GS2002/GS2002V
GS2101/GS2101V
User Manual
WWW.GADSPOT.COM
CONTENTS
Chapter 1: DVR Features...................................................................................................................................................2
Chapter 2: Layout................................................................................................................................................................3
2.1 Front Panel ....................................................................................................................................................................3
2.1.1 4-Channel Front Panel .......................................................................................................................................3
2.1.2 8- Channel Front Panel ......................................................................................................................................3
2.2 Rear Panel......................................................................................................................................................................4
2.2.1 Channel Rear Panel............................................................................................................................................4
2.3 Remote Control ..............................................................................................................................................................5
Chapter 3: DVR Installation ..............................................................................................................................................6
3.1 Hard Drive Installation..................................................................................................................................................6
3.2 Camera and Monitor Connection...................................................................................................................................7
3.3 Power Supply connection...............................................................................................................................................7
Chapter 4: DVR Boot up ....................................................................................................................................................8
4.1 System Initialization.......................................................................................................................................................8
4.2 Main Interface................................................................................................................................................................8
Chapter 5: DVR Menu .........................................................................................................................................................8
5.1 Main Menu Preview .......................................................................................................................................................9
5.2 Main Menu.....................................................................................................................................................................9
5.2.1 Camera setup ....................................................................................................................................................10
5.2.2 Record setup......................................................................................................................................................10
5.2.3 Network Set........................................................................................................................................................11
5.2.4 Recording Search..............................................................................................................................................13
5.2.5 Multi player .........................................................................................................................................................14
5.2.6 Device Management.........................................................................................................................................16
5.2.6.1 HDD Management........................................................................................................................................16
5.2.6.2 Alarm Set .......................................................................................................................................................17
Email Alarm Notification...........................................................................................................................................17
5.2.6.3 PTZ Setup ......................................................................................................................................................18
5.2.6.4 Mobile............................................................................................................................................................19
Mobile Phone Access.................................................................................................................................................19
5.2.6.5 Motion Detect ................................................................................................................................................28
5.2.7 System Function................................................................................................................................................29
5.2.7.1 Time Set .........................................................................................................................................................29
5.2.7.2 Password ........................................................................................................................................................29
5.2.7.3 Video Setup....................................................................................................................................................30
5.2.7.4 Language........................................................................................................................................................30
5.2.7.5 Info.................................................................................................................................................................30
5.2.7.6 System Maintenance ......................................................................................................................................30
5.3 Menu Lock....................................................................................................................................................................31
5.4 Video Search.................................................................................................................................................................31
5.5 PTZ Control .................................................................................................................................................................31
5.6 Record ..........................................................................................................................................................................31
5.7 Stop recording..............................................................................................................................................................31
Chapter 6: Net-Viewer Program .....................................................................................................................................32
6.1 Plug-ins download and installation .............................................................................................................................32
6.2 Log-in to Net-Viewer....................................................................................................................................................32
6.3 Main Interface of Net-viewer .......................................................................................................................................33
6.3.1 Menu column......................................................................................................................................................33
6.3.1.1 Live................................................................................................................................................................33
6.3.1.2 Replay ............................................................................................................................................................33
6.3.1.3. Setup .............................................................................................................................................................34
① Record..................................................................................................................................................................34
② Alarm ...................................................................................................................................................................34
③ PTZ Control.........................................................................................................................................................35
④ Network ...............................................................................................................................................................35
⑤ Setting..................................................................................................................................................................35
⑥ Host Info ..............................................................................................................................................................36
6.3.2 PTZ Control(Numbers 2, 3, 4 on Picture 6-3) ...............................................................................................36
6.3.3 Live Play Control(Numbers 6 through 10 on Picture 6-3) ...........................................................................36
Chapter 7: Specification ......................................................................................................................................................37
Chapter 8: Windows Vista User..........................................................................................................................................37
Chapter 9: Appendix............................................................................................................................................................39
9.1 Operation Function Table............................................................................................................................................39
9.2 Recording Alarm setting...............................................................................................................................................40
9.3 Troubleshooting............................................................................................................................................................40
9.4 4 Channel System Connections....................................................................................................................................41
9.6 Accessory (Optional)....................................................................................................................................................42
User Manual
1
Safety Instruction
1. Use proper power source.
Do not use this product with a power source that applies more than specified voltage (100-240V AC).
2. Never insert anything metallic into the DVR case.
Putting something into the DVR case can be a source of dangerous electric shock.
