2. Amico
  3. 3-23-000607
3-23-000607

Amico 3-23-000607 Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Amico 3-23-000607 Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • How to install the faceplate?
    What is the first step of installation?
    Which connection should be made first?
    What should be done to avoid the risk of shock?
    Where can I find more information about available collection facilities?
Installation Guide
1
MRI Compatible
Important Safety Instructions
When using electrical equipment, basic safety precautions should always
be followed including the following:
Read And Follow All Safety Instructions
RGB Wall Mounted Touch Controller
3-23-000607
Installation:
Diagram 1
Save These Instructions For Future Reference
1. Warning: This product must be installed in accordance with the NEC or your
local electrical code. If you are not familiar with these codes and require-
ments, consult a qualied electrician. Aenon: Ce produit doit être installé
conformément au NEC ou à votre code électrique local. Si vous n’êtes pas fami-
lier avec ces codes et exigences, consultez un électricien qualié.
2. Warning: This equipment is not for use in hazardous combusble atmospheres
as dened by the Naonal Electrical Code. Averssement: Cet équipement ne
doit pas être ulisé dans des atmosphères combusbles dangereuses telles que
dénies par le Naonal Electrical Code.
3. Danger: Risk of shock - Disconnect power before installaon. Danger: Risque
de choc – Couper l’alimentaon avant l’installaon.
METRIC-MILLIMETER
TOLERANCES
UNLESS OTHERWISE
SPECIFIED
X ± 0.8
X.X ± 0..25
X.XX ± 0.13
X.XXX ± 0.013
ANGLES ±1/2°
DRAWING NO.
SCALE
JOB NUMBER
DESCRIPTION
DRAWN BY
CHECKED BY
DRAWN DATE
CHECKED DATE
REVISION DATE
REVISION DESCRIPTION
ECN
SHEET
This document and the information contained therein are the property of PDC FACILITIES, INC. Hartland, Wisconsin.
Recipient agrees NOT to:
(1) Use such information for purposes other than those expressly authorized by PDC FACILITIES, INC. (2) Furnish such information to any other person
in whole or in part for any purpose whatsoever without the express written permission of PDC FACILITIES, INC.
(3) Reproduce or copy this document either in whole or in part without the express written permission of PDC FACILITIES, INC.
FACILITIES, INC.
700 WALNUT RIDGE DRIVE
HARTLAND, WI 53029
PHONE: (262) 367-7700
FAX: (262) 367-7944
of
REVISION
1:2
0
1
3-23-000607
PP-ELE VAYA TOUCH CONTROLLER
1
INCH
TOLERANCES
UNLESS OTHERWISE
SPECIFIED
X.X ± 0.03
X.XX ± 0.015
X.XXX ± 0.005
X.XXXX ± 0.0005
ANGLES ±1/2°
DRAWING NO.
SCALE
JOB NUMBER
DESCRIPTION
DRAWN BY CHECKED BY
DRAWN DATE
CHECKED DATE
REVISION DATE
REVISION DESCRIPTION
ECN
SHEET
This document and the information contained therein are the property of PDC FACILITIES, INC. Hartland, Wisconsin.
Recipient agrees NOT to:
(1) Use such information for purposes other than those expressly authorized by PDC FACILITIES, INC. (2) Furnish such information to any other person
in whole or in part for any purpose whatsoever without the express written permission of PDC FACILITIES, INC.
(3) Reproduce or copy this document either in whole or in part without the express written permission of PDC FACILITIES, INC.
FACILITIES, INC.
700 WALNUT RIDGE DRIVE
HARTLAND, WI 53029
PHONE: (262) 367-7700
FAX: (262) 367-7944
of
REVISION
1:4
0
1
3-23-000607 STEP 2
PP-ELE VAYA TOUCH CONTROLLER
1
Diagram 2
Diagram 4 Diagram 3
Step 1:
Turn off the main power supply.
Step 2:
Remove the faceplate by removing the two
screws as shown in Diagram 1.
Step 3:
Attach the backplate to the installed junction
box as shown in Diagram 2.
Step 4:
Connect the plug as shown in Diagram 3.
Step 5:
Attach the faceplate as shown in Diagram 4.
Step 6:
Complete the electrical connections as shown
in the Electrical Connections Section.
2
Directive 2012/19/EU (WEEE - Waste Electrical and Electronic Equipment): Information for Users
This product complies with EU Directive 2012/19/EU. The crossed out wheeled bin symbol on the article means that at the end of its useful lifespan, this product must not be disposed
of with your other household or municipal waste. This product has required the extraction and use of natural resources for its production. It may contain hazardous substances that
could impact health and the environment if not properly disposed. In order to avoid dissemination of those substances in our environment and to diminish the pressure on the natural
resources, the user is responsible for delivering the appliance to an appropriate collection facility at the end of its useful lifespan. The separate collection and recycling of your waste
equipment at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information
on available collection facilities contact your local waste collection service or the place of purchase.
Amico Lights Corporation | 122-B East Beaver Creek Road, Richmond Hill, ON L4B 1G6, Canada | www.amico.com
Toll Free Tel: 1.877.462.6426 | Toll Free Fax:1.866.440.4986 | Tel: 905.764.0800 | Fax: 905.764.0862
For informational purposes only. Content is subject to change.
ALT-INSTALL-MRI-TOUCH-CONTROLLER-RGB 01.18.2021
Back of Touch Controller
Removable back of
Touch Controller
12V+
DMX+
DMX-
GND
Electrical Connections
Diagram 5
Step 1:
Make the following connections as shown in Diagram 5.
/