accessible by kids and unauthorized
individuals.
Install and ground the unit following local inbuilding and communication site
construction codes.
It is your responsibility to ensure the use of REPEATER complies with FCC and
other regulations.
Do not power on the REPEATER before BS and MS ports are connected.
User Manual of
Dual Band Adjustable Repeater RF37GS-PS7080
www.rftoo.com
Section 6 Notices
1. Never Turn on the equipment until both “BS” and “MS” are connected to Antenna.
2. Always remove excessive feed lines from the equipment to donor antenna and
service antenna to minimize the cable loss.
3. Always install the donor antenna at the most available highest position and keep
distance from the service antenna to maximize the isolation between each other.
The vertical distance between donor and service antenna should be more than 3
meters.
4. Certain isolation between donor antenna and service antenna are required to avoid
self-oscillation. In case self-oscillation happens, reposition is required for the
antennas.
5. The donor antenna must be placed at least 2 meters away from other antennas on
the same site.
6. All feed line connections must be waterproofed.
Self-oscillation: During the walk test, if handheld indicates there is signal but no
communication, this often means self-oscillation occurs. Check the Alarm indicator, if it is
red, this means the donor signal is too strong or antenna isolation is insufficient. Adjust the
downlink attenuation, if the red indicator disappears, then this means the donor signal is
too strong. If the red indicator does not disappear, or the red indicator disappears only if
both uplink and downlink ATT switches are on, this indicates that there is no sufficient
isolation between the donor antenna and service antennas.
User Manual of
Dual Band Adjustable Repeater RF37GS-PS7080
www.rftoo.com
Section 7 Troubleshooting
Table 4. Troubleshooting
No Cause Alarm Run Action
1
Input signal level is
too low, receive
signal< -65dBm
Green
light blinks
Green
Adjust the place of donor antenna.
Then find stronger signal.
2
Signal is normal, the
receive signal
between -65dBm to
-45dBm
Green Green
-65dBm ≤X≤ -45dBm
This is the best working condition for the
repeater.
Do not need to take any action.
3 ALC work 5-10dB Orange Green Threshold :X≥ -42dBm
4 ALC work 15-20dB Red Green Threshold :X≥ -37dBm
5
ALC work>25dB,
self-excitation now
Red
light blinks
Red
light blinks
(1) Adjust the gain If the input signal
level is too high or the space of donor
antenna and service antenna is not
enough.
(2) If the red light still turning on that
means over accepting of donor antenna
or strong interference, then adjust the
place of donor antenna.
6 PLL unlocking No light Green
The equipment is broken,
Please contact supplier
7 temperature alarm
Red
light blinks
No light UL and PL power amplifier will turn off
8
Primary-slave
communication
exception
Green
Green
light blinks
User Manual of
Dual Band Adjustable Repeater RF37GS-PS7080
www.rftoo.com
Section 8 LED Display Panel of Operations Guide.
Display Details：
Working Frequency Range
Input & Output Power
Gain
Alarm items
1. Click “UL” or “DL”, click “OK”，Then you can see the frequency, click “OK” again,
click “+” or “-”
Setting the frequency range which you want and click “OK” finish.
Click “M” back to Main Menu.
User Manual of
Dual Band Adjustable Repeater RF37GS-PS7080
www.rftoo.com
2. Click “OUTPUT POWER”, click “OK”, real-time inquiry Uplink power and downlink
power, only for checking, NO setting. Click “M” back to Main Menu.
When the display power is below standard, Displayed as "---".
When the display power is above standard, displayed as “+++”.
3. Click “GAIN”, click “OK”, real-time inquiry Uplink gain and downlink gain, click “+” or
“-”，then setting gain which you want. click “OK” finish.
click “M” back to Main Menu.
User Manual of
Dual Band Adjustable Repeater RF37GS-PS7080
www.rftoo.com
4. Click “ALARM ITEMS”, click “OK”, real-time inquiry PLL, Downlink output power, AGC,
Temperature and RF switch.
Only for checking, NO setting. click “M” back to Main Menu.
（1）DL Output > 27dBm, OK change to Alarm;
（2）ALC work > 25dB, OK change to Alarm;
（3）The display shows the real-time temperature, if the temperature goes beyond the up
limit, displayed as “Alarm”.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
RFtoo RF37GS User manual
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Redutelco PORP23W User manual
-
DJ-Tech DIF-X User manual
-
G-Way Microwave / G-Wave Q8KBDALTEUC3390C User manual
-
-
Nikrans MA-600GDW User guide
-
Nikrans NS-450 User guide
-
Nikrans NS-1503G User guide
-
Nikrans NS-2500GD User guide
-
Nikrans NS-150GD User guide
-
Nikrans MA-300GDW User guide
