Lopi Answer NexGen-Fyre™ Wood Insert User manual

Brand: Lopi

Model: Answer NexGen-Fyre™ Wood Insert

Type: User manual

This manual is also suitable for

1250i Wood Insert

Lopi Answer NexGen-Fyre™ Wood Insert: Experience the warmth and ambiance of a traditional wood-burning fireplace with the convenience and efficiency of modern technology. This innovative insert seamlessly blends classic design with advanced features, transforming your hearth into a captivating focal point.



Lopi Front Blower

Installation Instructions



Page 1 of 2 17601771.docx — 11/15/12 © Travis Industries, Inc.

Compatibility

SKU99000123–Answer,Revere,1750Insert,1250Insert

SKU99000126–Freedom

Items Required

 3/8”Nutdriver

 PhillipsScrewdriver

 SlipJointPliers(ifswitchingpowercordtoleftside)



To Switch the Power Cord to the Left Side:

Useapairofslip‐jointplierstodisconnectthestrainreliefwhichholdsthepowercordinplace.Withthe

powercordslackened,theMolexconnectorsthatattachthepowercordtotheblowerassemblymaybe

disconnected.Prythebuttonplugfromtheleftsideoftheblowerassembly

andinsertitintothehole

ontherightside.PulltheleftsideMolexconnectoroutfrombehindthedeflectionpla teandcutthe

nylontiethatholdsthewireback.InserttheMolexconnectoronthepowercordthroughtheholeon

theleftsideoftheblower

assemblyandattachittotheleftsideMolexconnecto r.Routethewire

directlybehindtheblowercage.Placethestrainreliefoverthepo wercord(itshouldbeinthesame

locationonthepowercordasbefore–approximately2”fromwherethewiressplit).Insertthestrain

relief

intotheholeontheleftsideuntilthestrainrelieflocksinplace.Makesurethepowercord,wires,

orMolexassemblydonotprotrudeintothebloweropening.







Lopi Front Blower

Installation Instructions



Page 2 of 2 17601771.docx — 11/15/12 © Travis Industries, Inc.

Installation

1. Attachtheblowerfollowingtheinstructionsbelow.

NOTE:Beforetighteningthescrewswitha3/8”nutdriver,lift theblowerupsoittucks

underneaththeashlip.



2. Plugthepowercordrunningfromthecontrolboxintoagrounded110‐voltelectricaloutlet.

Blower Operation

Theblowerwillnotstartuntiltheapplianceisuptotemperature,activatingathermodiskwhichthen

allowspowertothemotors.Onceuptotemperature,theblowerwilloperateatthespeeddetermined

bythepositionoftheblowerknob(seetheillustrationbelow).Theblowerwillshutoffautomatically



oncetheappliancecools.



Use a 3/8" nutdriver to secure the

front blower to the appliance.

Plug the

blower into a

110 volt

grounded

outlet.

3/8" Nutdriver

Remove the two screws.

Phillips

Screwdriver

Remove the rheostat plate to access the

blower mounting holes (leave the wiring

intact). Re-attach the rheostat plate after the

blower is attached.

OFF

Turn the dial all the

way counter-clockwise

until it clicks off.

HIGH

The high position is all the

way counter-clockwise,

without clicking off.

LOW

Turn the dial all

the way

clockwise.

Lopi Answer NexGen-Fyre™ Wood Insert User manual

Brand: Lopi

Model: Answer NexGen-Fyre™ Wood Insert

Type: User manual

This manual is also suitable for

1250i Wood Insert

Download PDF

report

Lopi Answer NexGen-Fyre™ Wood Insert User manual

This manual is also suitable for

Lopi Answer NexGen-Fyre™ Wood Insert User manual

Related papers

Other documents