Laars MT2H0750NACK1CJX Installation guide

Brand: Laars

Model: MT2H0750NACK1CJX

Type: Installation guide

This manual is also suitable for

Installation and Operation Instructions Document 1211K

H2329100K

Hydronic Boiler

Model MT2H

Volume Water Heater

Model MT2V

Sizes 500–2000 MBTU/h

FOR YOUR SAFETY: This product must be installed and serviced by a professional service technician,

qualied in hot water boiler installation and maintenance. Improper installation and/or operation could

create carbon monoxide gas in ue gases which could cause serious injury, property damage, or death.

Improper installation and/or operation will void the warranty. For indoor installations, as an additional

measure of safety, Laars strongly recommends installation of suitable Carbon Monoxide detectors in the

vicinity of this appliance and in any adjacent occupied spaces.

Installation and Operation Instructions for

MIGHTY THERM2

WARNING

If the information in this manual is not followed

exactly, a re or explosion may result causing

property damage, personal injury or loss of life.

Do not store or use gasoline or other ammable

vapors and liquids in the vicinity of this or any

other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use

any phone in your building.

• Immediately call your gas supplier from a

nearby phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the

re department.

Installation and service must be performed by

a qualied installer, service agency, or gas supplier.

AVERTISSEMENT

Assurez-vous de bien suivres les instructions

données dans cette notice pour réduire au

minimum le risque d’incendie ou d’explosion ou

pour éviter tout dommage matériel, toute blessure

ou la mort.

Ne pas entreposer ni utiliser d’essence ni d’autres

vapeurs ou liquides inammables dans le voisinage

de cet appareil ou de tout autre appareil.

QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:

• Ne pas tenter d’allumer d’appareils.

• Ne touchez à aucun interrupteur. Ne pas vous servir des

téléphones dansle bâtiment où vous êtes.

• Appelez immédiatement votre fournisseur de

gaz depuis un voisin. Suivez les instructions du

fournisseur.

• Si vous ne pouvez rejoindre le fournisseur de gaz,

appelez le sservice des incendies.

L’installation et l’entretien doivent être assurés par un

installateur ou un service d’entretien qualié ou par le

fournisseur de gaz.

LAARS Heating Systems

Table of Contents

SECTION 1 General Information

1.A Introduction ....................................................... 1

1.B Warranty ........................................................... 1

1.C Model Identication ........................................... 2

1.D Safety Notes ..................................................... 3

1.E Locating the unit ............................................... 5

1.F Locating Pump-Mounted Water Heater

with Respect to Storage Tank(s) ....................... 5

1.G Locating Pump-Mounted Boiler

with Respect to Return/Supply Header ............ 5

1.H Locating the Unit for Correct Horizontal

Vent/Ducted Air Distance from Outside Wall .... 5

1.I Dimensions ....................................................... 6

SECTION 2 Venting and Combustion Air

2.A Combustion Air ................................................. 8

2.A.1 Combustion Air From Room ............................. 8

2.A.2 Intake Combustion Air ...................................... 8

2.B Venting .............................................................. 8

2.B.1 Vent Categories ................................................ 8

2.B.2 Category I Vent ................................................. 9

2.B.3 Common Venting Systems ............................... 9

2.B.4 Category III Vent ............................................... 9

2.C Locating Vent & Combustion Air Terminals ..... 10

2.C.1 Side Wall Vent Terminal .................................. 10

2.C.2 Side Wall Combustion Air Terminal ................. 10

2.C.3 Vertical Vent Terminal ..................................... 10

2.C.4 Vertical Combustion Air Terminal .................... 12

2.D Common Vent Test — Boilers ......................... 12

2.E Vent Terminals for Outdoor Units .................... 13

SECTION 3 Gas Supply and Piping

3.A Gas Supply and Piping ................................... 14

SECTION 4 Water Connections

4.A Boilers. .......................................................... 15

4.A.1 Heating System Piping:

Hot Supply Connections — Boiler .................. 15

4.A.2 Cold Water Make-Up — Boiler ....................... 15

4.A.3 Water Flow Requirements — Boiler ............... 15

4.A.4 Freeze Protection — Boiler ............................ 16

4.B Water Heater .................................................. 16

4.B.1 Water System Piping — Water Heater ........... 16

4.B.2 Hot Water Supply Piping — Water Heater ...... 16

4.B.3 Water Flow Requirements — Water Heater ... 16

4.B.4 Combined Water Heating (potable)

and Space Heating — Water Heater ............. 17

4.B.5 Freeze Protection – Water Heater .................. 17

SECTION 5 Electrical Connections

5.A Main Power ..................................................... 23

5.A.1 Changing Single Circuit to Two Circuits ......... 23

6.H.1 Field Wiring ..................................................... 28

6.I External Staging Control Wiring ..................... 28

SECTION 6 Operating Instructions

6.A Sequence of Operation ................................... 28

6.B Filling the System ........................................... 29

6.C Operating Temperature Control ...................... 30

6.D External Boiler Operations .............................. 30

6.E Limit Controls .................................................. 30

6.F Operating the Burner and Set Up ................... 30

6.F.1 Set Up for 0 to 2500 Feet Altitude .................. 30

6.F.2 High Altitude Adjustment and Set Up .............. 31

6.G Shutting Down the Unit ................................... 31

6.H To Restart the Unit .......................................... 31

MIGHTY THERM2 Commercial Boilers and Volume Water Heaters

SECTION 7 Maintenance

7.A System Maintenance ...................................... 32

7.B Maintenance and Component Description ..... 32

7.B.1 Burners ........................................................... 32

7.B.2 Filter ................................................................ 32

7.B.3 Gas Valves ..................................................... 32

7.B.4 Manual Reset High Limit Control .................... 32

7.B.5 Temperature Control ....................................... 33

7.B.6 Ignition Controls .............................................. 33

7.B.7 Ignitors/Sensor ............................................... 33

7.B.8 Transformer .................................................... 33

7.B.9 Blowers ........................................................... 33

7.B.10 Flow Switch ................................................... 33

7.B.11 Heat Exchanger Coil ..................................... 33

SECTION 8 Trouble Shooting

8.A Resolving Lockouts ........................................ 34

8.B Delayed Ignition — Possible Causes ............. 34

8.C Short Cycling — Boiler ................................... 35

8.D Short Cycling — Water Heater ....................... 35

8.E High Gas Consumption .................................. 35

SECTION 9 Replacement Parts

9.A General Information ........................................ 35

9.B Parts List ........................................................ 35

MIGHTY THERM2 Commercial Boilers and Volume Water Heaters

Page 1

USING THIS MANUAL – Because these Boilers

and Water Heaters are identical appliances, with the

exception of materials of manufacture, labels and

ultimate use and application, this manual provides

information for the proper installation, operation and

maintenance of both products. Where dierences

exist between their application and their operation,

the sections pertinent to only one or the other will be

so identied.

In the Commonwealth of Massachusetts, this unit

must be installed by a licensed plumber or gas tter.

This manual provides information necessary for

the installation, operation, and maintenance of the

Laars Heating Systems Mighty Therm2 commerical

hydronic boilers and volume water heaters (including

the Low Temp units). Read this manual carefully before

installation.

All application and installation procedures should

be reviewed completely before proceeding with

the installation. Consult the factory, or local factory

representative, with any issues or questions regarding

this equipment. Experience has shown that most

operating issues are caused by improper installation.

The Mighty Therm2 is protected against over

pressurization. A pressure relief valve is tted to all units.