3. Do not operate in wet & dusty area or use near water.
Avoid places like a damp basement or dusty hallway.
4. Do not expose this product to rain or use near water.
If this product accidentally gets wet, unplug it and contact an authorized dealer immediately.
5. Keep product surfaces clean and dry.
To clean the outside case of the DVR, use a cloth lightly dampened with water (no solvents).
6. Provide proper ventilation.
This DVR has a built in fan that properly ventilates the system.
7. Do not attempt to remove the top cover.
If there are any unusual sounds or smells coming from the DVR, unplug it immediately and contact an
authorized dealer or service center.
8. Do not attempt to remove the top cover.
Warning: You may be subjected to severe electrical shock if you remove the cover of the DVR.
9. Handle DVR box carefully.
If you accidentally drop your DVR on any hard surface, it may cause a malfunction. If the DVR doesn’t
work properly due to physical damage, contact an authorized dealer for repair or exchange.
10. Use standard lithium cell battery. (NOTE: Manufacturer has preinstalled battery.)
The standard lithium cell 3v battery located on the mother board should be replaced if the time clock
does not hold its time after the power is turned off. Warning: unplug the DVR before replacing battery or you
may be subjected to severe electrical shock. Properly dispose of old batteries.
11. Make sure there is good air circulation around the unit.
This DVR system uses a hard drive for video storage, which generates heat during operation. Do not
block air holes (bottom, upper, sides and back) of the DVR that cool down the system while running. Install
or place this product in an area where there is good air circulation.
.
User Manual
2
Chapter 1: DVR Features
Real time monitoring Supports real time surveillance via Monitor
Saves Recordings DVR saves real-time recording image to HDD
Backup Recordings Supports DVR backup via USB flash drive and hard drive.
Playback Recordings 4CH Supports DVR single CH and multiple CH playback of recorded files
8CH Supports DVR single CH playback of recorded files
Network operation Supports remote surveillance by multiple users simultaneously
Alarm Setting Supports HDD & video input alarm management
Mouse Operation Supports Mouse operation for faster menu navigation.
PTZ Control Supports PTZ camera operations through RS-485.
List 1-1
Other Features：
H. 264 video compression format： 4CH supports D1, HD1, and CIF resolution
8CH supports CIF resolution
ADPCM audio compression format
Windows Graphical interface
BNC and VGA video out ports
Supports remote live viewing via 3G mobile networks
Supports sending email alerts when motion is detected by system
Triplex (recording, playback and net transmitting at the same time)
Supports USB mouse, IR remote control operation
Rear USB2.0 ports for backup, upgrade and mouse operation.
Supports Double Encode bit network transmission
The video package time is adjustable
Multiple alarm record modes
Multiple languages OSD
Supports auto maintenance
User Manual
3
Chapter 2: Layout
2.1 Front Panel
2.1.1 4-Channel Front
Panel
1 :Rewind 10 Number 8 19 Number 5
2 :Pause 11 Number 9 20 Number 6
3 :Pla
y
12 0: Mute Audio 21 :U
p
Arrow
4 :Fast Forward 13 ALL :Dis
p
la
y
All Cameras 22 : Left Arrow
5 :Sto
p
14 Menu:Exit Menu 23 :Down Arrow
6 :Record 15 :CH1 24 :Ri
g
ht A
r
row
7 PWR: Power LED 16 :CH2 25 SEL: Select
8 HDD:HDD Lock 17 :CH3
9 Number 7 18 :CH4
List 2-1.1
2.1.2 8- Channel Front Panel
1 :Rewind 10 8 :CH8 19 5. : CH5
2 :Pause 11 Number 9 20 6. :CH6
3 :Pla
y
12 0 : Mute Audio 21 :U
p
Arrow
4 :Fast Forward 13 ALL :Dis
p
la
y
All Cameras 22 : Left Arrow
5 :Sto
p
14 Menu:Exit Menu 23 :Down Arrow
6 :Record 15 1. :CH1 24 :Ri
g
ht Arrow
7 PWR: Power LED 16 2. CH2 25 SEL: Selec
8 7 :CH7 17 4. :CH4
9 HDD:HDD Lock 18 3. :CH3 27
List 2-1.2
7 8 9 10 11 12 13 14
15 16 17 18 19 20 23
22 24
2
1 3 4 5 6 21 25
25
19
7 9 10 11 12 13 14 22 24
2
1 3 4 5 6 21
8
15 16 17 18 20
23
User Manual
4
2.2 Rear Panel
2.2.1 Channel Rear Panel
4CH
8CH
Item Physical port Connection method
1 Video input Connect CH1-4 ( BNC interface)
2 Video output Connect monitor output ( BNC interface)
3 Audio input Connect signal input (RCA interface)
4 Audio output Connect signal output (RCA interface)
5 Ethernet Port Connect intranet, internet (RJ45 interface)
6 VGA Port(Optional) Connect to VGA monitor
7 USB Port Connect USB mouse
8 RS-485 RS485
9 Power Port Connect power supply - DC12V 3A
7
6
4
32 1
5 8 9
7
6
4
32 1
5 8 9
User Manual
5
2.3 Remote Control
Mouse Operation
You can use a mouse instead of front panel buttons or remote control.
In menu lock mode, Enter into pop-up menu and clicking any sub menu to pop up Log-in
window; on menu unlock mode, enter into pop-up menu, and then clicking left key to enter
into any sub menu directly.
After entering main menu, clicking left key could enter into any sub menu; On[Detailed
file] menu mode, clicking left key could playback one recording file.
Change the status of check box and motion detection area.
Clicking combo box to access pull-down menu
By clicking left key you can adjust Color control bar and volume control bar.
By clicking left key you can select values in edit boxes or pull-down menu and supports
Chinese word input, special symbol, numeric and character input, use instead of
[Enter- ] or [Backspace ]
Click left key of
Mouse
In the [Detailed file] menu mode, clicking left key will playback one recording file.
In live display mode, clicking right key will display pop-up menu (shown as Picture 5-1).
Click right key of
Mouse In Main menu or sub menu mode, clicking right key will exit current menu.
Double-click Left
key of Mouse In live display or playback mode, double-clicking left key will maximize the screen.
Moving Mouse Select menu item
Sliding Mouse On motion mode, sliding mouse will select motion area; On [Color set] menu mode,
sliding mouse will adjust color control bar and volume control bar.
List 2-3
1 1-8 Channel Select 1-8 ; Numeric key
2 9、0 Numeric Key
3 ALL Preview all Channel
4 Menu Enter/Exit Main Menu
5 ▲ Up Key
6 ▼ Down Key
7 ◄ / Left / Right Key
8 SEL Select Key/ Edit Key
9 Rewind key
10 Play Key, Enter to recording search menu
11 Forward Key
12 ● Manual Recording
13 Pause / Frame Play
14 ■ Stop manual recording; Stop Playback
15 Audio Undefined
16 Mute Undefined
User Manual
6
Chapter 3: DVR Installation
3.1 Hard Drive Installation
Caution： Please do not Install or take out hard drive when DVR is running!
First, loosen the screws in the left and right sides.
Secondly remove the cover
Third, connect data cord and power cable of main board to the according ports of DVR.
User Manual
7
Next, Install HDD on the bracket fix then with screw, firmly secure the screw so that it can not get loose from such as
vibration.
Next, check if the connectors are properly connected and there is no problem with wiring and close up cover and fix it
with screws.
3.2 Camera and Monitor Connection
Connect camera cable to video input of DVR, and from video output of DVR to Monitor via BNC
connector (Refer to section2.2-Rear Panel); or
If the camera is a PTZ speed dome, you could connect RS485 A & B to the according port of DVR
respectively (refer to system figuration on Chapter 8).
3.3 Power Supply connection
Please only use the power adapter supplied with the DVR.
User Manual
8
Chapter 4: DVR Boot up
4.1 System Initialization
4.2 Main Interface
z
Chapter 5: DVR Menu
Pop-up Menu
After finishing system initialization, click right key of mouse on main
interface mode to enter into Pop-up Menu. Now you could carry out parameter
setting and operate for Main Menu, Menu Lock, Video Search, PTZ, Start
record, Stop Record and also operate for Start Cruise after successful PTZ
parameter setting etc.
After connecting the power adapter，the system will boot-up
and start initializing.
After finishing system initialization, the system will enter into main
interface. Picture 4-2 is the main interface displayed by system, which is
showing no video input status. Once there are video inputs, the interface
will display live images from the cameras. In main interface mode, if you
use the mouse to double-click the live image of any channel, the image will
be maximized to full screen, by double-clicking again, the display will be
come back to display all cameras; clicking the right button of the mouse,
will enter into Pop-up Menu; by clicking the left button of the mouse, you
select menu items; when clicking any area outside the menu, you will exit
the Pop-up menu.
Picture 4-1
Picture 4-2
Picture 5-1
User Manual
9
5.1 Main Menu Preview
5.2 Main Menu
setting, User password, Audio/Video setting, Language select, and access system information, system
maintenance etc.
After clicking right button of mouse, pop-up menu will be displayed on
the screen. You can click [main menu] button on pop-up menu to enter
into Main menu interface (Shown as Picture 5-2). You can also use the
Menu button on the front panel to bring up the window, when using the
front panel buttons use the FWD and REW button to move in the
menu, and the SEL button to select the icon. You use the ESC button
to return to previous window. In Main Menu mode, you can control
device management settings, such as Camera, Recording, Network,
Recording search, HDD, Alarm, PTZ Control, Mobile Phone & motion
detection etc
,
y
ou can also set s
y
stem function settin
g
s
,
such as Time
Picture 5-2
Main Menu
Rec. Search
Search
Playback
File List
Camera
Recording
HDD Management
Alarm Setting
PTZ Setting
Mobile
Motion
Color set
System
User password
System Information
Language Select
System Maintenance
Video Setting
Time Setting
Device
Management
Network Setup
Area setting
E-mail setting
Dwell time display
Detail File File backup
User Manual
10
5.2.1 Camera setup
Explanation：
1、The modifications will be available after clicking [APPLY] button on the bottom of the sub-menu windows
and being prompted to save and then clicking [ok] button.
2、If you want to cancel the modification, click [Exit] button to exit the menu.
3、When clicking [DEFAULT] button, all system default values will be reset to default value.
4、System default value indicates the value pre-set at the factory.
5.2.2 Record setup
Go to [Main Menu Camera] to set up the name display
and position display of each channel (Shown as Picture 5-3), You
can also adjust image brightness, saturation, contrast and hue
settings of each channel after entering into [Color] Menu and set
up whether each channel can be previewed or not under Live
display and/or Recording mode.
Please note that the name of each channel supports up to
eight characters.
Click [Main Menu] [Record] to enter into [Record Setup]
menu (Shown as Picture 5-5)
Functions：
1、The [ Rec. Mode] button allows you to setup recording 24
hours, on motion, or on a set schedule.
2、[PACK time] indicates maximum continuous time length of
recorded files (15, 30, 45, 60 min).
Below is the Color Menu where you can adjust image
brightness, saturation, contrast and hue parameters of each
channel.(shown as picture 5-4)
Click [AUTOSEQ] button to start auto rotation function.
(setting sub menu shown as Picture 5-4A. After starting auto
rotation function, system will auto rotate the video images among
CH1, CH2, CH3, CH4 and Quad (4CH) or CH1、CH2……CH8
and all CHS(8CH) in turn.
Default rotation time: 5 second
Settable time range: 0~10 second
Note: After apply “AUTOSEQ”, you can exit the menu and
click “▌▌ Pause” on front panel or remote control let it this
function realize.
Picture 5-4A
Picture 5-3
Picture 5-4
Picture 5-5
User Manual
11
The [Record Setup] menu allows you set up recording status (on/off) of each channel, it also allows you
setup recording image resolution and quality, and turn audio on/off. This menu also allows you select
recording mode (recording after power on and scheduled recording) and recording file length.
Once a channel is set to “on”, the channel can record, if it is set to “off”, the video from the channel will
not be recorded. Resolution options are D1, HD1 and CIF(4CH only); and Quality options are Best, Good
and Normal.
When Audio is set to “On”, system will also record audio from the channels and will have audio output on
playback mode; if it is set to “off”, you can not record audio and will have no audio output available on
playback mode.
To record 24 hours a day, set the Rec Mode to Always. To record on motion or a set schedule, select
Time Schedule Record and click the “Schedule” option, the Schedule interface will open as shown in (picture
5-6):
complete the schedule you activate it by clicking the [Apply] button.
You can also click on the Default button to use the system defaults. The system default settings are:
Hr01:00 am-07:59 am : No recording
Hr08:00 am-18:59 pm : Normal recording
Hr19:00 pm- 00:59 pm : Alarm recording
Explanation: Under the recording Set menu and recording search menu, original color stands for no
recording, “Red” stands for alarm recording, “Green” stands for normal recording and “Blue” stands for the
channel and date you have selected.
5.2.3 Network Set
Enter into [Main MenuNetwork Set] to proceed network set (Shown as picture 5-7):
After selecting network mode - such as DHCP、PPPOE and
static allocation and setup web port, you could visit DVR remotely
via network.
