Ryobi CHI1802M User manual

Page is loading ...

Attention !

Il est indispensable que vous lisiez les instructions contenues dans ce manuel avant

le montage et la mise en service de l’appareil.

Important!

It is essential that you read the instructions in this manual before mounting and operating

this machine.

Achtung!

Bitte lesen Sie unbedingt vor Montage und Inbetriebnahme die Hinweise dieser Bedienungsanleitung.

¡Atención!

Es imprescindible que lea las instrucciones de este manual antes del montaje y de la

puesta en servicio.

Attenzione!

Prima di procedere al montaggio e alla messa in funzione, è indispensabile leggere

attentamente le istruzioni del presente manuale.

Atenção!

É indispensável ler as instruções deste manual antes de montar e pôr em serviço.

Let op !

Het is absoluut noodzakelijk vóór montage en inbedrijfstelling de aanwijzingen in deze

handleiding te lezen.

Observera!

Det är nödvändigt att läsa instruktionerna i denna bruksanvisning före montering och

driftsättning.

OBS!

Denne brugsanvisning skal læses igennem inden montering og ibrugtagning.

Advarsel!

Vennligst les instruksjonene i denne bruksanvisningen før du monterer og tar i bruk

maskinen.

Huomio!

On ehdottoman välttämätöntä lukea tässä käyttöohjeessa annetut ohjeet ennen

asennusta ja käyttöönottoa.

Προσοχή!

Είναι απαραίτητο να διαβάσετε τις συστάσεις των οδηγιών αυτών πριν τη

συναρμολόγηση και τη θέση σε λειτουργία.

Figyelem! Feltétlenül fontos, hogy a jelen használati útmutatóban foglalt előírásokat az

összeszerelés és az üzembe helyezés ellőt elolvassa!

Důležité upozornění! Před montáží nářadí a uvedením do provozu je nutné si přečíst následující pokyny.

ÇÌËÏ‡ÌËe! èee‰ Ò·ÓÍÓÈ Ë Á‡ÔÛÒÍÓÏ ËÌÒÚÛÏeÌÚ‡ ÌeÓ·ıÓ‰ËÏÓ ÔÓ˜eÒÚ¸ ËÌÒÚÛÍˆËË ËÁ Ì‡ÒÚÓﬂ˘e„Ó

ÛÍÓ‚Ó‰ÒÚ‚‡.

Atenţie! Este indispensabil sã citiţi instrucţiunile conţinute în acest mod de utilizare înainte de montaj

şi de punerea în funcţiune.

Uwaga! Przed montowaniem i uruchomieniem, koniecznie musicie się Państwo zapoznać

z zaleceniami zawartymi w niniejszym sposobie użycia.

Pomembno! Zelo pomembno je, da pred namestitvijo in prvo uporabo te naprave preberete

navodila v tem priročniku.

Upozorenje!

Vaæno je da upute u ovom KorisniËkom priruËniku proËitate prije postavljanja i uporabe ovog alata.

Dikkat! Montajdan ve aletin kullanımına başlamadan bu kılavuzda bulunan talimatları

okumanız gerekmektedir.

Sous réserve de modifications techniques / Subject to technical modifications / Technische Änderungen vorbehalten /

Bajo reserva de modificaciones técnicas / Con riserva di eventuali modifiche tecniche / Com reserva de modificações técnicas /

Technische wijzigingen voorbehouden / Med förbehåll för tekniska ändringar / Med forbehold for tekniske ændringer /

Med forbehold om tekniske endringer / Tekniset muutokset varataan / Υπό την επιφύλαξη τεχνικών τροποποιήσεων /

A műszaki módosítás jogát fenntartjuk / Změny technických údajů vyhrazeny /

åÓ„ÛÚ ·˚Ú¸ ‚ÌeÒeÌ˚ ÚeıÌË˜eÒÍËe ËÁÏeÌeÌËﬂ /

Sub rezerva modificaţiilor tehnice / Z zastrzeżeniem modyfikacji technicznych / Tehnične spremembe dopuščene

Podloæno tehniËkim promjenama / Teknik düzeltmeler hakkı saklıdır

960931224-01B.indd A4960931224-01B.indd A4 7/20/07 11:16:35 AM7/20/07 11:16:35 AM

Page is loading ...