It is installed on the outlet header, at the water outlet of

the unit

Laars Heating Systems Mighty Therm2s are

covered by a limited warranty. Owners should submit

online warranty registration at www.Laars.com.

All warranty claims must be made to an authorized

Laars Heating Systems representative, directly to

Customer Service, or online at www.Laars.com.

Claims must include the serial number and model

number (this information can be found on the rating

plate), installation date, and name of the installer.

Shipping costs are not included in the warranty

coverage.

Some accessory items are shipped in separate

packages. Verify receipt of all packages listed on

the packing slip. Inspect everything for damage

immediately upon delivery, and advise the carrier of

any shortages or damage. Any such claims should be

led with the carrier. The carrier, not the shipper, is

responsible for shortages and damage to the shipment

whether visible or concealed.

1.A Introduction

1.B Warranty

NOTE: Throughout the content of this

manual, the Mighty Therm2 will be referred to

as a ‘unit’. unit = MightyTherm2

SECTION 1 General Information

GAS

VENTINLET

HYDRONIC SUPPLY

AND RETURN

The Pump and the Hydronic Supply/Return are reversible.

GAS

PUMP

LAARS Heating Systems

Page 2

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

M T 2 A C K 1

SERIES

M T 2

SIZE

0 5 0 0

0 7 5 0

1 0 0 0

1 2 5 0

1 5 0 0

1 7 5 0

2 0 0 0

REVISION

1 - FIRST

REV

OPTIONS

CODE

X - STD

J - CSD-1,

GAP,

USAGE

H - HYDRONIC

V - VOLUME WATER

FUEL

N - NATURAL

P - PROPANE

PUMP

OPTIONS

X - NO PUMP

H - PUMP MOUNTED

TACO, HARD

WATER (MT2V)

N - PUMP MOUNTED,

TACO, NORMAL

WATER (MT2V, MT2H)

S - PUMP MTD, TACO

SOFT WATER PUMP

(MT2V)

C - PUMP MOUNTED

B&G, HARD

WATER (MT2V)

B - PUMP MOUNTED,

B&G, NORMAL

WATER (MT2V, MT2H)

D - PUMP MTD, B&G

SOFT WATER PUMP

(MT2V)

ALTITUDE

A - 0' – 10,000'

LOCATION

C - INDOOR/

OUTDOOR

FIRING

MODE

K - 2-Stage

HEAT EXCHANGER

B - GLASS-LINED CAST IRON/

COPP/BRZ TRIM (std.MT2V)

C - GLASS-LINED CASTIRON/

COPP. (std.MT2H, n/a MT2V)

N - GLASS-LINED CAST IRON/

CU-NICKEL (n/a MT2V)

P - GLASS-LINED CAST IRON /

CU-NICKEL, BRZ TRIM

HLW STAMP (MT2V only)

2 - GLASS-LINED CAST IRON/

COPPER / BRZ TRIM

5 - GLASS-LINED CAST IRON/

CU-NICKEL / BRZ TRIM

Consult the rating plate on the unit.

The following information describes the

model number structure.

1-3 Model Series Designation

M T 2 = Mighty Therm2

4 Usage

H = Hydronic

V = Volume Water

5-8 Size

0 5 0 0 = 500,000 BTU/h input

0 7 5 0 = 750,000 BTU/h input

1 0 0 0 = 999,000 BTU/h input

1 2 5 0 = 1,250,000 BTU/h input

1 5 0 0 = 1,500,000 BTU/h input

1 7 5 0 = 1,750,000 BTU/h input

2 0 0 0 = 1,999,000 BTU/h input

9 Fuel

N = Natural Gas

P = Propane

10 Altitude

A = 0–10,000 feet

11 Location

C = Indoor and Outdoor

12 Firing Mode

K = Two-stage

13 Revision

1 = First version of design

14 Heat Exchanger

B = Glass-lined cast iron / copper / bronze trim

(std. on water heaters)

C = Glass-lined cast iron / copper

(std. on boilers, n/a on water heaters)

N = Glass-lined cast iron / cupro-nickel

(n/a on water heaters)

P = Glass-lined cast iron / cu-nickel / bronze trim

15 Option Code

X = Standard unit

J = CSD-1, FM, IRI, IL

16 Pump Options

X = No Pump

H = Pump mounted MT2V, TACO, hard water pump

N = Pump mounted (any), TACO, normal water pump

S = Pump mounted MT2V, TACO, soft water pump

C = Pump mounted MT2V, B&G, hard water pump

B = Pump mounted (any), B&G, normal water pump

D = Pump mounted MT2V, B&G, soft water pump

1.C Model Identication

(Model Nomenclature)

MIGHTY THERM2 Commercial Boilers and Volume Water Heaters

Page 3

1.D Safety Notes

WARNING

Carbon Monoxide Hazard

Improper adjustment of the burners may lead to poor

combustion quality, increasing the amount of carbon

monoxide produced. Excessive carbon monoxide

levels may lead to personal injury or death.

WARNING

This unit must be installed in accordance with the

procedures detailed in this manual, or the manufacturers

warranty will be voided. The installation must conform

to the requirements of the local jurisdiction having

authority, and, in the United States, to the latest edition

of the National Fuel Gas Code, ANSI Z223.1/NFPA54.

In Canada, the installation must conform to the latest

edition of CSA B149.1 Natural Gas and Propane Gas

Installation Code, and/or local codes. Where required

by the authority having jurisdiction, the installation of

these units must conform to the Standard for Controls

and Safety Devices for Automatically Fired Boilers,

ANSI/ASME CSD-1. Any modiﬁ cations to the boiler, its

gas controls, or wiring may void the warranty. If ﬁ eld

conditions require modiﬁ cations, consult the factory

representative before initiating such modiﬁ cations.

WARNING

• Water temperature over 125°F (52°C) can cause

severe burns instantly or death from scalds.

• Children, disabled and

elderly are at highest

risk of being scalded.

• See instruction manual

before setting temperature

at the unit.

• Feel water before bathing

or showering.

• If this unit is used

to produce water that could scald if too hot, such

as domestic hot water use, adjust the outlet control

(limit) or use temperature limiting valves to obtain a

maximum water temperature of 125°F (52°C).

WARNING

The inlet gas pressure to the unit must not

exceed 13” W.C. (3.2kPa).

WARNING

Fire or Explosion Hazard

Improper conﬁ guration can cause fuel buildup and

explosion. Improper user operation may result in

property loss, severe physical injury, or death.

Any changes to safety-related conﬁ guration

parameters must only be done by experienced and/or

licensed burner/boiler operators and mechanics.

If any odor of gas is detected, or if the gas burner does

not appear to be functioning in a normal manner, close

the main gas shutoﬀ valve. Do not shut oﬀ the power

switch. Contact your heating contractor, gas company,

or factory representative.

NOTE: This unit is protected against hydronic

over-pressurization. A pressure relief valve is included

with each unit.

WARNING

Indicates an imminently hazardous situation which, if not

avoided, can or will result in death or serious injury and can

or will result in catastrophic property damage.

CAUTION

Indicates a potentially hazardous situation which, if not avoided,

may result in moderate injury and/or property damage.

NOTE:

Indicates instructions that are important to that topic but not

related to personal injury or property damage.

Safety Notes are used thoughout this manual to bring attention to the presence of hazards with various

risk levels and to oﬀ er important information concering the life of this product. There are 3 basic types.

