VISUAL COMFORT PB 5030 is a stunning medium ring chandelier that adds a touch of elegance to any room. This versatile fixture can be mounted upright or inverted, making it suitable for a variety of spaces. With its adjustable rods, you can customize the hanging height to fit your needs. The chandelier features a durable metal construction with a beautiful finish and comes with all the necessary hardware for easy installation.
VISUAL COMFORT PB 5030 is a stunning medium ring chandelier that adds a touch of elegance to any room. This versatile fixture can be mounted upright or inverted, making it suitable for a variety of spaces. With its adjustable rods, you can customize the hanging height to fit your needs. The chandelier features a durable metal construction with a beautiful finish and comes with all the necessary hardware for easy installation.
Overture Medium Ring Chandelier
Item # PB 5030
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
NOTICE:
US
M
L
I
D
S
E
T
Phillips Screwdriver Slotted Screwdriver Wire Strippers
1. Carefully remove all parts from the box. Place on a clean, soft surface.
2. Remove mounting plate (C) from canopy (J) by removing collar
ring (Y).
3. Remove mounting plate bracket (H) from mounting plate (C) by
removing screws (B).
4. Install mounting plate (C) to the junction box and secure with mounting
screws (D).
5. Connect supply ground wire (usually green or bare copper) around the
green grounding screw (see diagram 1). Tighten.
NOTE: It is imperative that the fixture is grounded.
6. Connect driver (E) input neutral wire (white) to the supply neutral wire
(usually white) using wire nut (A).
7. Connect driver (E) input hot wire (black) to the supply hot wire (usually
black) using wire nut (A).
CAUTION: Do not reverse the hot and neutral connections.
8. Make sure all wire connections are tight, then carefully tuck into the
junction box.
9. Place driver (E) onto the mounting plate bracket (H), then install to
mounting plate (C) and secure with screws (B).
10. Feed electrical wire through bottom rod (Z) and thread to hub (O).
Repeat for middle rod (M), connecting to bottom rod (N).
11. Continue feeding wire through collar ring (Y), canopy (J) and top
rod (K).
F
F
G
G
D
C
B
A
A
H
H
I
E
P
Q
R
S
I
J
K
Y
M
Z
O
Diagram 1
Diagram 2
Overture Medium Ring Chandelier
Item # PB 5030
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
NOTICE:
US
M
L
I
D
S
E
T
12. Holding fixture upright, slide collar ring (Y) and canopy (J) down and
rest on hub (O). Then connect top rod (K) to middle rod (M).
NOTE: Slide components down slowly to avoid damages.
13. Hang fixture swivel ball (I) to center of bracket (H) and secure
with set screw (G) using provided wrench (F). See diagram 2.
14. Cut excess wire, being sure to leave enough to reach the junction
box.
15. Remove outer housing of wire by making a neat cut all the way
around, about 1” from the end. Make sure not to cut too deep or
electrical wires could be damaged underneath. Once cut is made,
remove and discard the 1” piece of housing off the end, exposing the
electrical wires.
16. Separate wire and strip insulation on each 5/8".
17. Connect fixture neutral wire (black) to driver (E) output wire (black)
using wire nut (A).
18. Connect fixture hot wire (red) to driver (E) output wire (red) using wire
nut (A).
CAUTION: Do not reverse the hot and neutral connections.
19. Install canopy (J) to mounting plate bracket (H) and secure with collar
ring (Y).
20. Thread rods (S) to fixture body (P).
21. Remove protective covers (R) from socket, then thread shades (Q)
to sockets.
NOTE: Do not overtighten otherwise shade could become damaged.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do
not use abrasive or chemical agents.
F
F
G
G
D
C
B
A
A
H
H
I
E
P
Q
R
S
I
J
K
Y
M
Z
O
Diagram 1
Diagram 2
Overture Medium Ring Chandelier
Item # PB 5030
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
NOTICE:
Z
O
T
T
W
P
X
XS
S
U
U
V
V
N L
Z
V
Y
T
O
N L
US
M
L
I
D
S
E
T
Inverted Installation:
1. Carefully remove all parts from the box. Place on a clean, soft surface.
2. Loosen set screw (S) using provided wrench (X), then unscrew
hub (O) from base (V). See diagram 3.
3. Loosen bottom screws on terminal block (T) and screws (Z) on cable
nut (Y), then remove wires and separate.
4. Loosen set screws (U) and remove cables (W) from base (V). Turn
fixture over, then re-assemble cables (W) to base (V), securing with
set screws (U).
5. Install cable nuts (Y) to end of hanging cables. Insert other end of
hanging cable (Y) through the cable lock and tighten screw ends (Z)
with a screwdriver to secure. See diagram 4.
6. Twist fixture neutral wires (black) together, then insert into terminal
block neutral (N) and secure screw. See diagram 4.
7. Twist fixture line wires (red) together, then insert into terminal block
line (L) and secure screw. See diagram 4.
8. Install hub (O) to hub base (V) and secure with set screw (S) using
provided wrench (X).
Care Instructions: Clean only with a soft dry cloth or feather duster. Do
not use abrasive or chemical agents.
Diagram 3
Diagram 4
-
1
-
2
-
3
VISUAL COMFORT PB 5030 is a stunning medium ring chandelier that adds a touch of elegance to any room. This versatile fixture can be mounted upright or inverted, making it suitable for a variety of spaces. With its adjustable rods, you can customize the hanging height to fit your needs. The chandelier features a durable metal construction with a beautiful finish and comes with all the necessary hardware for easy installation.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
VISUAL COMFORT PCD 2200 User manual
-
VISUAL COMFORT TOB 2730 User manual
-
VISUAL COMFORT S 2121 User manual
-
-
-
-
-
-
-
Other documents
-
circa LIGHTING PB 5045 User manual
-
circa LIGHTING PCD 5115 User manual
-
Visual Comfort Studio CHC 1474GI-NP Installation guide
-
Ralph Lauren RL 5685 User manual
-
-
circa LIGHTING PB 5151 Installation guide
-
-
circalighting ARN5500 Installation guide
-
-
