Fischer 63298 Owner's manual

Brand: Fischer

Model: 63298

Type: Owner's manual

This manual is also suitable for

Item 63298-UPC 193175358295

Fischer 63298 is a versatile and powerful tool that can lift vehicles weighing up to 750 pounds. It features a maximum lift height of 23 inches and a wheel bracket width that can be adjusted from 40-3/8 inches to 56-1/8 inches center to center. The Fischer 63298 is easy to assemble and use, and it comes with a variety of safety features, including a safety lock lever and a release pedal.

!"#"$%&'(%)*+#"$*%,$-%.$$/-00)))1.,(+&(2(*"3.$14&5

65,"7%&'(%$*4.8"4,7%#'//&($%,$-%/(&9'4$#'//&($:.,(+&(2(*"3.$14&5

Owner’s Manual & Safety Instructions

Save This Manual Keep this manual for the safety warnings and precautions, assembly,

operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the

back of the manual near the assembly diagram (or month and year of purchase if product has no number).

Keep this manual and the receipt in a safe and dry place for future reference. 20h

When unpacking, make sure that the product is intact

and undamaged. If any parts are missing or broken,

please call 1-888-866-5797 as soon as possible.

2020 by Harbor Freight Tools

No portion of this manual or any artwork contained herein may be reproduced in

any shape or form without the express written consent of Harbor Freight Tools.

Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein.

Tools required for assembly an d se rv ic e may n ot b e in cl uded.

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

Page 2 ;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1 Item 63298

EF;6GH IJ6KFGLIM NFLMG6MFMO6FEE6NPQH

E/*4"2"4,$"&8#

Rated Capacity 750 lb

Maximum Lift Height 23"

Wheel Bracket Width

40-3/8" – 56-1/8"

center to center

LNJIKGFMG%EF;6GH%LM;IKNFGLIM

;,"7'(*%$&%.**9%$.*#*%),(8"83#%5,R%(*#'7$%"8%/*(#&8,7%"8S'(R%,890&(%/(&/*($R%9,5,3*-

F##*5+7R%J(*4,'$"&8#

1. Assemble only according to these instructions.

Improper assembly can create hazards.

2. Wear ANSI-approved safety goggles and

heavy-duty work gloves during assembly.

3. Keep assembly area clean and well lit.

4. Keep bystanders out of the area during assembly.

5. Do not assemble when tired or when under the

influence of alcohol, drugs or medication.

6. Weight capacity and other product capabilities apply

to properly and completely assembled product only.

T#*%J(*4,'$"&8#

1. Study, understand, and follow all instructions

before operating this device.

2. Do not exceed rated capacity.

3. Use only on hard, level surfaces.

4. Center load on Lift platforms.

5. Only lift tires using Wheel Brackets.

6. Immediately after lifting load, ensure Lift

mechanical load holding means is engaged.

7. Do not move while loaded.

8. Secure load with appropriate restraint device.

9. Do not adjust safety valve.

10. Wear ANSI-approved safety goggles and

heavy-duty work gloves during use.

11. Keep clear of load while lifting and lowering.

12. Lower load slowly.

13. Do not use for aircraft purposes.

14. Inspect before every use; do not use

if parts loose or damaged.

15. Keep your work area clean and well lit.

Cluttered work areas invite accidents.

16. Do not allow anyone on the vehicle while

using the Lift. Keep bystanders a safe

distance away from the vehicle and Lift.

17. Do not lift more than one vehicle at a time.

18. Stay alert. Watch what you are doing, and

use common sense when operating a jack.

Do not use a jack while tired or under the

influence of drugs, alcohol, or medication. A

moment of inattention while operating jacks

may result in serious personal injury.

19. Store idle jacks out of reach of children

and other untrained persons. Jacks are

dangerous in the hands of untrained users.

20. Jack service must be performed only by

qualified repair personnel. Service or

maintenance performed by unqualified

personnel could result in a risk of injury.

21. When servicing a jack, use only identical

replacement parts. Follow instructions in the

“Maintenance and Servicing” section of this manual.