WARNING

CANCER AND REPRODUCTIVE HARM.

WWW.P65WARNINGS.CA.GOV.

AS REQUIRED BY THE STATE OF

CALIFORNIA PROPOSITION 65.

LAARS Heating Systems

Page 4

WARNING

Electrical Shock Hazard

Electrical shock can cause severe injury, death or

property damage. Disconnect the power supply before

beginning installation or changing the wiring to prevent

electrical shock or damage to the equipment. It may be

necessary to turn oﬀ more than one power supply

to disconnect.

All electrical wiring is to be done in accordance with

local codes, or in the absence of local codes, with: 1)

The National Electrical Code ANSI/NFPA No. 70 - latest

Edition, or 2) CSA STD. C22.1 “Canadian Electrical Code

- Part 1.” This appliance must be electrically grounded in

accordance with these codes.

WARNING

The Repair Parts list designates parts that contain

refractory ceramic ﬁ bers (RCF). RCF has been classiﬁ ed

as a possible human carcinogen. When exposed to

temperatures above 180ºF, such as during direct ﬂ ame

contact, RCF changes into crystalline silica, a known

carcinogen. When disturbed as a result of servicing or

repair, these substances become airborne and, if inhaled,

may be hazardous to your health.

Do not remove or replace RCF parts or attempt any

service or repair work involving RCF without wearing

the following protective gear:

1. A National Institute for Occupational Safety and

Health (NIOSH) approved respirator.

2. Long sleeved, loose ﬁ tting clothing.

3. Gloves.

4. Eye Protection.

NOTE: All installations must be made in accordance with

1) American National Standard Z223.1/NFPA54-Latest

Edition “National Fuel Gas Code” or

2) CSA B149.1 “Natural Gas and Propane Installation

Code” or in Canada reference the B149.1 latest

edition and with the requirement of the local utility or

other authorities having jurisdiction. Such applicable

requirements take precedence over the general

instructions contained herein. All electrical wiring is to

be done in accordance with the local codes, or in the

absence of local codes, with: 1) The National Electrical

Code ANSI/NFPA No. 70-latest Edition, or

2) CSA STD. C22.1 “Canadian Electrical Code - Part

1”. This appliance must be electrically grounded in

accordance with these codes.

MIGHTY THERM2 Commercial Boilers and Volume Water Heaters

Page 5

REQUIRED RECOMMENDED

CLEARANCE FROM SERVICE ACCESS

SURFACE COMBUSTIBLE MATERIAL CLEARANCE

inches cm inches cm

Left Side 1 2.5 24 61

Right Side 1 2.5 24 61

Top 1 2.5 12 30

Back 1 2.5 **12** 30**

Front 1 2.5 36 91

Vertical

(Category 1) 6* 15.2*

Vent

Horizontal per UL1738 venting

(Category 3) system supplier’s

Vent instructions

*1" (2.5cm) when b-vent is used.

**When vent and/or combustion air connects to the back,

recommended clearance is 36" (91cm).

1.E Locating the unit

This unit should be located to provide clearances

on all sides for maintenance and inspection. It should not

be located in an area where leakage of any connections

will result in damage to the area adjacent to the unit or to

lower oors of the structure.

When such a location is not available, it is

recommended that a suitable drain pan, adequately

drained, be installed under the unit.

This unit is design certied by CSA-International

for installation on combustible ooring; in basements;

in closets, utility rooms or alcoves. These units must

never be installed on carpeting. The location for

the unit should be chosen with regard to the vent

pipe lengths and external plumbing. The unit shall be

installed such that the gas ignition system components

are protected from water (dripping, spraying, rain, etc.)

during operation and service (circulator replacement,

control replacement, etc.). When vented vertically, this

unit must be located as close as practical to a chimney

or outside wall. If the vent terminal and/or combustion air

terminal terminate through a wall, and there is potential

for snow accumulation in the local area, both terminals

should be installed at an appropriate level above grade.

The dimensions and requirements that are shown

in Table 1 should be met when choosing the locations for

the unit.

1.F Locating Pump-Mounted Water Heater

with Respect to Storage Tank(s)

For best results, a pump-mounted water heating

unit should be located within 15 feet (4.6m) of the

storage tank(s). The pump is sized for 30 feet (9.1m) of

piping.

If the unit must be installed with longer piping

runs, then larger diameter pipe or tubing shall be used.

Consult the factory for assistance.

1.G Locating Pump-Mounted Boiler with

Respect to Return/Supply Header

For the best results, a pump-mounted boiler should

be located within 15 feet (4.6m) of the supply and return

headers. The pump is sized for 30 feet (9.1m) of piping.

If the unit must be installed with longer piping runs,

then larger diameter tubing shall be used. Consult the

factory for assistance.

1.H Locating the Unit for Correct

Horizontal Vent/Ducted Air Distance

from Outside Wall

The forced draft combustion air blower/blowers in

the unit has/have sucient power to pull air and vent

properly when the following guidelines for horizontal air

and vent are followed (see Table 2).

NOTE: The vent collar size is larger than the size of

the vent pipe that can be used. Vent collar size and

horizontal pipe diameters can be found in Table 2. The

larger vent collar size is to accommodate Category I

(vertical) vent systems.

NOTE: When located on the same wall, the

combustion air intake terminal must be installed

a minimum of 12" (30cm) below the exhaust vent

terminal and separated by a minimum of 36 inches

(91cm) horizontally.

The air intake terminal must be installed high

enough to avoid blockage from snow, leaves and other

debris.

Table 1. Clearances

LAARS Heating Systems

Page 6

1.I Dimensions

See Figures 1 and 2.

Figure 1. Dimensional Data (standard units).

Air Vent Shipping Weight

Unit Conn. Conn.

Size A B C D E W V lbs kg

500 33¾ 85 16¾ 43 6½ 17 10 25 8 20 6 15 8 20 425 193

750 45¾ 116 22¾ 53 6½ 17 10 25 9½ 24 8 20 10 25 505 229

1000 57¾ 147 28¾ 73 6½ 17 10 25 9½ 24 8 20 10 25 615 279

1250 68¼ 173 34 87 10¼

26 10 25 9 23 12 30 12 30 675 306

1500 78¾ 200 39½ 100 10¼

26 10 25 9 23 12 30 12 30 760 345

1750 89¼ 227 44¾ 113 10¼

26 10 25 9 23 12 30 14 36 825 375

2000 99¾ 253 49¾ 127 10¼

26 10 25 9 23 12 30 14 36 955 434

NOTES: 1. Add 55 lbs (25kg) for pump-mounted units.

Dimensions in inches cm.

GAS

MIGHTY THERM2 Commercial Boilers and Volume Water Heaters

Page 7

GAS

Air Vent

Conn. Conn.

Size A B C D E F W V

500 33¾ 86 16¾ 43 6½ 17 10 25 8 20 46¼ 117 6 15 8 20

750 45¾ 116 22¾ 58 6½ 17 10 25 9½ 24 58¼ 148 8 20 10 25

1000 57¾ 147 28¾ 73 6½ 17 10 25 9½ 24 70¼ 178 8 20 10 25

1250 68¼ 173 34¼ 87 10¼

26 10 25 9 23 80¾ 205 12 30 12 30

1500 78¾ 200 39½ 100 10¼

26 10 25 9 23 91¼ 232 12 30 12 30

1750 89¼ 227 44¾ 113 10¼

26 10 25 9 23 101¾ 258 12 30 14 36

2000 99¾ 253 49¾ 127 10¼ 26 10 25 9 23 112¼ 285 12 30 14 36

Figure 2. Dimensional Data (pump-mounted models).

HORIZONTAL INTAKE AIR

VENT COLLAR VENT PIPE PIPE MAX. PIPE MAX. NO. SIDE WALL SIDE WALL

SIZE SIZE DIAMETER DIAMETER LENGTH OF ELBOWS VENT COMBUSTION

TERMINAL AIR TERMINAL

in. cm in. cm in. cm ft. m PART NUMBER PART NUMBER

500 8 20 6 15 6 15 50 15 3 CA001401 CA20260701

750 10 25 8 20 8 20 50 15 3 CA001402 CA20260703

1000 10 25 8 20 8 20 50 15 3 CA001402 CA20260703

1250 12 30 10 25 12 30 50 15 3 CA001405 CA20260706

1500 12 30 10 25 12 30 50 15 3 CA001405 CA20260706

1750 14 36 12 30 12 30 50 15 3 CA001404 CA20260706

2000 14 36 12 30 12 30 50 15 3 CA001404 CA20260706

Table 2. Horizontal Vent / Combustion Air Parameters.

LAARS Heating Systems

Page 8

UNIT

EACH OPENING*

SIZE

SQUARE INCHES SQUARE CM

500 125 807

750 188 1213

1000 250 1613

1250 313 2020

1500 375 2420

1750 438 2826

2000 500 3226

*Net Free Area in Square Inches / Square cm

Area indicated is for one of two openings; one at oor level and one

at the ceiling, so the total net free area could be double the gures

indicated.

This chart is for use when communicating directly with the

outdoors. For special conditions and alternate methods, refer to the

latest edition of ANSI Z223.1.

Note: Check with louver manufacturers for net free area of

louvers. Correct for screen resistance to the net free area if a

screen is installed. Check all local codes applicable to combustion air.

Table 3. Combustion Air Openings.

SECTION 2 Venting and

Combustion Air

2.A Combustion Air

These boilers and water heaters must have

provisions for combustion and ventilation air in

accordance with section 5.3, Air for Combustion and

Ventilation, of the National Fuel Gas Code, ANSI Z223.1,

or Sections 7.2, 7.3 or 7.4 of CSA B149.1, Installation

Codes, or applicable provisions of the local building

codes.

This unit may receive combustion air from the

space in which it is installed, or it can be ducted directly

to the unit from the outside. Ventilation air must be

provided in either case.

2.A.1 Combustion Air From Room

In the United States, the most common

requirements specify that the space shall communicate

with the outdoors in accordance with method 1 or 2,

which follow. Where ducts are used, they shall be of

the same cross-sectional area as the free area of the

openings to which they connect.

Method 1: Two permanent openings, one

commencing within 12 inches (30 cm) of the top and

one commencing within 12 inches (30 cm) of the bottom,

of the enclosure shall be provided. The openings shall

communicate directly, or by ducts, with the outdoors

or spaces that freely communicate with the outdoors.

When directly communicating with the outdoors, or

when communicating to the outdoors through vertical

ducts, each opening shall have a minimum free area of

1 square inch per 4000 BTU/hr (5.5 square cm/kW) of

total input rating of all equipment in the enclosure. When

communicating to the outdoors through horizontal ducts,

each opening shall have a minimum free area of not less

than 1 square inch per 2000 BTU/hr (11 square cm/kW)

of total input rating of all equipment in the enclosure.

Table 3 shows data for this sizing method, and for each

model.

Method 2: One permanent opening, commencing

within 12 inches (30 cm) of the top of the enclosure, shall

be permitted. The opening shall directly communicate

with the outdoors or shall communicate through a

vertical or horizontal duct to the outdoors or spaces that

directly communicate with the outdoors and shall have a

minimum free area of 1 square inch per 3000 BTU/hr (7

square cm/kW) of the total input rating of all equipment

located in the enclosure. This opening must not be less

than the sum of the areas of all vent connectors in the

conned space.

Other methods of introducing combustion and

ventilation air are acceptable, providing they conform to

the requirements in the applicable codes listed above.

In Canada, consult local building and safety codes

or, in absence of such requirements, follow CSA B149.1.

2.A.2 Intake Combustion Air

The combustion air can be taken through the wall,

or through the roof. When taken from the wall, it must be

taken from out-of-doors by means of the Manufacturers

horizontal wall terminal (see Table 2). When taken

from the roof, a eld-supplied rain cap or an elbow

arrangement must be used to prevent entry of rain water

(see Figure 3).

Use single-wall galvanized pipe, per Table 4, for the

combustion air intake (see Table 2 for appropriate size).

Route the intake to the heater as directly as possible.

Seal all joints with tape. Provide adequate hangers. The

unit must not support the weight of the combustion air

intake pipe. Maximum linear pipe length allowed is 50

feet (15.2m). Three elbows have been calculated into the

50-foot (15.2m) linear run. Subtract 10 allowable linear

feet (3.0m) for every additional elbow used (see Table

2). When fewer than 3 elbows are used, the maximum

linear pipe length allowed is still 50 feet (15.2m).

The connection for the intake air pipe is on the lter

box. This unit has venting and combustion air ducting

attached to the top.

In addition to air needed for combustion, air shall

also be supplied for ventilation, including all air required

for comfort and proper working conditions for personnel.

This unit loses less than 1 percent of its input rating to

the room, but other heat sources may be present.

2.B Venting

2.B.1 Vent Categories

Depending upon desired venting for this unit, it may

be considered a Category I or a Category III appliance.

In general, a vertical vent system will be a Category

I system. However, in rare instances, a vertical vent

system may be considered Category III. In the U.S., the

National Fuel Gas Code (ANSI Z223.1-Latest Edition),

MIGHTY THERM2 Commercial Boilers and Volume Water Heaters

Page 9

Figure 3. Combustion Air and Vent Through Roof.

TERM DESCRIPTION

Pipe Single-wall galvanized steel pipe, 24 gauge

minimum (either insulated or non-insulated)

Joint Permanent duct tape or aluminum tape

Sealing

Table 4. Required Combustion Air Piping Material.

or in Canada the CSA B149.1 (latest edition), denes a

Category I vent system, and includes rules and tables to

size these vent systems. If this units vertical vent system

does not satisfy the criteria for Category I venting, it

must be vented as a Category III system.

All vent systems which discharge horizontally

(without the use of a power venter) are considered

Category III vent systems.

2.B.2 Category I Vent

When vented as a category I appliance, the vent

system must conform to the National Fuel Gas Code

(ANSI Z223.1-Latest Edition) in the U.S., or in Canada,

to CSA B149.1 (latest edition). The vent system must

be sized and installed for a Category I Fan-Assisted

Appliance.

If chimney height is greater than 25 feet, or if

multiple units are vented into the same vertical vent, a

barometric damper must be installed on each unit, such

that the ue draft does not exceed (negative) 0.1" w.c.

If using a power venter for any type of Category I

venting, the draft should be set between (negative) 0.01

and 0.10" w.c.

2.B.3 Common Venting Systems

These units are Category I fan-assisted when

vented vertically and adhering to all applicable codes.

When common venting a fan-assisted unit with

other other appliances through one shared vertical duct

called a “common vent”, special care must be taken by

the installer to ensure safe operation. In the event that

the common vent is blocked, it is possible, especially

for fan-assisted devices, to vent backwards through

non-operating appliances sharing the vent, allowing

combustion products to inltrate occupied spaces. If the

appliances are allowed to operate in this condition,

serious injury or death may occur.

WARNING

Operation of appliances with a blocked common

vent may lead to serious injury or death. If safe

operation of all appliances connected to a common

vent cannot be assured, including prevention of

spillage of ue gasses into living spaces, common

venting should not be applied, and appliances

should each be vented separately.

Proper vent sizing, construction and safety

requirements from the National Fuel Gas Code, ANSI

Z223.1 or in Canada, from CSA B149.1 as well as all

applicable local codes must be followed.

As an additional precaution, it is recommended

that a Carbon Monoxide (CO) alarm be installed in all

enclosed spaces containing combustion appliances.

MightyTherm2 units are not allowed to be vented

into a common horizontal Cat III vent system (horizontal

discharge or other conguration for Cat III), unless

a properly sized vent fan is used, and the common

vent system is properly designed by the vent fan

manufacturer or a qualied engineer.

Refer to the installation and operating instructions

on all appliances to be common vented for instructions,

warnings, restrictions and safety requirements. If safe

operation of all appliances connected to a common vent

cannot be assured, including prevention of spillage of

ue gasses into living spaces, common venting should

not be applied, and appliances should each be vented

separately.

2.B.4 Category III Vent

When this unit is vented with horizontal discharge,

it must be installed per this installation manual and the

venting system manufacturer’s installation instructions.

The vent system must be sealed stainless steel (see

Table 5).

Route the vent pipe to the heater as directly as

possible. Seal all joints and provide adequate hangers

as required in the venting system manufacturer’s Instal-

lation Instructions. Horizontal portions of the venting

system must be supported to prevent sagging and may

not have any low sections that could trap condensate.

The unit must not support the weight of the vent pipe.

LAARS Heating Systems

Page 10

TERM DESCRIPTION

Pipe Must comply with UL Standard 1738

such as Type 29-4C Stainless Steel

(either insulated or non-insulated).

Joint Follow vent manufacturer’s instructions

Sealing

Table 5. Required Horizontal Venting Material.

Horizontal runs must slope downwards not less than ¼

inch per foot (2 cm/m) from the unit to the vent terminal.

Reference Table 2 for the size of the Category III vent

system. Up to three elbows can be used with 50 linear

feet (15.2m) of pipe. Subtract 10 allowable linear feet

(3.0m) for every additional elbow used.

WARNING

The outdoor vent terminal gets hot. This unit must

be installed in such a way as to reduce the risk of

burns from contact with the vent terminal.

2.C Locating Vent & Combustion Air

Terminals

2.C.1 Side Wall Vent Terminal

The appropriate manufacturers side wall vent

hood must be used, and is listed in the installation

and operation manual. The terminal provides a means

of installing the vent piping through the building wall,

and must be located in accordance with ANSI Z223.1/

NFPA 54 and applicable local codes. In Canada, the

installation must be in accordance with CSA B149.1 or .2

and local applicable codes. Consider the following when

installing the terminal:

1. Figure 4 shows the requirements for mechanical vent

terminal clearances for the U.S. and Canada.

2. Vent terminals for condensing appliances or

appliances with condensing vents are not permitted

to terminate above a public walkway, or over an area

where condensate or vapor could create a nuisance

or hazard.

3. Locate the vent terminal so that vent gases cannot be

drawn into air conditioning system inlets.

4. Locate the vent terminal so that vent gases cannot

enter the building through doors, windows, gravity

inlets or other openings. When possible, locations

under windows or near doors should be avoided.

5. Locate the vent terminal so that it cannot be blocked

by snow. The National Fuel gas code requires that

it be at a minimum of 12" above grade. In a location

that has the possibility of snow accumulation, it

is critical the installer places the vent at least 12"

higher than the maximum potential snow line. Seek

local municipalities and their codes for appropriate

installation techniques.

6. Locate the terminal so the vent exhaust does not

settle on building surfaces or other nearby objects.

Vent products may damage such surfaces or objects.

7. If the boiler or water heater uses ducted

combustion air from an intake terminal located on

the same wall, locate the vent terminal at least 3

feet (0.9m) horizontally from the combustion air

terminal, and locate the vent terminal at least 1 foot

(0.3m) above the combustion air terminal.

2.C.2 Side Wall Combustion Air Terminal

The manufacturers side wall combustion air

terminal (see Table 2) must be used when the unit

takes its combustion air through a duct from a side wall.

Consider the following when installing the terminal:

1. Do not locate the air inlet terminal near a source

of corrosive chemical fumes (e.g., cleaning uid,

chlorinated compounds, etc.)

2. Locate the terminal so that it will not be subject to

damage by accident or vandalism.

3. Locate the combustion air terminal so that it

cannot be blocked by snow. The National Fuel

gas code requires that it be at a minimum of 12"

above grade. Depending on local conditions, the

installer should ensure that it remains at least 12"

above the maximum potential snow line. Seek

local municipalities and their codes for appropriate

installation techniques.

WARNING

It is critical that the combustion air intake and the vent

terminals remain at least 12" above the maximum

potential snow line. If either the vent terminal or the

air terminal is blocked by snow, there may be potential

for the unit to produce excess carbon monoxide and

or recirculate ue gasses into the building/dwelling.

Personal injury or DEATH may occur. Natural snowfall,

drifting, and banking should all be taken into account

when locating the terminals in a potential snow

environment.

4. If this unit is side-wall vented to the same wall,

locate the vent terminal at least 3 feet (0.9m)

horizontally from the combustion air terminal, and

locate the vent terminal at least 1 foot (0.3m) above

the combustion air terminal (see Figure 4).

2.C.3 Vertical Vent Terminal

When the unit is vented through the roof, the vent

must extend at least 3 feet (0.9m) above the point at

which it penetrates the roof. It must extend at least 2

feet (0.6m) higher than any portion of a building within a

horizontal distance of 10 feet (3.0m), and high enough

above the roof line to prevent blockage from snow. When

the combustion air is taken from the roof, the combustion

air must terminate at least 12" (30cm) below the vent

terminal (see Figure 3). Seek local municipalities and

their codes for appropriate installation techniques.

From Massachusetts Rules and Regulations 248 CMR 5.08:

(a) For all side wall horizontally vented gas fueled equip-

ment installed in every dwelling, building or structure

MIGHTY THERM2 Commercial Boilers and Volume Water Heaters

Page 11

U.S. Installations (see note 1) Canadian Installations (see note 2)

A= Clearance above grade, veranda, porch, 12 inches (30 cm) 12 inches (30 cm)

deck, or balcony

B= Clearance to window or door that may be 4 feet (1.2 m) below or to side of opening; 36 inches (91 cm)

opened 1 foot (30 cm) above opening

C= Clearance to permanently closed window See note 4 See note 5

D= Vertical clearance to ventilated sot located

above the terminal within a horizontal See note 4 See note 5

distance of 2 feet (61cm) from the center

line of the terminal

E= Clearance to unventilated sot See note 4 See note 5

F= Clearance to outside corner See note 4 See note 5

G= Clearance to inside corner See note 4 See note 5

H= Clearance to each side of center line 3 feet (91 cm) within a height 15 feet above

extended above meter/regulator assembly See note 4 the meter/regulator assembly

I= Clearance to service regulator vent outlet See note 4 3 feet (91 cm)

J= Clearance to nonmechanical air supply inlet

to building or the combustion air inlet to 4 feet (1.2 m) below or to side of opening; 36 inches (91 cm)

any other appliance 1 foot (30 cm) above opening

K= Clearance to a mechanical air supply inlet 3 feet (91 cm) above if within 10 feet (3 m) 6 feet (1.83 m)

horizontally

Vent termination not allowed in this location

Vent termination not allowed in this location for category IV appliances. A vent shall not

L= Clearance above paved sidewalk or paved for category IV appliances. For Category III terminate directly above a sidewalk or paved

driveway located on public property appliances, vent must terminate at least 7 driveway that is located between two single

feet (2.13m) above the sidewalk or driveway. family dwellings and serves both dwellings.

For Category III appliances that do not violate

the previous condition, vent must terminate

at least 7 feet (2.13m) above the sidewalk or

driveway.

M= Clearance under veranda, porch, deck, See note 4 12 inches (30 cm) (see note 3)

or balcony

Notes:

1. In accordance with the current ANSI Z223.1 / NFPA 54 National Fuel Gas Code.

2. In accordance with the current CSA-B149.1 Installation Codes.

3. Permitted only if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath the oor.

4. For clearances not specied in ANSI Z223.1 / NFPA 54, clearance is in accordance with local installation codes and the requirements of

the gas supplier.

5. For clearances not specied in CSA-B149.1, clearance is in accordance with local installation codes and the requirements of the gas supplier.

Figure 4. Combustion Air and Vent Through Side Wall.

LAARS Heating Systems

Page 12

used in whole or inpart for residential purposes, includ-

ing those owned or operated by the Commonwealth and

where the side wall exhaust vent termination is less than

seven (7) feet above nished grade in the area of the

venting, including but not limited to decks and porches,

the following requirements shall be satised:

1. INSTALLATION OF CARBON MONOXIDE DETECTORS.

At the time of installation of the side wall horizontal vented

gas fueled equipment, the installing plumber or gastter shall

observe that a hard-wired carbon monoxide detector with

an alarm and battery back-up is installed on the oor level

where the gas equipment is to be installed. In addition, the

installing plumber or gastter shall observe that a battery op-

erated or hard-wired carbon monoxide detector with an alarm

is installed on each additional level of the dwelling, building

or structure served by the side wall horizontal vented gas

fueled equipment. It shall be the responsibility of the property

owner to secure the services of qualied licensed profes-

sionals for the installation of hard-wired carbon monoxide

detectors.

a. In the event that the side wall horizontally vented gas

fueled equipment is installed in a crawl space or an attic, the

hard-wired carbon monoxide detector with alarm and battery

back-up may be installed on the next adjacent oor level.

b. In the event that the requirements of this subdivision

cannot be met at the time of completion of installation, the

owner shall have a period of thirty (30) days to comply with

the above requirements; provided, however, that during said

thirty (30) day period, a battery operated carbon monoxide

detector with an alarm shall be installed.

2. APPROVED CARBON MONOXIDE DETECTORS. Each

carbon monoxide detector as required in accordance with the

above provisions shall comply with NFPA 720 and be ANSI/

UL 2034 listed and IAS certied.

3. SIGNAGE. A metal or plastic identication plate shall be

permanently mounted to the exterior of the building at a

minimum height of eight (8) feet above grade directly in line

with the exhaust vent terminal for the horizontally vented

gas fueled heating appliance or equipment. The sign shall

read, in print size no less than one-half (½) inch in size,

"GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL

OBSTRUCTIONS".

4. INSPECTION. The state or local gas inspector of the side

wall horizontally vented gas fueled equipment shall not ap-

prove the installation unless, upon inspection, the inspector

observes carbon monoxide detectors and signage installed

in accordance with the provisions of 248 CMR 5.08(2)(a) 1

through 4.

(b) EXEMPTIONS: The following equipment is exempt from

248 CMR 5.08(2)(a) 1 through 4:

1. The equipment listed in Chapter 10 entitled "Equipment Not

Required To Be Vented" in the most current edition of NFPA

54 as adopted by the Board; and

2. Product Approved side wall horizontal vented gas fueled

equipment installed in a room or structure separate from the

dwelling, building or structure used in whole or in part for

residential purposes.

VENTING SYSTEM PROVIDED. When the manufacturer of

Product Approved side wall horizontally vented gas equip-

ment provides a venting system design or venting system

components with the equipment, the instructions provided

by the manufacturer for installation of the equipment and the

venting system shall include:

1. Detailed instructions for the installation of the venting system

design or the venting system components; and

2. A complete parts list for the venting system design or venting

system.

(d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT

VENTING SYSTEMNOT PROVIDED. When the manufac-

turer of a Product Approved side wall horizontally vented gas

fueled equipment does not provide the parts for venting the

fuel gases, but identies "special venting systems", the fol-

lowing requirements shall be satised by the manufacturer:

1. The identication of each "special venting system" shall

include either the listing of the website, phone number or

manufacturer's address where the venting system installation

instructions can be obtained; and

2. The "special venting systems" shall be Product Approved

by the Board, and the instructions provided with that system

shall include a parts list and detailed installation instructions.

(e) A copy of all installation instructions for the Product

Approved side wall horizontally vented gas fueled equip-

ment, and all the venting instructions, parts lists, and/or

design instructions for the venting system shall remain

with the appliance or equipment at the completion of the

installation.

Manufacturers' websites where venting system installation

instructions may be obtained is located on the manufacturers

website (see back cover).

2.C.4 Vertical Combustion Air Terminal

When combustion air is taken from the roof, a

eld-supplied rain cap or an elbow arrangement must be

used to prevent entry of rain water (see Figure 3). The

opening on the end of the terminal must be at least 12"

(30cm) above the point at which it penetrates the roof,

and high enough above the roof line to prevent blockage

from snow. When the vent terminates on the roof, the

combustion air must terminate at least 12" (30cm) below

the vent terminal.

2.D Common Vent Test — Boilers

When an existing boiler is removed from a common

venting system, the common venting system is likely

to be too large for proper venting of the appliances

remaining connected to it.

At the time of removal of an existing boiler, the

following steps shall be followed with each appliance

remaining connected to the common venting system

placed in operation, while the other appliances remain-

ing connected to the common venting system are not in

operation.

1. Seal any unused openings in the common venting

system.

2. Visually inspect the venting system for proper

size and horizontal pitch and determine there is

no blockage or restriction, leakage, corrosion and

other deciencies which could cause an unsafe

condition.

3. Insofar as it is practical, close all building doors

and windows and all doors between the space in

which the appliances remaining connected to the

common venting system are located and other

spaces of the building. Turn on clothes dryers

and any appliance not connected to the common

venting system. Turn on any exhaust fans, such

as range hoods and bathroom exhausts, so they

will operate at maximum speed. Do not operate a

summer exhaust fan. Close replace dampers.

MIGHTY THERM2 Commercial Boilers and Volume Water Heaters

Page 13

OUTDOOR VENT OUTDOOR

SIZE TERMINAL COMBUSTION

AIR TERMINAL

500 20254703 CA014701

750 20254705 CA014702

1000 20254705 CA014702

1250 D2007700 CA014704

1500 D2007700 CA014704

1750 D2007800 CA014704

2000 D2007800 CA014704

Table 6. Vent Terminals for Outdoor Units.

4. Place in operation the appliance being inspected.

Follow the lighting instructions. Adjust thermostat

so that the heating unit will operate continuously.

