Lenovo Star Wars Setup Manual

Brand: Lenovo

Model: Star Wars

Type: Setup Manual

Set-up Guide

1. Before you start

2. Get your gear ready

Make sure your phone is compatible

at jedichallenges.com/compatibility .

• Lenovo Mirage AR headset

• Phone tray ( inserted in the headset )

• Tracking Beacon

• 2 x AA batteries

• Lightsaber Controller

• Your compatible smartphone

• The matching phone-to-headset

Getting

Ready

1 2

1. GET YOUR COMPATIBLE PHONE READY 2. OPTIMIZING YOUR PHONE SETTINGS :

(1) Disable adaptive brightness in settings / display

(2) Set Brightness level to maximum in settings / display

(3) Turn on location in settings / location

(4) Set location to high accuracy in settings / location / mode

(5) Turn on Bluetooth in settings / Bluetooth

(6) Set media volume to above 70%

Setting Up

the Phone

4 5

(1) Make sure the phone is connected to WiFi.

(2) Go to jedichallenges.com/app with your phone browser

and follow the instructions to download, or search for the

Star Wars: Jedi Challenges app on the application store

on your phone. Download and install the application

3 4

1. OPEN THE APP

Setting Up

the Experience

5 6

And tap the screen to continue.

3. TURN ON

THE LIGHTSABER

2. ADJUST THE VOLUME

Turn on the Bluetooth on your

phone, turn on the lightsaber using

the power switch under its base.

If not set to maximum,

set to maximum to insure best

gaming experience. Swipe left

to get to the next screen.

7 8

4. CONNECT

THE LIGHTSABER

Tap search for lightsaber. You have

10 seconds to click any lightsaber

button. The lightsaber tip turns

blue, which means it is connected.

Swipe left to get to the next

screen.

5. CALIBRATE

YOUR SABER

• While standing in your play area,

tab the calibration button

• Tab the calibration button

• Hold your lightsaber parallel to

the ﬂoor

• And follow the instructions to

make a ﬁgure-eight motion

until the circle gets ﬁlled in and

the saber vibrates in your hand.

• Swipe left to get to the next

screen.

On Android, if this fails it is

because location is not enabled.

Enable location in the settings of

your Android phone.

TIPS

9 10

6. PLACE YOUR TRACKING BEACON ON THE FLOOR

• Insert the included AA batteries inside the Tracking beacon.

• Turn on the beacon to pink.

• Place it on the ﬂoor in your play area.

• Make sure you will be able to stand 1.2 to 1.5m / 4 - 4.5 feet

away from the beacon while playing.

• Swipe left to get to the next screen.

7. CONNECT YOUR CABLE

• Remove your phone protective case if you have one.

• Make sure to connect the cable as on the pictures, so the

cable extends upwards.

• Swipe left to get to the next screen.

Do not force to insert the cable in your phone. 3 cables are

provided in the box, make sure to use the one matching your

phone connector.

TIPS

11 12

8. ACCEPT DISPLAY PERMISSIONS (ON ANDROID ONLY)

• Connect your phone to the headset to activate permissions

and grant them.

• Accept the pop up that appears. Disconnect the cable from

the headset when done, and Click the cross on top right

corner to continue to the next step.

9. TAKE THE PHONE TRAY OUT FROM THE HEADSET

• Pull out the tray from the inside of the headset

• Pull it out completely so you are able to insert the phone

13 14

10. INSERT THE PHONE IN THE CASE

• Make sure the stopper is in the position indicated on the screen

instructions. The position of the stopper depends on the phone

model you are using.

• Tap “continue” before inserting the phone inside the tray

• When you see the dash-box on screen, place the phone inside

the tray, face down, and close the tray.

• Fasten the phone by pushing the fasteners to max position.

CLICK LAUNCH ON THE SCREEN BEFORE INSERTING

THE PHONE IN THE HEADSET

make sure to place the stopper as indicated on the app, as the stopper

position depends on your phone model.

TIPS

15 16

11. INSERT THE TRAY

INSIDE THE HEADSET,

Slide in the tray, screen down all the way

inside until it clicks in position

12. AND CONNECT THE PHONE

TO THE HEADSET

Connect the micro-USB to its

port, the light will glow red

13. PUT ON THE HEADSET

AND START YOUR JEDI TRAINING.

MAY THE FORCE BE WITH YOU!

17 18

A. Control button

Use powers

B. Activation Matrix

Validate + Ignite

C. Power Switch

Learn the

Controls

of Your

Gear

A. Select Button

Validate

B. Back/Cancel

Button

C. Menu Button

Access to settings

Lenovo Star Wars Setup Manual

Lenovo Star Wars Setup Manual

Lenovo Star Wars Setup Manual

Related papers

Other documents