Picture 5-7
Recording options include All, CH-1, CH-2, CH-3, CH-4 or CH1 to
CH8 respectively. Please click the channel you need, the channel you
select will be highlighted in “Blue” unselected channels will be “Grey”.
To setup weekly schedules, click on the box of the recording
status you want (Alarm, General, or No Record) and then click on
each box in the schedule time line that you want this method to apply
to. You can use the [From – To] pull-down menus and Copy button to
copy settings from one day to another day or all days. After you
Picture 5-6
User Manual
12
When selecting DHCP, DHCP server will allocate DVR IP address automatically.
Picture 5-9
Picture 5-8
When selecting PPPoE, you need to input user and password
provided by ISP supplier and set up web port (details please refer
to the below picture 5-8).
Picture 5-9
When selecting static allocation, you need to setup IP address,
net-mask, gateway and web port (shown as picture 5-9).
Picture 5-11
If you need to visit DVR via Internet, you should setup the
inflection of video port at the public Router located in the DVR
(shown as Picture 5-11).
Host Port: 9000
Web Port: 8080
LAN IP address of DVR: 192.168.1.101
Input http:// router IP:8080 (192.168.1.101:8080) to you
computer IE browser,then you will visit your DVR freely.
Picture 5-10
If you apply for DDNS service and set up net parameter of
DVR accordingly, you could visit DVR remotely via IE browser.
(shown as picture 5-10)
User Manual
13
5.2.4 Recording Search
Click [Main menu search] to enter into [Video Search] menu (shown as the below picture 5-12).
You can play video Forward at 2x, 4x, and 8x speeds, Slow play at 1/2x, 1/4x, and 1/8x, normal play,
pause and play frame by frame using the playback control bar, and adjust volume by clicking or sliding tune
control bar. When playback has finished, system will return to previous menu.
File list
On the [Video search] menu mode, click [File list] menu to pop up the sub-menu shown below as Picture
5-21.This option will allow you to view all of the available files by channel and type (all, normal, or alarm).
You can select a file and push the SEL button to playback the file, or use the FWD button and down button to
select the option and backup the recording file you selected. You can also put a checkmark in the box at the
end of multiple files if you want to backup more then one file.
LAST (Last page): Indicates the last page of recording history you have searched. When you view other
pages, clicking [Last page] button will take you to the Last page.
ALL (Select All): Allows you to select all the events on the current page.
INVERSE (Select Invert): Allows you to select other events on the current page except those you have
currently selected.
Recording File Backup
If you want to backup one recording from the file list, you just select the recording and click [Backup]
button. When the backup is completed you will be notified. Please click [OK] button to save your backup
(shown as Picture 5-14).
Searched playback:
If you input specific date and click [Search], you will find all the
recordings for that day. When you select [Date] item, you will
playback the recordings in 4 channel mode (4 CH only); or, click [File
list] button to display File list interface, where you can playback or
backup the file you selected. See File List heading below.
Picture 5-12
Picture 5-13
First：Indicates the first page of recording history you have
searched. When you view other pages, clicking [First] button brings
you back to Page one.
PRE (Previous page): When viewing event list, clicking [Previous
page] button will take you back to page before the one you are
currently viewing (except the first page).
NEXT (Next page): When viewing event list, clicking [Next page]
button will take you to the page after the one you are currently viewing
(except the last page).
User Manual
14
Explanation: Backup file will be in H264 format, you can convert it to AVI format using the Multimedia
Player program that comes with the DVR or through the net-viewer program, so you can use any player
which supports AVI format.
5.2.5 Multi player
1、Copy backup file to your PC.
2、Open multimedia player and click [File Local (F)] to find/select the backup file, and then click [open]
button
Note: the file type you have selected should be *.264 format.
3、Open backup file:
（2）、Click pop-up menu button on the bottom of multimedia player and [Play- ] button, then
the backup file will be played on the according channel.
（3）、The Menu brief on the bottom of multimedia player:
Picture 5-14 Picture 5-15
Picture 5-16 Picture 5-17
（1）、Click [Play] menu (P) on the top of multimedia player
interface to select playing the backup file;
Picture 5-18
User Manual
15
Date: recording date for the current backup file shown as right corner;
24H recording time: lie under [Date] menu. Black number button stands for current recording
playback is normal recording for the time line.
0~60 Minute recording time quantum: Green part on play processing bar stand for recording length
for one hour recording.
Recording date and time processing for the current recording file
1 Pla
y
10 All the windows
2 Previous recordin
g
file 11 Add window
3 Pause 12 Start
4 Stop 13 Cut
5 Previous frame / Next frame 14 Delete
6 Slow pla
y
, Normal pla
y
, Fast Pla
y
15 Convert AVI
7 Next Hou
r
16 OSD
8 Capture picture 17 Mute switch
9 Reduce window 18 Volume ad
j
ust
4、Please refer to the below [Video on] setting procedure (System default - video for every channel is on)
5、Refer to the below for [Audio on] setting procedure. (Setting parameter will be available after re-starting
multimedia player after [Audio on] set up.)
SettingAudio channel setting Normal video BarSelect the channel you want to playback the
SettingVideo play setting Normal video
BarSelect the channel you want to display Select
to play the videoApplyOK
Picture 5-19
Picture 5-20
User Manual
16
audioSelect the channel has audio filesApplyOK.
After successfully setting the above, when you playback the current channel, you can open the channel’s
audio function at the same time as the video
5.2.6 Device Management
5.2.6.1 HDD Management
OVERWRITE: If you select “on” the system will automatically overwrite the oldest recordings once the
hard drive is full; if you select “off”, recording will stop once the hard drive is full.
HDD FORMAT: You use this option to format the hard drive, you can not record files to the hard drive
until it has been formatted. Click [Format HDD] button to start formatting. When selecting [Format HDD]
option the system will prompt you – “Format HDD will loss all the data, do you confirm?” ; click “OK”, system
will prompt you – “Is formatting…” and “successful format”; and then system will restart automatically.
USB FORMAT: Use this option to format USB devices.
Options in device management include hard drive,
Alarm, PTZ control, Mobile Phone Monitoring, and Motion
Detection.
Click [Main MenuDevice HDD] to enter [HDD
Management] menu (shown as Picture 5-24)
When you install a HDD, the system will automatically detect
if HDD is formatted or not; If HDD needs to be formatted, HDD
status will be shown as “Not format”, otherwise, the HDD status
will be shown as “Normal” (refer to Picture 5-25)
TOTAL SPACE: Indicates total space available on Hard
Drive.
FREE SPACE: Indicates unused space available on the
Hard Drive.
USEABLE REC TIME: Based on current image
detail/quality and frame rate, system will show you how
Recording time you have left on the Hard Drive.
Picture 5-21 Picture 5-22
Picture 5-23
Picture 5-24
Picture 5-25
User Manual
17
5.2.6.2 Alarm Set
HDD SPACE: Options are “On” and “Off”. When the alarm function is on, there are alarm sounds when
the HDD is running out of space; when the function is off, there are no alarm sounds.
VIDEO LOSS: Options are “On” and “Off”. When the function is on, system will issue alarm sound and
display video loss on the preview interface; when the function is off, system will have no alarm sound, but the
preview interface will display video loss.
Alarm Type Function
Video Loss Sends alarm when DVR can’t receive video signal (such as camera damage, cable broken or damaged
or power supply malfunction).
Motion Detection When an object moves into motion detection area, alarm will be triggered. You can adjust
sensitivity level to suit the needs of your actual application environment.
HDD loss When Hard Drive is not detected (HDD damage, power supply malfunction), or HDD auto-overwrite
is off, and free space is not enough, an alarm will be triggered.
List 5-1
Email Alarm Notification
(to send notice to email account when motion alarm is triggered)
Please set SSL to “On” via Gmail.com server, and set to “Off” via other mail server.
Click the [Email setup] menu to enter into its sub menu
(shown as Picture 5-27).
Pi
ctu
r
e
5
-27
On the [Email setup] mode, refer to its parameter setup
shown as picture 5-28 when setting email alarm to “on”.
SSL: is a security link transport protocol. You can encrypt your
communication info (including your email) using SSL to prevent hackers from
monitoring your email or communication info and even your password.
Pi
ctu
r
e
5
-2
8
Click [Main MenuDevice Alarm] to enter into [Alarm setup]
menu to setup Alarm warnings (shown as Picture 5-32).
HDD LOSS: Options are “On” and “Off”. If you select On there
will be a buzzer sound and “H” sign on screen when HDD is not
detected or not formatted; on the contrary, if you close the function,
there is only “H” sign to indicate HDD not found, but no alarm sound
when HDD not found or not formatted.
Picture 5-32
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
Gadspot GS2101 User manual
- Category
- Digital Video Recorders (DVR)
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