5. Test for spillage at the draft hood relief opening

after 5 minutes of main burner operation. Use

the ame of a match or candle, or smoke from a

cigarette, cigar or pipe.

6. After it has been determined that each appliance

remaining connected to the common venting

system properly vents when tested as outlined

above, return doors, windows, exhaust fans,

replace dampers and any other gas burning

appliance to their previous conditions of use.

7. Any improper operation of the common venting

system should be corrected so that the installation

conforms to the National Fuel Gas Code, ANSI

Z223.1/NFPA 54 and/or CSA B149.1, Installation

Codes. When resizing any portion of the common

venting system, the common venting system

should be resized to approach the minimum size as

determined using the appropriate tables in Part II of

the National Fuel Gas Code, ANSI Z223.1/NFPA 54

and/or CSA B149.1, Installation Codes.

2.E Vent Terminals for Outdoor Units

For outdoor applications, the vent and combustion

air openings must be covered with proper terminals to

prevent rain, snow and other objects from falling into the

unit.

If local codes allow, outdoor installations may

use 1' of appropriately sized galvanized single wall or

B-Vent and a rain cap for exhaust vent termination in

the default conguration (venting out of the top). Note

that some local codes may require a higher vertical

vent height, extending above any perimeter fencing,

etc. In installations where the appearance of the vent is

objectionable, the low prole vent terminals in Table 6

may be used.

Combustion air inlets consist of appropriately

sized galvanized pipe and elbows to allow the open

end to face down aside the boiler. This is available as a

Commercial Kit from the manufacturer.

Part numbers for the low prole terminals to cover the

vent and combustion air openings are shown in Table 6.

LAARS Heating Systems

Page 14

SIZE DISTANCE FROM GAS METER

AND OR LAST STAGE REGULATOR

GAS TYPE 0-100' 100-200' 200-300'

500 natural 1½" 2" 2"

500 propane 1" 1½" 1½"

750 natural 2" 2" 2½"

750 propane 1½" 1½" 2"

1000 natural 2" 2½" 3"

1000 propane 1½" 2" 2½"

1250 natural 2½" 2½" 3"

1250 propane 2" 2" 2½"

1500 natural 2½" 3" 3"

1500 propane 2" 2½" 2½"

1750 natural 2½" 3" 3"

1750 propane 2" 2½" 2½"

2000 natural 3" 3" 3½"

2000 propane 2½" 2½" 3"

Metric Equivalent

SIZE DISTANCE FROM GAS METER

AND OR LAST STAGE REGULATOR

GAS TYPE 0-31m 31-61m 61-91m

500 natural 3.8cm 5.1cm 5.1cm

500 propane 2.5cm 3.8cm 3.8cm

750 natural 5.1cm 5.1cm 6.4cm

750 propane 3.8cm 3.8cm 5.1cm

1000 natural 5.1cm 6.4cm 7.6cm

1000 propane 3.8cm 5.1cm 6.4cm

1250 natural 6.4cm 6.4cm 7.6cm

1250 propane 5.1cm 5.1cm 6.4cm

1500 natural 6.4cm 7.6cm 7.6cm

1500 propane 5.1cm 6.4cm 6.4cm

1750 natural 6.4cm 7.6cm 7.6cm

1750 propane 5.1cm 6.4cm 6.4cm

2000 natural 7.6cm 7.6cm 8.9cm

2000 propane 6.4cm 6.4cm 7.6cm

NOTES: 1. These gures are based on 1/2" (0.12kPa) water column

pressure drop.

2. Check supply pressure and local code requirements

before proceeding with work.

3. Pipe ttings must be considered when determining gas

pipe sizing.

Table 7. Gas Piping Sizes.

SECTION 3 Gas Supply and Piping

3.A Gas Supply and Piping

Gas piping should be supported by suitable

hangers or oor stands, not by the boiler or water heater.

This units gas train allows the user to pipe the gas

from either the right side or the left side of the unit. As

shipped, the right side of the gas train is capped o, and

there is a manual valve on the left side. If desired, the

manual valve on the left side of the gas train may be

moved to the right side, and the cap on the right side

may be moved to the left.

Review the following instructions before proceeding

with the installation.

1. Verify that the unit is tted for the proper type of

gas by checking the rating plate. These units are

equipped to operate at elevations up to 10,000 feet

(3050m) and may be adjusted to operate properly

at altitudes above 2500 feet (see Section 6.F.2)

and the input will be reduced if the heating value of

the gas supply is below sea level values.

2. The maximum inlet gas pressure must not exceed

13" W.C (3.2kPa). The minimum inlet gas pressure

is 5" W.C. (1.2kPa).

3. Refer to Table 7, size supply.

4. Run gas supply line in accordance with all

applicable codes.

5. Locate and install manual shuto valves in

accordance with state and local requirements.

6. A sediment trap must be provided upstream of the

gas controls.

7. All threaded joints should be coated with piping

compound resistant to action of liqueed petroleum

gas.

8. The unit and its individual shuto valve must be

disconnected from the gas supply piping during any

pressure testing of that system at test pressures in

excess of 1/2 PSIG (3.45kpa).

9. The unit must be isolated from the gas supply

system by closing its individual manual shuto

valve during any pressure testing of the gas supply

piping system at test pressures equal to or less

than 1/2 PSIG (3.45kpa).

10. The unit and its gas connection must be leak tested

before placing it in operation.

11. Purge all air from gas lines.

NOTE: This unit and all other gas appliances sharing

the gas supply line must be ring at maximum capacity

to properly measure the inlet supply pressure. The

pressure can be measured at the supply pressure

port on the gas valve. Low gas pressure could be an

indication of an undersized gas meter, undersized gas

supply lines and/or an obstructed gas supply line.

WARNING

Do not use open ame to check for leaks. An

open ame could lead to explosion, which could result

in property damage, serious injury or death.

WARNING

If an inline high gas pressure regulator is used, it

must be of the lockup type and located a minimum

of 10 feet from the unit. Failure to do so may result in

insucient gas volume supplied to the unit.

MIGHTY THERM2 Commercial Boilers and Volume Water Heaters

Page 15

Unit

20°F 25°F 30°F 35°F

Size ow H/L ow H/L ow H/L ow H/L

gpm feet gpm feet gpm feet gpm feet

500 43 1.7 34 1.1 28 0.9 24 0.7

750 64 3.3 51 2.3 43 1.7 36 1.2

1000 85 5.0 68 3.6 57 3.1 49 2.2

1250 106 8.1 85 6.1 71 4.7 61 3.4

1500 128 10.0 102 7.2 85 5.5 73 4.2

1750 N/R N/R 119 10.5 99 8.4 85 5.8

2000 N/R N/R 136 12.5 113 10.4 97 8.3

Metric Equivalent

Unit

11°C 14°C 17°C 19°C

Size ow H/L ow H/L ow H/L ow H/L

lpm m lpm m lpm m lpm m

500 161 0.5 129 0.3 107 0.3 92 0.2

750 241 1.0 193 0.7 161 0.5 138 0.4

1000 321 1.5 257 1.1 214 0.9 184 0.7

1250 401 2.5 322 1.9 269 1.4 231 1.0

1500 483 3.0 386 2.2 322 1.7 276 1.3

1750 N/R N/R 451 3.2 375 2.6 322 1.8

2000 N/R N/R 515 3.8 429 3.2 368 2.5

Notes: gpm = gallons per minute, lpm = liters per minute,

H/L = headloss, ft = headloss in feet, m = headloss in meters.

Maximum temperature rise is 35°F (19°C), as shown. Headloss is

for boiler’s heat exchanger only. N/R = not recommended.

Table 8. Water Flow Requirements — Boilers.

Figure 5. Typical Gas Train Conguration.

SECTION 4 Water Connections

4.A Boilers.

4.A.1 Heating System Piping:

Hot Supply Connections — Boiler

NOTE: This unit must be installed in a closed pressure

system with a minimum of 12 psi (82.7kPa) static

pressure at the boiler.

Hot water piping should be supported by suitable

hangers or oor stands. Do not support piping with this

unit. Due to expansion and contraction of copper pipe,

consideration should be given to the type of hangers

used. Rigid hangers may transmit noise through the

system resulting from the piping sliding in the hangers.

It is recommended that padding be used when rigid

hangers are installed. Maintain 1" clearance to

combustibles for hot water pipes.

Pipe the discharge of the relief valve (full size)

to a drain or in a manner to prevent injury in the event

of pressure relief. Install an air purger, an air vent, a

diaphragm-type expansion tank, and a hydronic ow

check in the system supply loop. Minimum ll pressure

must be 12psig (82.7kPa). Install shuto valves where

required by code.

Suggested piping diagrams are shown (see Fig-

ures 6 through 10). These diagrams are meant only as

a guide. Components required by local codes must be

properly installed.

4.A.2 Cold Water Make-Up — Boiler

1. Connect the cold water supply to the inlet

connection of an automatic ll valve.

2. Install a suitable back ow preventer between the

automatic ll valve and the cold water supply.

3. Install shut o valves where required.

NOTE: This boiler, when used in connection with a

refrigeration system, must be installed so the chilled

medium is piped in parallel with the boiler with

appropriate valves to prevent the chilled medium from

entering the boiler.

The boiler piping system of a hot water heating

boiler connected to heating coils located in air handling

appliances where they may be exposed to refrigerated

air circulation must be equipped with ow control valves

or other automatic means to prevent gravity circulation of

the boiler water during the cooling cycle.

A boiler installed above radiation level, or as

required by the authority having jurisdiction, must be

provided with a low water cuto device either as a part of

the boiler or at the time of boiler installation.

4.A.3 Water Flow Requirements — Boiler

A hydronic heating (closed loop) application

re-circulates the same uid in the piping system. As a

result, no new minerals or oxygen is introduced into

the system. To ensure a proper operating temperature

leading to long boiler life, a ow rate has been

established based on the uid temperature rise for this

specic size boiler.

Pump-mounted boilers can be ordered for use in

primary secondary piping systems. The pumps used are

sized for the headloss through the heater, plus 30 feet

(9.1m) of full-sized piping (same size as boiler outlet)

and a normal number of ttings.

LAARS Heating Systems

Page 16

Table 8 species water ow rates for boilers, which

will enable the user to size a pump. The headloss shown

is for the heater only, and the user will need to add the

headloss of the system piping to properly size the pump.

The minimum inlet water temperature for the this

unit is 120°F (49°C) to avoid condensing on the copper

coils.

4.A.4 Freeze Protection — Boiler

Boiler installations are not recommended in areas

where the danger of freezing exists unless proper

precautions are made for freeze protection. A non

toxic, heating system, anti-freeze may be added to

the hydronic system provided that the concentration

does not exceed 50% and the anti freeze contains an

anti foamant. When a 50/50 mixture is used, increase

the water ow requirements by 15%, and increase the

headloss requirements by 20%.

Power outage, interruption of gas supply, failure

of system components, activation of safety devices,

etc., may prevent a boiler from ring. Any time a boiler

is subjected to freezing conditions, and the boiler is not

able to re, and/or the water is not able to circulate,

there is a risk of freezing in the boiler or in the pipes in

the system. When water freezes, it expands. This can

result in bursting of pipes in the system, or damage

to the boiler, which could result in leaking or ooding

conditions.

NOTE: Dierent glycol products may provide varying

degrees of protection. Glycol products must be

maintained properly in a heating system, or they may

become ineective. Consult the glycol specications,

or the glycol manufacturer, for information about

specic products, maintenance of solutions, and set up

according to your particular conditions.

4.B Water Connections —

Water Heaters

4.B.1 Water System Piping — Water Heater

Hot water piping should be supported by suitable

hangers or oor stands. Do not support piping with this

unit. Due to expansion and contraction of copper pipe,

consideration should be given to the type of hangers

used. Rigid hangers may transmit noise through the

system resulting from the piping sliding in the hangers.

It is recommended that padding be used when rigid

hangers are installed.

This unit can be used with several dierent types

of readily available storage tanks. A pump draws water

from the storage tank and pumps the water through the

heater and back into the tank. Pump-mounted units have

a circulating pump built into the water heater. The pumps

used are sized for the headloss through the heater, plus

30 feet (9.1m) of full-sized piping (same size as boiler

outlet) and a normal number of ttings. Pumps used on

pump-mounted unit are sized for soft/normal or hard

water, so make sure a pump-mounted unit matches the

water quality of the installation.

Pipe the outlet from the heater’s relief valve such

that any discharge from the relief valve will be conducted

to a suitable place for disposal when relief occurs. Do

not reduce line size or install any valves in this line. The

line must be installed to allow complete drainage of both

the valve and the line.

Suggested piping diagrams are shown in Figures

11 through 14. These diagrams are meant only as a

guide. Components required by local codes must be

properly installed.

The minimum inlet water temperature for this unit is

120°F (49°C) to avoid condensing on the copper coils.

4.B.2 Hot Water Supply Piping — Water Heater

Follow the tank manufacturer’s guidelines for

completion of the hot water system connections.

NOTE: A temperature and pressure relief valve, listed

as complying with the Standard for Relief Valves

and Automatic Gas Shuto Devices for Hot Water

Supply Systems (ANSI Z21.22 / CSA 4.4) of suitable

discharge capacity, must be installed in the separate

storage tank system.

If this water heater is installed in a closed water

supply system, such as one having a backow preventer

in the cold water supply line, the relief valve may

discharge periodically, due to thermal expansion. A

properly-sized expansion tank (or other means) must be

provided to control thermal expansion. Contact the water

supplier or local plumbing inspector on how to control

this situation.

4.B.3 Water Flow Requirements — Water Heater

In a water heating application (an open system),

new water is constantly being introduced. With the

new water comes a fresh supply of minerals that can

be deposited on the units heat exchanger. This is

commonly known as scaling. The amount of minerals

will depend upon the hardness of the water. Water can

also be aggressive, and can erode metals, including

copper, if the water is moved too quickly. The water ow

requirements for this units water heater are based upon

the hardness of the water. The water ow is kept high

enough to prevent scaling, but low enough to prevent

tube erosion. For extremely soft or hard water, cupro-

nickel tubes are available. Contact a manufacturers

representative if you have questions or concerns about

water quality.

Pump-mounted water heaters can be ordered

with standard pumps for soft or normal water or with

pumps for hard water. The pumps used are sized for the

headloss through the heater, plus 30 feet (9.1m) of full-

Page is loading ...

Laars MT2H0750NACK1CJX Installation guide

Brand: Laars

Model: MT2H0750NACK1CJX

Type: Installation guide

This manual is also suitable for

Download PDF

report

Laars MT2H0750NACK1CJX Installation guide

This manual is also suitable for

Laars MT2H0750NACK1CJX Installation guide

Related papers

Other documents