Use of unauthorized parts or failure to follow

maintenance instructions may create a risk of injury.

22. Maintain labels and nameplates. These carry

important information. If unreadable or missing,

contact Harbor Freight Tools for a replacement.

23. Before use, read manufacturer’s instruction

manual for the vehicle you will lift.

24. Do not support both ends of the

vehicle at the same time.

25. Before lowering the Lift, remove all tools

and equipment from under the vehicle.

26. The warnings, precautions, and instructions

discussed in this manual cannot cover all

possible conditions and situations that may occur.

The operator must understand that common sense

and caution are factors, which cannot be built into

this product, but must be supplied by the operator.

%EF!6%GU6E6%LMEGKTOGLIME1

Page 3;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1Item 63298

EF;6GHIJ6KFGLIMNFLMG6MFMO6 FEE6NPQH

F##*5+7R%L8#$('4$"&8#

K*,9%$.*%6MGLK6%LNJIKGFMG%EF;6GH%LM;IKNFGLIM%#*4$"&8%,$%$.*%+*3"88"83%&2%$."#%9&4'5*8$%

"847'9"83%,77%$*V$%'89*(%#'+.*,9"83#%$.*(*"8%+*2&(*%#*$%'/%&(%'#*%&2%$."#%/(&9'4$1

1. Place the Base (2) flat on a horizontal surface.

Place the Upper Lift Arm Assembly onto the end of the Base

as shown and align the bolt holes.

Secure the Upper Lift Arm Assembly to the Base using two Bolts (6),

Flat Washers (8), Lock Washers (9), and Nuts (10).

P&7$%WAX

M'$%W>YX

Q&4Z%Q&4Z%

[,#.*(%[,#.*(%

WDXWDX

;7,$%;7,$%

[,#.*(%[,#.*(%

W@XW@X

T//*(%T//*(%

Q"2$%F(5%Q"2$%F(5%

F##*5+7RF##*5+7R

P,#*%P,#*%

W\XW\X

E$*/%>-%%F$$,4.%T//*(%Q"2$%F(5%F##*5+7R%$&%P,#*

2. Place the two Support Bars (11) as shown and align with the bolt holes in

the Base. Note that flat sides of Bars must align against Base as shown.

Attach the Support Bars to the Base using one Bolt (7),

Flat Washer (8), Lock Washer (9), and Nut (10) per bar.

Finger tighten the hardware.

P&7$%WCX

M'$%W>YX

Q&4Z%Q&4Z%

[,#.*(%WDX[,#.*(%WDX

;7,$%;7,$%

[,#.*(%[,#.*(%

W@XW@X

E'//&($%E'//&($%

P,(%%P,(%%

W>>XW>>X

P,#*%P,#*%

W\XW\X

E$*/%\-%%F$$,4.%E'//&($%P,(#%$&%P,#*

Page 4 ;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1 Item 63298

EF;6GH IJ6KFGLIM NFLMG6MFMO6FEE6NPQH

3. Remove the R-Clip (23) and Flat Washer (8) from one end of the Short Lift Arm Rod (25).

Remove the Cotter Pin (12) and Flat Washer (8) from one end of the Long Lift Arm Rod (24).

Place the Lower Lift Arm (21) in position, then insert the Short Lift Arm Rod through the

bracket on the Upper Lift Arm Assembly (26) and the front end of the Lower Lift Arm.

Replace the Washer over the end of the Short Lift Arm Rod and use an R-Clip to secure the Rod in place.

Raise up the previously installed Support Bars. Insert the Long Lift Arm Rod through the Support Bar, the

shaft of the Upper Lift Arm Assembly, the rear end of the Lower Lift Arm, and the other Support Bar.

Replace the Washer over the end of the Long Lift Arm Rod and insert the

Cotter Pin and bend it over to secure the Rod in place.

Q&)*(%Q"2$%Q&)*(%Q"2$%

F(5%W\>XF(5%W\>X

T//*(%Q"2$%F(5%T//*(%Q"2$%F(5%

F##*5+7R%E.,2$F##*5+7R%E.,2$

E.&($%Q"2$%F(5%K&9%W\BXE.&($%Q"2$%F(5%K&9%W\BX

Q&83%Q"2$%F(5%K&9%W\]XQ&83%Q"2$%F(5%K&9%W\]X

E'//&($%E'//&($%

P,(%W>>XP,(%W>>X

O&$$*(%O&$$*(%

J"8%W>\XJ"8%W>\X

K?O7"/%K?O7"/%

W\^XW\^X

[,#.*(%

W@X

[,#.*(%W@X[,#.*(%W@X

Q&)*(%Q"2$%F(5%Q&)*(%Q"2$%F(5%

"8%/7,4*"8%/7,4*

E'//&($%P,(%E'//&($%P,(%

"8%/7,4*"8%/7,4*

E.&($%Q"2$%F(5%K&9%%E.&($%Q"2$%F(5%K&9%%

,$$,4.5*8$,$$,4.5*8$

Q&83%Q"2$%F(5%K&9%Q&83%Q"2$%F(5%K&9%

,$$,4.5*8$,$$,4.5*8$

T//*(%Q"2$%F(5%T//*(%Q"2$%F(5%

F##*5+7RF##*5+7R

E$*/%^-%%F$$,4.%Q&)*(%Q"2$%F(5%$&%T//*(%Q"2$%F(5%F##*5+7R%,89%E'//&($%P,(#

Page 5;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1Item 63298

EF;6GHIJ6KFGLIMNFLMG6MFMO6 FEE6NPQH

4. Insert Cross Beam (33) through the bracket on the Upper Lift Arm Assembly as shown and align bolt holes.

Insert Cross Beam Pin (36) through center of bracket and Cross Beam.

Secure Cross Beam Pin in place with R-Clip (23).

T//*(%Q"2$%%

F(5%F##*5+7R

O(&##%P*,5%J"8%W^AX

O(&##%P*,5%W^^X

K?O7"/%W\^X

E$*/%]-%%F$$,4.%O(&##%P*,5

5. Slide one Wheel Bracket (34) over each end of the Cross Beam (33).

Insert Width Pins (31) to secure them in place.

Remove the R-Clip (23) and Flat Washer (29) from one end of each Wheel Bracket Rod (32).

Insert one Wheel Bracket Rod through the holes on each Wheel Bracket.

Replace the R-Clip and Flat Washer on the end of each Wheel Bracket Rod to secure the Rods in place.

["9$.%J"8%W^>X

[.**7%P(,4Z*$%W^]X

O(&##%P*,5%W^^X

[.**7%

P(,4Z*$%

K&9%W^\X

;7,$%

[,#.*(%

W\DX

K?O7"/%

W\^X

E$*/%B-%%L8#$,77%[.**7%P(,4Z*$#%,89%F$$,4.%[.**7%P(,4Z*$%K&9#

Page 6 ;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1 Item 63298

EF;6GH IJ6KFGLIM NFLMG6MFMO6FEE6NPQH

6. Insert the Foot Pedal (40) into its holder on the Ram (43).

Secure the Foot Pedal in place using the Lock Washer (42) and Foot Pedal Bolt (41)

through the side of its holder.

Position the Ram in Upper Lift Arm / Shaft Assembly as shown.

Slide Lower (Long) Ram Pin (39) through the shaft bracket and the clevis base of the Ram.

Slide Upper (Short) Ram Pin (38) through the bracket on the Lower Lift Arm (21) and the top of the Ram.

Place a Washer (8) over both ends of each Pin.

Secure both ends of each Pin with R-Clips (23).

Q&4Z%Q&4Z%

[,#.*(%[,#.*(%

W]\XW]\X

T//*(%K,5%J"8%W^@X%T//*(%K,5%J"8%W^@X%

)"$.%[,#.*(#%W@X%)"$.%[,#.*(#%W@X%

,89%K?O7"/#%W\^X,89%K?O7"/#%W\^X

Q&)*(%K,5%J"8%W^DX%Q&)*(%K,5%J"8%W^DX%

)"$.%[,#.*(#%W@X%)"$.%[,#.*(#%W@X%

,89%K?O7"/#%W\^X,89%K?O7"/#%W\^X

;&&$%J*9,7%W]YX

;&&$%J*9,7%P&7$%W]>X

T//*(%K,5%T//*(%K,5%

J"8J"8

Q&)*(%Q&)*(%

K,5%J"8K,5%J"8

K,5%E*4'(*9%K,5%E*4'(*9%

L8%J7,4*L8%J7,4*

E$*/%A-%%F$$,4.%;&&$%J*9,7%,89%L8#$,77%K,5

Page 7;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1Item 63298

EF;6GHIJ6KFGLIMNFLMG6MFMO6 FEE6NPQH

7. Insert the Handle (22) into the bracket on the Lift Arm / Shaft Assembly and align the upper and lower holes.

Secure in place using two Handle Bolts (17), Lock Washers (18), and Flat Washers (19).

U,897*%W\\X

U,897*%P&7$%W>CX%U,897*%P&7$%W>CX%

Q&4Z%[,#.*(%W>@X%Q&4Z%[,#.*(%W>@X%

;7,$%[,#.*(%W>DX;7,$%[,#.*(%W>DX

E$*/%C-%%L8#$,77%U,897*

8. Insert the Wheels (1) into the wheel brackets on the rear of the Base (2) and align the holes.

Secure Wheels in place using Wheel Bolts (3) and Nuts (4).

[.**7%

P&7$%W^X

[.**7%W>X

[.**7%

P(,4Z*$

P,#*%W\X

M'$%W]X

E$*/%@-%%F$$,4.%[.**7#

Page 8 ;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1 Item 63298

EF;6GH IJ6KFGLIM NFLMG6MFMO6FEE6NPQH

O&5/&8*8$#

;7'"9%;"77%

U&7*

;7'"9%;"77%

J7'3

K,5

U,897*

E,2*$R%

Q&4Z%Q*_*(

E,2*$R%Q&4Z%

Q*_*(

;&&$%

J*9,7

K*7*,#*%

J*9,7

[.**7%

P(,4Z*$

[.**7%

P(,4Z*$%K&9

[.**7%

P(,4Z*$%K&9

[.**7%P(,4Z*$

G"*?`&)8%

P(,4Z*$

["9$.%J"8

E,2*$R%Q&4Z%Q*_*(#%"8%

QIOa6`%/&#"$"&81

E,2*$R%Q&4Z%Q*_*(#%"8%

TMQIOa6`%/&#"$"&81

Page 9;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1Item 63298

EF;6GHIJ6KFGLIMNFLMG6MFMO6 FEE6NPQH

I/*(,$"83%L8#$('4$"&8#

K*,9%$.*%*8$"(*%L5/&($,8$%E,2*$R%L82&(5,$"&8%#*4$"&8%,$%$.*%+*3"88"83%&2%$."#%9&4'5*8$%"847'9"83%,77%

$*V$%'89*(%#'+.*,9"83#%$.*(*"8%+*2&(*%#*$%'/%&(%'#*%&2%$."#%/(&9'4$1

P7**9"83

LNJIKGFMGb%%P*2&(*%2"(#$%'#*=%4.*4Z%2&(%/(&/*(%.R9(,'7"4%27'"9%7*_*7%"8%$.*%K,51%%%

G.*8%$.&(&'3.7R%$*#$%$.*%Q"2$%2&(%/(&/*(%&/*(,$"&8%/("&(%$&%"$#%,4$',7%'#*1%%%

L2%$.*%Q"2$%,//*,(#%not%$&%+*%)&(Z"83%/(&/*(7R=%"$%5,R%+*%8*4*##,(R%

$&%bleed%"$#%.R9(,'7"4%#R#$*5%&2%*V4*##%,"(1

1. Have an assistant hold the Release Pedal down.

2. Pump the Foot Pedal quickly several times.

3. Test the Lift several times for proper operation

before attempting to lift a load. L2%$.*%Q"2$%#$"77%

9&*#%not ,//*,(%$&%+*%)&(Z"83%/(&/*(7R%,2$*(%

+7**9"83=%9&%8&$%'#*%$.*%Q"2$%'8$"7%"$%.,#%+**8%

(*/,"(*9%+R%,%<',7"2"*9%#*(_"4*%$*4.8"4",81

Q"2$"83

[FKMLMcb%%E*$%Q"2$%,89%_*."47*%&8%,%27,$=%7*_*7=%.,(9=%3(&'89%#'(2,4*%#,2*7R%,),R%2(&5%&84&5"83%

$(,22"41%%G'(8%&22%_*."47*d#%*83"8*1% Also place the vehicle’s transmission in “PARK” (if automatic) or in its

lowest gear (if manual). Set the vehicle’s emergency brake. Then, block the wheels that are not being lifted.

1. Determine the wheel width of the vehicle,

and adjust the Wheel Bracket supports to

match that width. Lock them in place using

the Width Pins.%%[FKMLMcb%%GI%JK6!6MG%

E6KLITE%LMeTKH-%F9S'#$%$.*5%#&%$.,$%$.*R%

,(*%*<',77R%9"#$,8$%2(&5%$.*%4*8$*(%&2%$.*%Q"2$=%

&(%*7#*%$.*%Q"2$%)"77%+*%'8#$,+7*%,89%5"3.$%$"/1

2. Examine the bottom of each vehicle wheel that

is touching the floor. Set the depth of both

Wheel Brackets to be slightly larger than that

distance by adjusting the Wheel Bracket Rods.

3. Press the Release Pedal to lower the Lift.

Once the Lift is fully lowered,

release the Release Pedal.

4. Use the vehicle’s steering to straighten its wheels.

Use wheel chocks (sold separately) to block the

wheels on the opposite side of the vehicle.

5. Press the fronts of the Wheel Brackets straight

against the fronts of the vehicle’s wheels.

Push the Wheel Brackets under the wheels until

both wheels rest in the center of the Wheel Bracket.

6. [FKMLMcb%GI%JK6!6MG%E6KLITE%LMeTKH%FM`%

`6FGU-%J7,4*%$.*%$)&%E,2*$R%Q&4Z%Q*_*(#%"8%$.*%

47&#*9=%7&4Z*9%/&#"$"&8%$&%*8,+7*%$.*%7&4Z"83%

5*4.,8"#51%%K*2*(%$&%O&5/&8*8$#%&8%/,3*%@1

7. [FKMLMcb%GI%JK6!6MG%E6KLITE%LMeTKH%FM`%

`6FGU-%T#*%$"*?9&)8%#$(,/#%W#&79%#*/,(,$*7RX%

$&%#*4'(*%$.*%7&,9%$&%$.*%G"*?`&)8%P(,4Z*$1%%

U&79%$.*%U,897*%,89%/'5/%$.*%;&&$%J*9,71%%

T#*%#5&&$.=%2'77%#$(&Z*#%2&(%+*#$%(*#'7$#1

8. Raise the vehicle to the desired height. As the load

is lifted the locking mechanism will automatically

engage to lock the Lift Arm in one of three positions.

9. Make sure the Lift Arm is locked in one of the three

available positions before working on the vehicle.

Q&)*("83

1. Remove all tools, parts, etc. from under the vehicle.

2. Pump the Foot Pedal slightly to remove

weight from the locking mechanism.

3. Place the two Safety Lock Levers in the horizontal,

unlocked position to disengage the locking

mechanism. Refer to Components on page 8.

4. Keep clear while pressing the Release Pedal

slowly to lower the vehicle.

5. Once the Lift is completely lowered,

remove the tie-down straps and remove

the Lift from under the vehicle.

6. When not in use, store Lift in a safe, dry

location out of reach of children.

Page 10 ;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1 Item 63298

EF;6GH IJ6KFGLIM NFLMG6MFMO6FEE6NPQH

N,"8$*8,84*%,89%E*(_"4"83

J(&4*9'(*#%8&$%#/*4"2"4,77R%*V/7,"8*9%"8%$."#%5,8',7%5'#$%+*%/*(2&(5*9%&87R%+R%,%<',7"2"*9%$*4.8"4",81

GI%JK6!6MG%E6KLITE%LMeTKH%;KIN%FOOL`6MGFQ%IJ6KFGLIM-%`&%8&$%'#*%9,5,3*9%*<'"/5*8$1%%

L2%,+8&(5,7%8&"#*%&(%_"+(,$"&8%&44'(#=%.,_*%$.*%/(&+7*5%4&((*4$*9%+*2&(*%2'($.*(%'#*1

O7*,8"83=%N,"8$*8,84*=%,89%Q'+("4,$"&8

1. P6;IK6%6FOU%TE6=%inspect the general

condition of the Lift. Check for:

• broken, cracked, or bent parts

• loose or missing parts

• any other condition that may

affect its safe operation.

If a problem occurs, have the problem

corrected before further use.%%

`&%8&$%'#*%9,5,3*9%*<'"/5*8$1

2. P*2&(*%*,4.%'#*=%$.&(&'3.7R%$*#$%$.*%Q"2$%

2&(%/(&/*(%&/*(,$"&8%/("&(%$&%"$#%,4$',7%'#*1%%

L2%$.*%Q"2$%,//*,(#%not%$&%+*%)&(Z"83%/(&/*(7R=%

2&77&)%Bleeding%"8#$('4$"&8#%&8%/,3*%D1

3. O.,83*%$.*%.R9(,'7"4%27'"9%,$%7*,#$%

&84*%*_*(R%$.(**%R*,(#-

a. With the Lift fully lowered, remove the Fluid

Fill Plug on the side of the Ram housing.

b. With assistance, tip the Lift to allow the old

hydraulic fluid to drain out of the Ram housing

completely, and dispose of the old hydraulic

fluid in accordance with local regulations.

c. With the Lift upright, completely fill the

Ram housing with a high quality hydraulic

fluid (not included) until the fluid just

begins to run out of the Fluid Fill Hole.

d. Then reinstall the Fluid Fill Plug.

4. Clean with a clean cloth with a detergent

or mild solvent. Store the Lift in a safe,

dry location out of reach of children1

Page 11;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1Item 63298

EF;6GHIJ6KFGLIMNFLMG6MFMO6 FEE6NPQH

G(&'+7*#.&&$"83

GI%JK6!6MG%E6KLITE%LMeTKH-%T#*%4,'$"&8%).*8%$(&'+7*#.&&$"83%,%5,72'84$"&8"83%S,4Z1%%%

E$,R%)*77%47*,(%&2%$.*%#'//&($*9%7&,91%%O&5/7*$*7R%(*#&7_*%,77%/(&+7*5#%+*2&(*%'#*1

If the solutions presented in the Troubleshooting guide do not solve the problem, have a qualified technician

inspect and repair the jack before use. F2$*(%$.*%S,4Z%"#%(*/,"(*9-%%G*#$%"$%4,(*2'77R%)"$.&'$%,%7&,9%+R%(,"#"83%

"$%,89%7&)*("83%"$%2'77R=%4.*4Z"83%2&(%/(&/*(%&/*(,$"&8=%P6;IK6%K6GTKMLMc%GU6%eFOa%GI%IJ6KFGLIM1

`I%MIG%TE6%F%`FNFc6`%IK%NFQ;TMOGLIMLMc%eFOab

JIEELPQ6%EHNJGINE

JKIPFPQ6%EIQTGLIM

WN,Z*%4*($,"8%$.,$%$.*%S,4Z%"#%8&$%#'//&($"83%

,%7&,9%)."7*%,$$*5/$"83%,%#&7'$"&81X

Jack will

not lift at

its weight

capacity

Lift Arm

lowers

under

load

Pump

stroke

feels

spongy

Lift Arm

will not

lift all the

way

Pedal

moves up

when jack

is under

load

Fluid

leaking

from fill

plug

f f

Check that Release Pedal is not

stuck and raises completely.

f f f

Valves may be blocked and may not close fully.

To flush the valves, with assistance:

1. Lower the Lift Arm and release the Release Pedal.

2. Manually lift the Lift Arm several inches.

3. Press the Release Pedal and force

the Lift Arm down quickly.

f f f

Ram may be low on fluid. Check the fluid level and

refill if needed.

Ram may require bleeding – refer

to Bleeding on page 9.

Unit may have too much hydraulic fluid inside.

Check fluid level and adjust if needed.

Page 12 ;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1 Item 63298

EF;6GH IJ6KFGLIM NFLMG6MFMO6FEE6NPQH

J,($#%Q"#$%,89%`",3(,5

JQ6FE6%K6F`%GU6%;IQQI[LMc%OFK6;TQQH

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM

IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR

MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS

QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE

ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY

STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND

LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY

ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS

THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Page 13;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1Item 63298

EF;6GHIJ6KFGLIMNFLMG6MFMO6 FEE6NPQH

K*4&(9%J(&9'4$d#%E*(",7%M'5+*(%U*(*-%

M&$*- If product has no serial number, record month and year of purchase instead.

M&$*- Some parts are listed and shown for illustration purposes only, and are not available

individually as replacement parts. Specify UPC 193175358295 when ordering parts.

Page 14 ;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1 Item 63298

EF;6GH IJ6KFGLIM NFLMG6MFMO6FEE6NPQH

J,($#%Q"#$%,89%`",3(,5

J,($#%Q"#$

J,($ `*#4("/$"&8 g$R

1 Wheel 2

2 Base 1

3 Wheel Bolt M12 x 100 2

4 Nut M12 2

5 Large End Cap 6

6 Bolt M12 x 95 2

7 Bolt M12 x 65 2

8 Flat Washer 15

9 Lock Washer 4

10 Nut M12 4

11 Support Bar 2

12 Cotter Pin 2

13 Safety Lock Lever 2

14 Rivet 2

15 Spring 2

16 Pin 2

17 Handle Bolt M10 x 20 2

18 Lock Washer 2

19 Flat Washer 2

20 Shaft 1

21 Lower Lift Arm 1

22 Handle 1

J,($ `*#4("/$"&8 g$R

23 R-Clip 13

24 Long Lift Arm Rod 1

25 Short Lift Arm Rod 1

26 Upper Lift Arm 1

27 Rubber Pad 3

28 Screw 4

29 Flat Washer 4

30 Small End Cap 4

31 Width Pin 2

32 Wheel Bracket Rod 2

33 Cross Beam 1

34 Wheel Bracket 2

35 Plate 1

36 Cross Beam Pin 1

37 Handle End Cap 1

38 Upper Ram Pin 1

39 Lower Ram Pin 1

40 Foot Pedal 1

41 Foot Pedal Bolt M8 x 16 1

42 Lock Washer 1

43 Ram 1

Page 15;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1Item 63298

EF;6GHIJ6KFGLIMNFLMG6MFMO6 FEE6NPQH

F##*5+7R%`",3(,5

\AB]>%F3&'(,%K&,9%%h%%O,7,+,#,#=%OF%D>^Y\%%h%%>?@@@?@AA?BCDC

Q"5"$*9%DY%`,R%[,((,8$R

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,

and warrants to the original purchaser that this product is free from defects in materials and workmanship for the

period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,

to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper

installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries

to persons or property, or for incidental, contingent, special or consequential damages arising from the use of

our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the

above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER

WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation charges

prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.

If our inspection verifies the defect, we will either repair or replace the product at our election or we may

elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will

return repaired products at our expense, but if we determine there is no defect, or that the defect resulted

from causes not within the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

Fischer 63298 Owner's manual

Brand: Fischer

Model: 63298

Type: Owner's manual

This manual is also suitable for

Item 63298-UPC 193175358295

Download PDF

report

Fischer 63298 Owner's manual

This manual is also suitable for

Fischer 63298 Owner's manual

Related papers

Other documents