Laser Ford 2.0 EcoBlue TDCi Operating instructions

Brand: Laser

Model: Ford 2.0 EcoBlue TDCi

Category: Car kits

Type: Operating instructions

Laser Ford 2.0 EcoBlue TDCi is a pulley puller kit designed for the latest Ford 2.0L EcoBlue TDCi engines with a "belt in oil" design. It allows for the removal of the front pulley, which often requires force, by connecting to the inner part of the pulley to prevent damage to the rubber component. The kit includes a crankshaft protector spigot, puller bridge, bolts and washer, and a force screw. It is suitable for use on various Ford models and engine codes, as specified in the instruction manual.

Part No. 7334

www.lasertools.co.uk

Vibration Damper

Pulley Puller

Ford 2.0 EcoBlue TDCi

Instructions

Ref. Code OEM Ref. Description

AC866 204-158-01* Crankshaft Protector Spigot

C867 205-295*

Puller Bridge

CBolts and Washer x 2

DForce Screw

Components

Introduction

This Pulley Puller kit has been designed for the latest Ford 2.0L

EcoBlue TDCi engine which features an innovative “belt in oil”

design where the synchronous drive belt is sited inside the

oiled area of the engine. In order to gain access to the timing

belt area of these engines it is necessary to remove the front

pulley which often requires some force.

The tool does this by connecting to the inner part of the pulley

which ensures no damage to the rubber component of the

pulley.

For timing belt replacement see Laser 7323.

*NOTE: Performs the function of OEM 205-295 (puller) and

204-158-01 (crankshaft nose protector spigot) for the

applications listed only.

The following instructions are for guidance only. Please refer

to OEM derived data such as the vehicle manufacturers’ own

data or Autodata.

The use of this kit is purely down to the user’s discretion

and Tool Connection Ltd. cannot be held responsible for any

damage caused what so ever.

Applications

Engine Codes

BCCA, BCCB, BCCC, BCDA, YLCA, YLCB, YLCC, YLDA, YLDC, YLF6,

YLFA*, YLFB*, YLFS, YLR6, YMCA, YMCB, YMCC, YMDA, YMF6,

YMFA*, YMFB*, YMFS, YMR6, YNCA, YNF6, YNFA*, YNFB*, YNFS,

YNR6

www.lasertools.co.uk

Always refer to the website for most up to date applications:

www.lasertools.co.uk/product/7334

Make Model Year Type

Ford Edge 2018 - 21 2.0 EcoBlue TDCi

Focus 2018 - on

Focus Active 2019 - on

Galaxy 2018 - 21

Kuga 2019 - on

Mondeo 2019 - 21

S-MAX 2018 - 21

Transit 2016 - on

Transit Custom 2016 - on

Tourneo Custom 2016 - on

*NOTE: Some Transit use Laser Part No. 8394 (OEM 303-1657).

Safety Warnings - PLEASE READ

• Personal protection and safety equipment must be used at

all times. Eye protection and protective gloves must be worn

when using these tools.

• Misuse of tools is unsafe,and can cause engine damage.

• Remove damaged tools from use.

• Store in a dry place when not in use.

Warning:

Only to be used with hand tools.

The threaded force screw must be kept clean and lubricated

with Molybdenum Disulphide grease. Failure to adequately

lubricate the force screw and frame may result in damage

which will affect the product warranty.

4 5

Where Used

Preparation

• Remove starter motor and install ﬂywheel locking tool.

• Remove auxiliary drive belt.

Important Notes

• Water pump “stretchy” auxiliary drive belt once removed

should not be re-used.

• Mark position of RH engine mounting before removal.

• Replacement of the timing belt also requires replacement of

the tensioner and cover.

• For Engine Timing Tool use Laser 7323.

www.lasertools.co.uk www.lasertools.co.uk

Instructions

Component A – Crankshaft Protector Spigot

Component A is used to protect the end of the crankshaft from

the forces of the force screw.

With the crankshaft pulley bolt (1) and auxiliary drive belt (2)

removed insert the crankshaft protector spigot (A) into the end

of the crankshaft.

NOTE: The crankshaft retaining bolt must be replaced.

Component B, C and D – Pulley Puller Assembly

Components B, C and D are used to push against component A

to pull the pulley off.

Assemble B, C and D as shown in Fig.2.

• Ensure the force screw (D) is well lubricated with

Molybdenum Disulphide grease at the points shown in Fig.2.

• Ensure the holding bolts (C) are evenly tightened and that

the force screw (D) sits square and on the centre of the

spigot (A).

• Wind the force screw in to pull the pulley off.

Fig.1

Fig.2

Instructions

www.lasertools.co.uk www.lasertools.co.uk

Our products are designed to be used correctly and with care for

the purpose for which they are intended. No liability is accepted by

the Tool Connection for incorrect use of any of our products, and

the Tool Connection cannot be held responsible for any damage to

personnel, property or equipment when using the tools. Incorrect use

will also invalidate the warranty.

If applicable, the applications database and any instructional

information provided has been designed to offer general guidance for

a particular tool’s use and while all attention is given to the accuracy

of the data no project should be attempted without referring ﬁrst to

the manufacturer’s technical documentation (workshop or instruction

manual) or the use of a recognised authority such as Autodata.

It is our policy to continually improve our products and thus we

reserve the right to alter speciﬁcations and components without prior

notice. It is the responsibility of the user to ensure the suitability of

the tools and information prior to their use.

www.lasertools.co.uk

7334_Instructions_V6

Laser Ford 2.0 EcoBlue TDCi Operating instructions

Brand: Laser

Model: Ford 2.0 EcoBlue TDCi

Category: Car kits

Type: Operating instructions

Download PDF

report

Laser Ford 2.0 EcoBlue TDCi Operating instructions

Laser Ford 2.0 EcoBlue TDCi Operating instructions

Related papers

Other documents