GENERAL SAFETY RULES

WARNING

Read all instructions. Failure to follow all

instructions listed below may result in electric

shock, fire and/or serious injury. The term "power

tool'' in all of the warnings listed below refers

to your mains operated( corded) power tool or

battery operated( cordless) power tool.

SAVE THESE INSTRUCTIONS.

WORK AREA

■ Keep work area clean and well lit. Cluttered and

dark areas invite accidents.

■ Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases, or dust. Power tools

create sparks which may ignite the dust or fumes.

■ Keep children and bystanders away while

operating a power tool. Distractions can cause you

to lose control.

ELECTRICAL SAFETY

■ Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed(grounded) power

tools. Unmodified plugs and matching outlets will

reduce risk of electric shock.

■ Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

■ Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

■ Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords increase

the risk of electric shock.

■ When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electric shock.

PERSONAL SAFETY

■ Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under

the influence of drugs, alcohol or medication. A

moment of inattention while operating power tools

may result in serious personal injury.

■ Use safety equipment. Always wear eye

protection. Safety equipment such as dust mask,

non-skid safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce personal

injuries.

■ Avoid accidental starting. Ensure the switch is in

the off position before plugging in. Carrying power

tools with your finger on the switch or plugging in

power tools that have the switch on invites accidents.

■ Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may

result in personal injury.

■ Do not overreach. Keep proper footing and

balance at all times. This enables better control of

the power tool in unexpected situations.

■ Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewellery or

long hair can be caught in moving parts.

■ If devices are provided for the connection of dust

extraction and collection facilities, ensure these

are connected and properly used. Use of these

devices can reduce dust related hazards.

POWER TOOL USE AND CARE

■ Do not force the power tool. Use the correct

power tool for your application. The correct power

tool will do the job better and safer at the rate for

which it was designed.

■ Do not use the power tool if the switch does not turn

it on and off. Any power tool that can not be controlled

with the switch is dangerous and must be repaired.

■ Disconnect the plug from the power source before

making any adjustments, changing accessories,

or storing power tools. Such preventive safety

measures reduce the risk of starting the power tool

accidentally.

■ Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the

power tool or these instructions to operate the

power tool. Power tools are dangerous in the hands

of untrained users.

■ Maintain power tools. Check for misalignment or

bindling of moving parts, breakage of parts and

any other condition that may affect the power

tools operation. If damaged, have the power tool

repaired before use. Many accidents are caused by

poorly maintained power tools.

8

GB

English

F

D

E I

P NL

S DK N FIN GR

H CZ RUS PL

RO

SLO TR

HR

960931224-01B.indd 8960931224-01B.indd 8 7/20/07 11:16:38 AM7/20/07 11:16:38 AM

GENERAL SAFETY RULES

■ Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

■ Use the power tool, accessories and tool bits etc.,

in accordance with these instructions and in the

manner intended for the particular type of power

tool, taking into account the working conditions

and the work to be performed. Use of the power

tool for operations different from intended could result

in a hazardous situation.

BATTERY TOOL USE AND CARE

■ Ensure the switch is in the off position before

inserting battery pack. Inserting the battery pack

into power tools that have the switch on invites

accidents.

■ Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used

with another battery pack.

■ Use power tools only with specifically designated

battery packs. Use of any other battery packs may

create a risk of injury and fire.

■ When battery pack is not in use, keep it away

from other metal objects like paper clips, coins,

keys, nails, screws, or other small metal objects

that can make a connection from one terminal to

another. Shorting the battery terminals together may

cause burns or a fire.

■ Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation or

burns.

SERVICE

■ Have your power tool serviced by a qualified repair

person using only identical replacement parts.

This will ensure that the safety of the power tool

is maintained.

SPECIAL RULES

■ Wear ear protectors with impact drills. Exposure

to noise can cause hearing loss.

■ Use auxiliary handles supplied with the tool (for

CHI-1442/CHI-1802 only). Loss of control can cause

personal injury.

