Imtra Sardinia Operating instructions

Brand: Imtra

Model: Sardinia

Category: Motorcycle Accessories

Type: Operating instructions

This manual is also suitable for

Cyprus

Imtra Sardinia is an energy-saving LED spot light fixture that can directly replace halogen spotlights commonly found on vessels and megayachts. It features built-in current-regulated drive electronics and accepts 120VAC line-voltage, simplifying electrical hook-up and eliminating the need for external drivers or transformers. The fixture has a 3.76" (96mm) trim ring diameter and a 2.89" (73mm) recess cutout diameter. It provides 10.

OVERVIEW

The Sardinia and Cyprus are energy saving flush-mount spots

that directly replace power-hungry 120V-35W halogen spots

commonly found on large vessels and megayachts. Both feature

integrated current-regulated drive electronics that accept

120VAC line-voltage; greatly simplifying electrical hook-up and

eliminating the need for external drivers, LED converters, or step-

down transformers required by mainstream LED and halogen

products.

The fixed direction models may be either screw mounted

or secured with the springs provided. The Cyprus Eyeball

model mounts with springs only. An 18” long triplex cable is

provided for connection to a junction box or use the optional

bracket with Molex™ connector (included with each unit). The

Sardinia and Cyprus’ thermal management system includes

efficient heat sink design and thermal compensator that powers

down the unit in the event of high ambient heat conditions or

overheating. Emitting no radiated heat, these fixtures will keep

cabin temperatures comfortable and eliminate risk of burning or

scorching, long associated with hot halogen bulbs. Finally, our

use of high quality LEDs and custom-built solid state electronics

contributes to long fixture life, eliminating the cost associated

with changing delicate bulbs.

- 1 -

SPECIFICATIONS

Sardinia Cyprus

Cyprus

Eyeball

Trim Ring Diameter 3.76” (96mm) 3.76” (96mm) 3.79” (96mm)

Trim Ring Height 0.27” (7mm) 0.27” (7mm) 0.25” (6.25mm)

Recess Cutout Diameter 2.89” (73mm) 2.89” (73mm) 3.38” (85.7mm)

Recess Depth 2.81” (71mm) 2.81” (71mm) 2.86” (72.7mm)

Input Voltage Range 90-135 VAC

Power Consumption 10.5 Watts

IP Rating IP65* IP40**

* IP65: “Protected from the ingress of dust and low pressure jets of water from all directions”

This rating does not apply to the rear of the fixtures.

**IP40: “Protected against solid objects down to 1mm. No protection against direct sprays of

water.”

- 2 - - 3 -

PowerLED Downlight

Installation and Operation Manual

Sardinia Cyprus

Cyprus

Eyeball

PHYSICAL INSTALLATION

It is imperative that the lights are mounted in such a location that

the fixtures are protected from the rear against water exposure.

Also, it is important that the lights are mounted with airspace

around the heat sink housing to allow for convective cooling

of the lights. We recommend a distance of ½” (13mm) of free

space above the housing.





- 4 -





½” (13mm)

Resonance suppression

band (do not remove)



Spring Mount Installation Instructions

1. A. For Sardinia/Cyprus fixed

direction models: Cut a 2 7/8”

(73mm) diameter circle in the

mounting surface.

B. For Cyprus Eyeball: Cut

a 3 3/8” (85mm) circle in the

mounting surface, Note: the hole

must not be any larger than this.

2. Connect the light to an AC power

source following the Wiring

Instructions in the next section of

this guide.

3. Once all electrical connections are

made and secure, gently bend

back the mounting springs of your

PowerLED and insert the spring

tips into the cutout circle in the

mounting surface (see Figure 1).

- 5 -

Figure 1

Screw Mount Installation Instructions

1. For Sardinia/Cyprus fixed direction

fixtures: Cut a 2 7/8” (73mm) diameter

circle in the mounting surface.

2. Connect the light to an AC power

source following the Wiring

Instructions in the next section of this

guide.

3. Once all electrical connections

are made and secure, insert your

PowerLED into the cutout circle and

fasten with #4 flat head screws (see

Figure 2).

4. Place the trim ring over the light

making sure the tabs of the housing

engage the openings of the trim ring.

Twist the trim ring on to secure it.

Figure 2

Use #4 at head

screws only

- 6 - - 7 -

WIRING INSTRUCTIONS

1. Wiring connections shall be made within

the necessary enclosures (junction boxes) as

required by any applicable standards, codes

or laws. The available bracket and Molex

connector may be used where appropriate.

Otherwise, 18” of triplex cable is provided to

allow proper wire routing to a suitable location.

2. Connect the light to an AC power source by connecting the

white wire to neutral, the black wire to live and the green/

yellow wire to ground.

3. If a dimmer is used, the black wire should be connected to the

terminal or wire labeled “LOAD” on the dimmer.

4. Please refer to wiring diagrams and dimmer compatibility

chart on pages 8-11.

Wire Function

Black Live

White Neutral

Green/Yellow Ground

IP40 & IP65 models

IP65 models only

DIMMER COMPATIBILITY CHART

The Sardinia and Cyprus light fixtures are designed to operate with

most Electronic Low Voltage, Phase Control dimmers. Below is a list of

dimmers that have been tested and approved by Imtra.

Brand Model

Lutron® Skylark® SELV-300P

Lutron® Nova® NELV 450

Lutron® Maestro® MAELV-600-IV

Lutron® Nova T® NTELV-600

Lutron® Grafik Eye® w/Diva® Control PHPM-WBX w/DVF-103P

Lutron® Panel Module HW/LP-RPM-4A-120

Lutron® RadioRA RRD-6NA

Crestron® DIN-1DIMU4

Crestron® CLX-1DELV4

Crestron® CLS-EXP-DIMU

- 11 -

Wiring Diagram - One Way Switching

No Dimming•

Single Switch Location•

- 8 -

Live

Neutral

Ground

1-Way Switch

1P/1T - On/Off

Sardinia or

Cyprus

Sardinia or

Cyprus

90-135VAC





Wiring Diagram - Three Way Switching

No Dimming•

Multiple Switch Location•

- 9 -

3-Way Switch

1P/1T - On/On

3-Way Switch

1P/1T - On/On

Live

Neutral

Ground

Sardinia or

Cyprus

Sardinia or

Cyprus

90-135VAC





Wiring Diagram - Dimming

With Dimming•

- 10 -

Live

Neutral

Ground

Sardinia or

Cyprus

Sardinia or

Cyprus

90-135VAC





LIMITED WARRANTY

Imtra warrants the light-emitting LSA (LED spotlight assembly)

component of our IML PowerLED spot lights & fixtures for 5 years

from the date of purchase. If the LSA should cease to function within

5 years, return the complete spot light assembly to Imtra for repair or

replacement.

This warranty does not apply to damage resulting from actions of the

user such as misuse, improper wiring/installation, operation outside of

specification, improper maintenance or repair, unauthorized modification,

lightning strike or damage from a power surge.

The trim ring (bezel) of the IML Power LED spot lights are warranted for

either two years (stainless steel or powder coated) or one year (gold or

satin-nickel) depending on the finish of the fixture.

Imtra specifically disclaims any implied warranties, merchantability or

fitness for a specific purpose and will not be liable for any direct, indirect,

incidental or consequential damages. Imtra’s total liability is limited to

repair or replacement of the product.

The warranty set forth above is inclusive and no other warranty, whether

written or oral, is expressed or implied.

If it should become necessary to return a fixture for service during or

beyond the warranty period, please refer to Imtra’s standard Return Policy

as detailed on Imtra’s website (www.imtra.com) or call Imtra customer

service at (508) 995-7000.

No returns are accepted without a Return Authorization (RA) number.

- 12 -

30 Samuel Barnet Boulevard, New Bedford, MA 02745

(508)995-7000•www.imtra.com

Imtra Sardinia Operating instructions

Brand: Imtra

Model: Sardinia

Category: Motorcycle Accessories

Type: Operating instructions

This manual is also suitable for

Cyprus

Download PDF

report

Imtra Sardinia Operating instructions

This manual is also suitable for

Imtra Sardinia Operating instructions

Other documents