DECO-GLOW EDGE LIT UNDER CABINET LIGHT
DWSNCCT-L12 | DWSNCCT-L18 INSTRUCTION
Getting Started
1. Read these instructions in their
entirety before installing or using
this product.
WARNING
• This light may present a possible shock or fire hazard if not properly
installed. Products should be installed in accordance with these
instructions, current local electrical codes, and/or the National
Electric Code.
Installation
Tools Needed: Pencil, Philips Screwdriver, Drill, 1/16” Drill Bit, Tape Measure, Safety Glasses.
1. Locate a suitable 120V outlet to install this light to. This light includes a 5’ power cord with a polarized plug (one blade wider than the other) and must be
used in a polarized outlet. Do not use adapters or alter the plug.
2. Determine the location for your new light - the ideal position is underneath your cabinets, closer to the front of the cabinet, This generally provides the best
quality of light while allowing the edge lit panel to be seen while in operation.
3. Locate and mark the position of the mounting holes. You can directly mark your cabinet with the pencil. Position the mounting bracket in your desired
location and mark the screwholes through the bracket.
4. Drill 1/16” pilot holes, being careful not to drill completely through your cabinet.
5. Slide the light onto the mounting bracket using gentle pressure. Connect the power cord to the light. The power cord fits only into the side of the light
closest to the power buttons. Plug the cord into the power outlet. Do not conceal the cord inside walls, ceilings, soffit, kitchen cabinets, or other similar
permanent structures. Do not run the power cord through holes in walls, ceilings, or floors.
6. To interconnect multiple fixtures, repeat the above steps 2-4 for the new fixtures, and use the included 12” linking cable to connect the new light to the
primary light.
Warning: To avoid permanent fixture damage, link only up to 120 watts maximum. Do not mix and match models other than DWSNCCT-L12 or DWSNCCT-L18.
A. Power
Tap the power button to turn on the lights. Press and hold this button to dim
the lights
Warning: Do not disassemble or modify this light. Modification voids the manufacturer’s warranty and any applicable regulatory
certifications this light may possess.
Limited Warranty
Under normal use and conditions, AmerTac provides to the original purchaser of this product a one year limited express warranty that is set forth
in the Limited Warranty stated in full at www.amertac.com/warranties. The Limited Warranty is in lieu of all other express or implied warranties or
liabilities subject to the exceptions explained fully in the Limited Warranty on the website.
Thank you for your purchase of this under cabinet light. Unlike most under cabinet lights that are meant
to be hidden from view, this Deco-Glow light is meant to be seen when lit, with a transparent window
that extends beyond the front edge of your cabinet. Lit by a series of Edge-Lit LED’s, this light creates
a contemporary look in your home for a perfect balance of style and usability. When turned off, the
transparent window virtually disappears under your cabinet.
Includes
Light Fixture, 5’ Power Cord, 12” Linking Cord, Mounting Hardware & (2) Screws
©2021 AmerTac™
250 Boulder Drive
Breinigsville, PA 18031
amertac.com
Made in China
UC_TL_016_0721
Product SKU Size Weight Color Temperature Lumens CRI Linking Watts
DWSNCCT-L12 12.00”L x 1.60”W x 1.20”H 0.30 lbs 2700, 3000, 3500, 4000, 5000K 420lm
(at 100%) 80+ 120 Watts
Max
5.5
DWSNCCT-L18 18.00”L x 1.60”W x 1.20”H 0.60 lbs 2700, 3000, 3500, 4000, 5000K 620lm
(at 100%) 7.0
2. Do not mount this light over a
sink or a stove.
Operation
B. Color Temperature
Tap the “White Adjust” button to cycle white color temperatures from 2700K,
3000K, 3500K, 4000K and 5000K.
C. Power Off
Tap the power button to power off the light when finished using it.
Power Button
White Adjust
Button