CHARGER SAFETY

■ To reduce risk of injury, charge only nickel-cadmium

type rechargeable batteries. Other types of batteries

may burst, causing personal injury and damage.

■ Do not expose charger to wet or damp conditions.

■ Use of an attachment not recommended or sold by

the battery charger manufacturer may result in a risk

of fire, electric shock, or injuries to person.

■ To reduce risk of damage to charger body and

cord, pull by charger plug rather than cord when

disconnecting charger.

■ Make sure cord is located so that it will not be stepped

on, tripped over, or otherwise subjected to damage

and stress.

■ An extension cord should not be used unless

absolutely necessary. Use of improper extension

cord could result in a risk of fire and electric shock.

If extension cord must be used, make sure:

a. That pins on plug of extension cord are the same

number, size and shape as those of plug on charger.

b. That extension cord is properly wired and in good

electrical condition.

■ Do not operate charger with a damaged cord or

plug. If damaged, have it replaced immediately by a

qualified serviceman.

■ Do not operate charger if it has received a sharp

blow, been dropped, or otherwise damaged in any

way; take it to a qualified serviceman.

■ Do not disassemble charger; take it to a qualified

serviceman when service or repair is required.

Incorrect reassembly may result in a risk of electric

shock or fire.

■ To reduce risk of electric shock, unplug the charger

from outlet before attempting any maintenance or

cleaning. Turning off controls will not reduce this risk.

■ Disconnect charger from power supply when not in use.

■ Risk of electric shock. Do not touch uninsulated portion

of output connector or uninsulated battery terminal.

■ Save these instructions. Refer to them frequently and

use them to instruct others who may use this unit.

If you loan someone this unit, loan them these

instructions also.

9

GB

English

F

D

E I

P NL

S DK N FIN GR

H CZ RUS PL

RO

SLO TR

HR

960931224-01B.indd 9960931224-01B.indd 9 7/20/07 11:16:38 AM7/20/07 11:16:38 AM

SPECIFICATIONS

Model CHD-1442 CHI-1442

Voltage 14.4V 14.4V

Chuck(mm) 2-13 2-13

Switch Variable speed Variable speed

No load speed(drill mode):

-Lo speed(min

-1

) 0-400 0-400

-Hi speed(min

-1

) 0-1400 0-1400

No load speed(impact mode):

-Lo speed(min

-1

) 0-5200

-Hi speed(min

-1

) 0-18200

Max Torque(Nm) 34 34

Battery pack BPP-1413/ BPP-1413/

BPP-1415/ BPP-1415/

BPP-1417 BPP-1417

Charger BC-1440/ BC-1440/

BC-1415-S BC-1415-S

Model CHP-1802 CHI-1802

Voltage 18V 18V

Chuck(mm) 2-13 2-13

Switch Variable speed Variable speed

No load speed(drill mode):

-Lo speed(min

-1

) 0-440 0-440

-Hi speed(min

-1

) 0-1600 0-1600

No load speed(impact mode):

-Lo speed(min

-1

) 0-5720

-Hi speed(min

-1

) 0-20800

Max Torque(Nm) 37 37

Battery pack BPP-1813/ BPP-1813/

BPP-1815/ BPP-1815/

BPP-1817 BPP-1817

Charger BC-1800/ BC-1800/

BC-1815-S BC-1815-S

DESCRIPTION

1. Keyless chuck

2. Torque adjustment ring

3. Switch trigger

4. Gear train(High-Low)

5 . Quick mode selector

6. Direction of rotation selector(forward/reverse/center

lock)

7. Bit storage area(s)

8. Magnetic bit holder storage

9. Magnetic tray

10. Magnetic bit holder

11. Battery pack

12. Latches

13. Depress latches to release battery pack

14. Forward

15. Reverse

16. High speed

17. Low speed

18. Drive mode

19. Drill mode (torque adjustment not active)

20. Impact mode

21. Chuck jaws

22. Lock(tighten)

23. Unlock (release)

24. Drill bit(not included)

25. Bit

26. To decrease torque

27. To increase torque

28. Notch

29. Ears

30. Plate

31. Depth stoprod clamp

32. Auxiliary handle assembly

33. Depth Gauge rod

34. Drilling depth

35. Battery Charger

36. Green Light

37. Red Light

OPERATION

LED FUNCTION OF CHARGER

LED WILL BE ON TO INDICATE STATUS OF

CHARGER AND BATTERY PACK

■ Red LED on = Fast charging mode.

■ Green LED on = Fully charged battery pack.

■ No LED on = Defective charge or battery pack.

CHARGING YOUR BATTERY PACK

The battery pack for your tool has been shipped in

a low charge condition to prevent possible problems.

Therefore, you should charge it prior to use.

Note: Batteries will not reach full charge the first time

they are charged. Allow several cycles for them to

fully charge.

TO CHARGE

■ Charge battery pack only with the charger provided.

■ Make sure power supply is normal house voltage,

230 volts, 50 Hz, AC only.

10

GB

English

F

D

E I

P NL

S DK N FIN GR

H CZ RUS PL

RO

SLO TR

HR

960931224-01B.indd 10960931224-01B.indd 10 7/20/07 11:16:39 AM7/20/07 11:16:39 AM

OPERATION

■ Connect charger to power supply.

■ Place battery pack in charger. Align raised rib on

battery pack with groove in charger.

■ Press down on battery pack to be sure contacts on

battery pack engage properly with contacts in charger.

When properly connected, red light will turn on.

■ When your battery pack becomes fully charged, the

red light will turn off and the green light will turn on.

■ After normal usage, 1 hour of charge time is required

to be fully charged. A minimum charge time of 1 to

1-1/2 hours is required to recharge a completely

discharged tool.

■ DO NOT place charger in an area of extreme heat

or cold. It will work best at temperatures above 10°C

and below 38°C

IMPORTANT INFORMATION FOR RECHARGING HOT

BATTERIES

When using your tool continuously, the batteries in your

battery pack will become hot. You should let a hot battery

pack cool down for approximately 30 minutes before

attempting to recharge.

TO INSTALL BATTERY PACK (Fig.2)

■ Place the direction of rotation selector in center

position.

■ Place the battery pack in the tool. Align raised rib on

battery pack with groove in the tool’s battery port.

■ Make sure the latches on each side of the battery

pack snap in place and that battery pack is secured in

the tool before beginning operation.

TO REMOVE BATTERY PACK (Fig.2)

■ Place the direction of rotation selector in center

position.

■ Locate latches on side of battery pack and depress

both sides to release battery pack.

■ Remove battery pack from the tool.

SWITCH TRIGGER (Fig.3)

■ To turn the drill ON, depress the switch trigger.

■ To turn it OFF, release the switch trigger.

VARIABLE SPEED

The variable speed switch trigger delivers higher speed

and torque with increased trigger pressure and lower

speed with decreased trigger pressure.

SWITCH LOCK (Fig. 3)

The switch trigger can be locked in the OFF position.

This feature can be used to prevent the possibility of

accidental starting when not in use. To lock switch trigger,

place the direction of rotation selector (Forward/Reverse

Selector) in center position.

Note: When selector is in center position, switch trigger

is locked.

REVERSIBLE (Fig. 3)

The direction of bit rotation is reversible and is controlled

by a selector located above the switch trigger. With the

drill held in normal operating position, the direction of

rotation selector should be positioned to the left of the

switch trigger for drilling. The drilling direction is reversed

when the selector is to the right of the switch trigger. To

stop the drill, release the switch trigger and allow the

chuck to come to a complete stop.

ADJUSTING THE SPEED (Fig. 4)

Follow these steps to adjust the speed.

■ For high speed: Slide the two-speed gear train switch

to “2”.

■ For low speed: Slide the two-speed gear train switch

to “1”.

Note: If you have difficulty changing from one gear

range to the other, turn the chuck by hand until the gears

engage.

CAUTION

To prevent gear damage, always allow chuck to

come to a complete stop before changing the

speed or the direction of rotation.

QUICK MODE SELECTOR (CHD-1442/CHP-

1802 Fig.5 / CHI-1442/CHI-1802 Fig.6)

The Quick Mode Selector allows you to quickly switch

from drill mode to drive mode.

In general, drill mode should be used for drilling and

other heavy duty applications. Drive mode should be

used for driving screws. Impact mode should be used for

impact drilling.

11

GB

English

F

D

E I

P NL

S DK N FIN GR

H CZ RUS PL

RO

SLO TR

HR

960931224-01B.indd 11960931224-01B.indd 11 7/20/07 11:16:39 AM7/20/07 11:16:39 AM

OPERATION

SELECTING DRIVE OR DRILL SETTING

Using the chart below, choose correct speed and mode

the type of bit, fastener, and material you will be using.

APPLICATION

CHD-1442/

CHP-1802

Fig.5

CHI-1442/

CHI-1802

Fig.6

Lag screws up to 9.5 mm dia.

by 38mm long

Concr

ete screws

1/LOW

2/HIGH

Drill bits up to 6.35 mm

Self tapping scews

2/HIGH 1/L

OW

Deck or wood screws up to

50

mm

Small

screws or delicate work

that

requires more control

1/L

OW 2/HIGH

Deck or wood screws #8 up to

25

mm

Scre

ws for rough work where

spee

dismoreimportantthan

prec

ise control

2/HIGH

1/LOW

2/HIGH

KEYLESS CHUCK (Fig.7)

The drill has a keyless chuck to tighten or release drill

bits in the chuck jaws. The arrows on the chuck indicate

which direction to rotate the chuck body in order to LOCK

(tighten) or UNLOCK (release) the drill bit.

WARNING

Do not hold the chuck body with one hand and

use the power of the drill to tighten the chuck

jaws on the drill bit. The chuck body could slip in

your hand, or your hand could slip and come in

contact with the rotating drill bit. This could cause

an accident resulting in serious personal injury.

INSTALLING BITS (Fig.7) / MAGNETIC BIT

HOLDER (Fig.8)

■ Lock the switch trigger by placing the direction of

rotation selector in the center position.

■ Open or close the chuck jaws to a point where the

opening is slightly larger than the bit size or the end

of the magnetic bit holder. Also, raise the front of the

drill slightly to keep the bit /bit holder from falling out

of the chuck jaws.

■ Insert the drill bit/bit holder.

■ Tighten the chuck jaws on the drill bit/bit holder

■ Insert a bit into the open end of the bit holder if

applicable.

REMOVING BITS (Fig.7) / MAGNETIC BIT

HOLDER (Fig.8)

■ Lock the switch trigger by placing the direction of

rotation selector in the center position.

■ Rotate the chuck sleeve clockwise to open the chuck

jaws.

■ Remove the drill bit/bit holder.

ADJUSTING THE TORQUE (Fig.9)

When using the drill-driver for various driving applications,

it becomes necessary to increase or decrease the torque

in order to help prevent the possibility of damaging

screw heads, threads, workpiece, etc. In general, torque

intensity should correspond to the screw diameter. If the

torque is too high or the screws too small, the screws

may be damaged or broken.

The torque is adjusted by rotating the torque adjustment

ring.

The torque is greater when the torque adjustment ring

is set on a higher setting. The torque is less when the

torque adjustment ring is set on a lower setting.

The proper setting depends on the type of material and

the size of screw you are using.

ADJUSTING THE POSITION OF THE

AUXILIARY HANDLE ASSEMBLY (FOR CHI-

1442/CHI-1802 ONLY) (Fig.10)

To adjust the position of the auxiliary handle assembly.

■ Loosen the handle assembly by turning the handle

counterclockwise.

■ Insert the auxiliary handle assembly in the desired

operating position.

■ Securely tighten by turning the auxiliary handle

clockwise.

12

GB

English

F

D

E I

P NL

S DK N FIN GR

H CZ RUS PL

RO

SLO TR

HR

960931224-01B.indd 12960931224-01B.indd 12 7/20/07 11:16:39 AM7/20/07 11:16:39 AM

13

GB

English

F

D

E I

P NL

S DK N FIN GR

H CZ RUS PL

RO

SLO TR

HR

OPERATION

ADJUSTING THE DEPTH STOP ROD (FOR CHI-

1442/CHI-1802M ONLY) (Fig.11)

The depth stop rod helps control the depth of drilled

holes.

■ Lock the switch trigger by placing the direction of

rotation selector in the center position.

■ Loosen the auxiliary handle assembly by turning the

knob counterclockwise.

■ Adjust the depth stop rod so that the drill bit extends

beyond the end of the rod to the required drilling

depth.

■ Tighten the auxiliary handle assembly by turning the

knob clockwise.

MAINTENANCE

WARNING

When servicing, use only identical Ryobi

replacement parts. Use of any other parts may

create a hazard or cause product damage.

Avoid using solvents when cleaning plastic parts. Most

plastics are susceptible to damage from various types of

commercial solvents and may be damaged by their use.

Use clean cloths to remove dirt, dust, oil, grease, etc.

WARNING

Do not at any time let brake fluids, gasoline,

petroleumbased products, penetrating oils, etc.,

come in contact with plastic parts. Chemicals can

damage, weaken or destroy plastic which may

result in serious personal injury.

Do not abuse power tools. Abusive practices can damage

tool as well as workpiece.

WARNING

Do not attempt to modify this tool or create

accessories not recommended for use with this

tool. Any such alteration or modification is misuse

and could result in a hazardous condition leading

to possible serious personal injury.

ENVIRONMENTAL PROTECTION

Recycle raw materials instead of disposing as

waste.

The machine, accessories and packaging

should be sorted for environmental-friendly

recycling.

960931224-01B.indd 13960931224-01B.indd 13 7/20/07 11:16:39 AM7/20/07 11:16:39 AM

Page is loading ...

GARANTIE - CONDITIONS

Ce produit Ryobi est garanti contre les vices de fabrication et les pièces

défectueuses pour une durée de vingt-quatre (24) mois, à compter de

la date faisant foi sur l'original de la facture établie par le revendeur à

l'utilisateur final.

Les détériorations provoquées par l'usure normale, par une utilisation ou

un entretien anormal ou non autorisé, ou par une surcharge sont exclues

de la présente garantie de même que les accessoires tels que batteries,

ampoules, lames, embouts, sacs, etc.

En cas de mauvais fonctionnement au cours de la période de garantie,

veuillez envoyer le produit NON DÉMONTÉ avec la preuve d'achat à votre

fournisseur ou au Centre Service Agréé Ryobi le plus proche de chez

vous.

Vos droits légaux se rapportant aux produits défectueux ne sont pas remis

en cause par la présente garantie.

WARRANTY - STATEMENT

All Ryobi products are guaranteed against manufacturing defects and

defective parts for a period of twenty four (24) months from the date

stated on the original invoice drawn up by the retailer and given to the

end user.

Deterioration caused by normal wear and tear, unauthorised or improper

use or maintenance, or overload are excluded from this guarantee as are

accessories such as battery packs, light bulbs, blades, fittings, bags, etc.

In the event of malfunction during the warranty period, please take the

NON-DISMANTLED product, along with the proof of purchase, to your

retailer or nearest Authorised Ryobi Service Centre.

This warranty in no way affects your legal rights concerning defective

products.

GARANTIE - BEDINGUNGEN

Für alle Ryobi-Produkte gilt eine Garantie gegen Material- und

Verarbeitungsfehler für einen Zeitraum von vierundzwanzig (24)

Monaten ab dem Datum der vom Wiederverkäufer für den Endbenutzer

ausgestellten Originalrechnung.

Fehler, die auf Grund einer normalen Abnutzung, einer unberechtigten oder

falschen Wartung oder Handhabung oder durch eine Überbelastung auftreten,

sind von der Garantie ausgeschlossen. Dies gilt auch für Zubehörteile wie

Batterien, Glühbirnen, Sägeblätter, Ansatzstücke, Beutel usw.

Senden Sie das Produkt im Fall eines Defekts innerhalb des

Garantiezeitraumes in NICHT ZERLEGTEM Zustand zusammen

mit dem Kaufnachweis an Ihren Händler oder Ihr nächstes Ryobi-

Kundendienstzentrum zurück.

Diese Garantie hat keine Auswirkungen auf Ihre gesetzlichen Rechte in

Bezug auf fehlerhafte Produkte.

GARANTÍA - CONDICIONES

Este producto Ryobi está garantizado contra los defectos de fabricación

y las piezas defectuosas por un período de veinticuatro (24) meses, a

partir de la fecha que figura en el original de la factura establecida por el

distribuidor al usuario final.

Se excluyen de la presente garantía los deterioros provocados por

un desgaste normal, una utilización o mantenimiento incorrecto o no

autorizado, y una sobrecarga, así como los diversos accesorios: baterías,

bombillas, hojas, puntas, bolsas, etc.

En caso de funcionamiento incorrecto durante el período de la garantía, envíe

el producto SIN DESMONTAR con la prueba de compra a su proveedor o al

Centro de Servicio Acreditado Ryobi más cercano a su domicilio.

Los derechos legales relacionados con los productos defectuosos no son

cuestionados por la presente garantía.

GARANZIA - CONDIZIONI

Questo prodotto Ryobi è garantito contro tutti i difetti di fabbricazione e

pezzi difettosi per una durata di ventiquattro (24) mesi, a partire dalla data

indicata sull’originale della fattura compilata dal rivenditore e consegnata

all’utente finale.

Il deterioramento provocato dall’usura normale, da un utilizzo o una

manutenzione non conformi o non autorizzati, o da un sovraccarico,

è escluso dalla presente garanzia. La garanzia è esclusa anche per gli

accessori come batterie, lampadine, lame, punte, borse, ecc.

In caso di malfunzionamento nel corso del periodo di garanzia, riportare

il prodotto NON SMONTATO corredato della prova d’acquisto al fornitore

o al più vicino Centro di Assistenza Autorizzato Ryobi.

I diritti legali relativi ai prodotti difettosi non sono rimessi in causa dalla

presente garanzia.

GARANTIA - CONDIÇÕES

Este produto Ryobi está garantido contra os vícios de fabrico e as peças

defeituosas por um prazo de vinte e quatro (24) meses, a contar da

data que faz fé no original da factura emitida pelo vendedor ao utilizador

final.

As deteriorações provocadas pelo desgaste normal, por uma utilização

ou uma manutenção anormal ou não autorizada, ou por uma sobrecarga

ficam excluídas da presente garantia assim como os acessórios tais como

baterias, lâmpadas, lâminas, ponteiras, sacos, etc.

No caso de mau funcionamento durante o período de garantia, queira

enviar o produto NÃO DESMONTADO com a prova de compra ao seu

fornecedor ou ao Centro de Serviço Autorizado Ryobi mais próximo.

Os seus direitos legais relativos aos produtos defeituosos não são

prejudicados pela presente garantia.

GARANTIEVOORWAARDEN

Dit Ryobi product is gewaarborgd tegen fabricagefouten en defecte

onderdelen gedurende een periode van vierentwintig (24) maanden,

te rekenen vanaf de officiële datum op het origineel van de door de

wederverkoper aan de eindgebruiker uitgeschreven rekening.

Beschadigingen veroorzaakt door normale slijtage, door abnormaal of

ongeoorloofd gebruik of onderhoud, of door overbelasting vallen niet

onder deze garantie, evenmin als accu's, lampen, bits, snijbladen,

zakken enz.

In geval van slechte werking tijdens de garantieperiode, wordt u verzocht

het NIET GEDEMONTEERDE product samen met de koopbon aan uw

leverancier of aan het dichtstbijzijnde Ryobi servicecentrum te sturen.

Deze garantie doet niet af aan uw wettelijke rechten met betrekking tot

defecte producten.

GARANTI - VILLKOR

Ryobi garanterar denna produkt mot fabrikationsfel och defekta delar

under tjugofyra (24) månader, räknat från det datum som anges

på originalfakturan fastställd av återförsäljaren och överlämnad till

slutanvändaren.

Denna garanti täcker inte skador som förorsakas av normalt slitage,

av onormal eller otillåten användning eller skötsel, eller av överbelastning.

Den täcker inte heller tillbehör som batterier, glödlampor, blad, ändstycken,

påsar, osv.

I händelse av felaktig funktion medan garantin är i kraft skall produkten

sändas UTAN ATT DEMONTERAS tillsammans med inköpsbeviset

till leverantören eller till närmaste servicecenter som auktoriserats av

Ryobi.

De rättigheter som lagen ger i förhållande till defekta produkter ifrågasätts

inte av denna garanti.

I tilfælde af driftsfejl i garantiperioden skal produktet afleveres IKKE

DEMONTERET med købebevis til forhandleren eller nærmeste autoriserede

Ryobi serviceværksted.

De lovbestemte rettigheder i forbindelse med defekte produkter forringes

ikke af denne reklamationsret.

F

GB

D

E

I

P

NL

S

960931224-01B.indd 131960931224-01B.indd 131 7/20/07 11:17:14 AM7/20/07 11:17:14 AM

Page is loading ...

S

DK

N

FIN

F

GB

D

E

I

P

NL

CHD-1442/CHP-1802 CHI-1442/CHI-1802

Niveau de pression acoustique (71+3) dB(A) (89+3) dB(A)

Niveau de puissance acoustique (82+3) dB(A) (100+3) dB(A)

Niveau de vibrations

1.56 m/s

2

16.17 m/s

2

Sound pressure level (71+3) dB(A) (89+3) dB(A)

Sound power level (82+3) dB(A) (100+3) dB(A)

Vibration level 1.56 m/s

2

16.17 m/s

2

Schalldruckpegel (71+3) dB(A) (89+3) dB(A)

Schallleistungspegel (82+3) dB(A) (100+3) dB(A)

Vibrationspegel 1.56 m/s

2

16.17 m/s

2

Nivel de presión acústica (71+3) dB(A) (89+3) dB(A)

Nivel de potencia acústica (82+3) dB(A) (100+3) dB(A)

Nivel de vibraciones 1.56 m/s

2

16.17 m/s

2

Livello di pressione acustica (71+3) dB(A) (89+3) dB(A)

Livello di potenza acustica (82+3) dB(A) (100+3) dB(A)

Livello di vibrazioni 1.56 m/s

2

16.17 m/s

2

Nível de pressão acústica (71+3) dB(A) (89+3) dB(A)

Nível de potência acústica (82+3) dB(A) (100+3) dB(A)

Nível de vibrações 1.56 m/s

2

16.17 m/s

2

Geluidsdrukniveau (71+3) dB(A) (89+3) dB(A)

Geluidsvermogensniveau (82+3) dB(A) (100+3) dB(A)

Trillingenniveau 1.56 m/s

2

16.17 m/s

2

Ljudtrycksnivå (71+3) dB(A) (89+3) dB(A)

Ljudeffektnivå (82+3) dB(A) (100+3) dB(A)

Vibrationsnivå 1.56 m/s

2

16.17 m/s

2

Lydtryksniveau (71+3) dB(A) (89+3) dB(A)

Lydstyrkeniveau (82+3) dB(A) (100+3) dB(A)

Vibrationsniveau 1.56 m/s

2

16.17 m/s

2

Lydtryrkknivå (71+3) dB(A) (89+3) dB(A)

Lydstyrkenivå (82+3) dB(A) (100+3) dB(A)

Vibrasjonsnivå 1.56 m/s

2

16.17 m/s

2

Äänenpainetaso (71+3) dB(A) (89+3) dB(A)

Äänen tehotaso (82+3) dB(A) (100+3) dB(A)

Värähtelytaso 1.56 m/s

2

16.17 m/s

2

960931224-01B.indd 134960931224-01B.indd 134 7/20/07 11:17:15 AM7/20/07 11:17:15 AM

Page is loading ...

F

GB

D

E

P

NL

S

DK

N

FIN

GR

DÉCLARATION DE CONFORMITÉ

Nous déclarons sous notre propre responsabilité que ce produit

est en conformité avec les normes ou documents normalisés

suivants: