A.O. Smith Hot Water Storage Tanks Technical Documents

A.O. Smith
Brand
A.O. Smith
Model
Hot Water Storage Tanks
Type
Technical Documents
A. O. Smith storage tanks are ideal for
use with gas-fired copper heat exchanger
equipment for storage of any potable
water at temperatures up to 180°F.
GLASS LINED TANK - Alkaline
borosilicate composition permanently
fused to steel by firing at a temperature
of 1600°F, providing years of corrosion
protection and dependable use.
HEAVY GAUGE STEEL JACKET - With
baked enamel finish.
THREADED OPENINGS - All tanks
furnished with threaded openings for
thermometer, relief valve, 2” recirculation
lines, tankstat, and drain valve.
INSULATION - Storage Tanks meet or
exceed R12.5 minimum thermal insulation
requirements of the U. S. Department
of Energy and current edition of
ASHRAE/IESNA 90.1
TJ-80S, TJ-80A, TJV-120M and TJV-120A
•Fitsthrough30”door
•Magnesiumanodeforanti-corrosion
protection
TJ-80A
• 80gallons
• Highdensityfoaminsulationsaves
energy, helps reduce standby heat loss
• 160psiASMEstandardworkingpressure
TJV-120A
•119gallons
•Highdensityfoaminsulationsaves
energy, helps reduce standby heat loss
•160psiASMEstandardworkingpressure
TJ-80S
•80gallons
• Highdensityfoaminsulationsaves
energy, helps reduce standby heat loss
• 160psiworkingpressure
TJV-120M
• 119gallons
• Highdensityfoaminsulationsaves
energy, helps reduce standby heat loss
• 160psiworkingpressure
TJV-200-M - 175 GALLONS
• 160psiASMEstandardworkingpressure
• 2”foaminsulation
• Handholecleanout(Standard)
• Fitsthrough33”door
• Storageisdownsizedto175gallonsfor
a32”x77”envelopeforspacerestrictive
installations.ModelTJV-200isavailable
with 200 gallons of storage.
• Magnesiumanodesforextracorrosion
protection
5 YEAR WARRANTY
If the tank should leak any time during
the first 5 years, under the terms of the
warranty, A. O. Smith will repair or replace
the tank. Installation, labor, handling
and local delivery are extra. For complete
information, consult the written warranty.
Page 1 of 2
RevisedNovember2013
AOSTT35100
Commercial Storage Tanks
FACTORY JACKETED AND
INSULATED STORAGE TANKS
These A. O. Smith storage tanks are designed for storing potable water.
Fitting locations are designed to meet the needs of normal installations plus
those for the A. O. Smith Cer-Temp 80
®
piping methods.
FEATURES
MODELS
TJ-80S, TJ-80A
TJV-120A, TJV-120M
& TJV-200M
120 Gallon Model
(FOR SELECT MODELS)
SUGGESTED SPECIFICATION
Storage tank shall be A. O. SMITH glasslined storage tank. Tank shall be ________ “ x ________ “ and have a nominal capacity of _________ gallons. Tank(s)
shall have threaded openings as shown on drawings. Interior of tank(s) shall be glasslined with an alkaline borosilicate composition which has been fused to the
steel by ring at a temperature of 1600°F. Glass coating shall be continuous over the entire inner surface of the tank. Outer jacket shall have a baked enamel
nish. Meets minimum thermal insulation requirements of the U.S. Department of Energy and current edition of ASHRAE/IESNA 90.1. Cathodic protection shall
be provided. Tank shall have a working pressure of _________ psi. Tank shall have a ve year limited warranty as outlined in the written warranty.
AOSTT35100 R Nov 2013 Storage Tank Spec.indd 1 11/18/13 1:43 PM
For Technical Information and Automated Fax Service, call 800-527-1953. A.O. Smith Corporation reserves the right to make product changes or improvements without prior notice.
Commercial Storage Tanks
RevisedNovember2013
Page 2 of 2
www.hotwater.com
AOSTT35100
77 "
12 1/4"
17 1/4"
32 "
12 1/4"
17 1/4"
64"
1" NPT
ASME RATING PLATE AND
HAND HOLE LOCATED
UNDER COVER
2" NPT
3/4" NPT
3/4" NPT
(ANODES)
2" NPT
TJV-200M
4 1/ 8"
11"
42 1/4"
62"
3 1/2"
15"
54 1/4"
1" NPT
FRONT
2" NPT
FRONT
2" NPT
FRONT
CLEANOUT
2" NPT
FRONT & REAR
3/4" NPT
FRONT
2" NPT
3/4" NPT
(ANODE)
29 3/8"
TJV-120M
10 3/4"
17 3/4"
44 1/2"
61 3/4"
28"
9 3/4"
21 1/4"
50 1/2"
2" NPT FRONT
2" NPT FRONT
& REAR
3/4" NPT
1" NPT
ASME PLATE
LOCATED UNDER
COVER
1" NPT
1-1/4" NPT
(ANODE)
2" NPT
TJV-120A
2" ASME INSPECTION
OPENING (PLUGGED)
2" ASME INSPECTION
OPENING (PLUGGED)
2" ASME INSPECTION
OPENING (PLUGGED)
11"
19 1/2"
32 1/4"
42 3/4"
54 7/8"
26 1/2"
9 3/4"
2" NPT
FRONT & REAR
3/4" NPT
REAR
ASME PLATE
UNDER COVER
3/4" NPT
FRONT
2" NPT
FRONT & REAR
3/4" NPT
REAR
3/4" NPT
(ANODE)
2" NPT
1" NPT
TJ-80A
7"
16"
47"
51 7/8"
63"
25 1/4"
3 3/4"
2" NPT
FRONT & REAR
3/4" NPT
REAR
3/4" NPT
FRONT
2" NPT
FRONT & REAR
3/4" NPT
REAR
2" NPT
3/4" NPT
(ANODE)
TJ-80S
2" ASME INSPECTION
OPENING (PLUGGED)
2" ASME INSPECTION
OPENING (PLUGGED)
77 "
12 1/4"
17 1/4"
32 "
12 1/4"
17 1/4"
64"
1" NPT
ASME RATING PLATE AND
HAND HOLE LOCATED
UNDER COVER
2" NPT
3/4" NPT
3/4" NPT
(ANODES)
2" NPT
TJV-200M
4 1/ 8"
11"
42 1/4"
62"
3 1/2"
15"
54 1/4"
1" NPT
FRONT
2" NPT
FRONT
2" NPT
FRONT
CLEANOUT
2" NPT
FRONT & REAR
3/4" NPT
FRONT
2" NPT
3/4" NPT
(ANODE)
29 3/8"
TJV-120M
10 3/4"
17 3/4"
44 1/2"
61 3/4"
28"
9 3/4"
21 1/4"
50 1/2"
2" NPT FRONT
2" NPT FRONT
& REAR
3/4" NPT
1" NPT
ASME PLATE
LOCATED UNDER
COVER
1" NPT
1-1/4" NPT
(ANODE)
2" NPT
TJV-120A
2" ASME INSPECTION
OPENING (PLUGGED)
2" ASME INSPECTION
OPENING (PLUGGED)
2" ASME INSPECTION
OPENING (PLUGGED)
77 "
12 1/4"
17 1/4"
32 "
12 1/4"
17 1/4"
64"
1" NPT
ASME RATING PLATE AND
HAND HOLE LOCATED
UNDER COVER
2" NPT
3/4" NPT
3/4" NPT
(ANODES)
2" NPT
TJV-200M
4 1/ 8"
11"
42 1/4"
62"
3 1/2"
15"
54 1/4"
1" NPT
FRONT
2" NPT
FRONT
2" NPT
FRONT
CLEANOUT
2" NPT
FRONT & REAR
3/4" NPT
FRONT
2" NPT
3/4" NPT
(ANODE)
29 3/8"
TJV-120M
10 3/4"
17 3/4"
44 1/2"
61 3/4"
28"
9 3/4"
21 1/4"
50 1/2"
2" NPT FRONT
2" NPT FRONT
& REAR
3/4" NPT
1" NPT
ASME PLATE
LOCATED UNDER
COVER
1" NPT
1-1/4" NPT
(ANODE)
2" NPT
TJV-120A
2" ASME INSPECTION
OPENING (PLUGGED)
2" ASME INSPECTION
OPENING (PLUGGED)
2" ASME INSPECTION
OPENING (PLUGGED)
11"
19 1/2"
32 1/4"
42 3/4"
54 7/8"
26 1/2"
9 3/4"
2" NPT
FRONT & REAR
3/4" NPT
REAR
ASME PLATE
UNDER COVER
3/4" NPT
FRONT
2" NPT
FRONT & REAR
3/4" NPT
REAR
3/4" NPT
(ANODE)
2" NPT
1" NPT
TJ-80A
7"
16"
47"
51 7/8"
63"
25 1/4"
3 3/4"
2" NPT
FRONT & REAR
3/4" NPT
REAR
3/4" NPT
FRONT
2" NPT
FRONT & REAR
3/4" NPT
REAR
2" NPT
3/4" NPT
(ANODE)
TJ-80S
2" ASME INSPECTION
OPENING (PLUGGED)
2" ASME INSPECTION
OPENING (PLUGGED)
AOSTT35100 R Nov 2013 Storage Tank Spec.indd 2 11/18/13 1:43 PM
  • Page 1 1
  • Page 2 2

A.O. Smith Hot Water Storage Tanks Technical Documents

A.O. Smith
Brand
A.O. Smith
Model
Hot Water Storage Tanks
Type
Technical Documents
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents