DVS 99000153 User manual

Brand: DVS

Model: 99000153

Type: User manual

DVS 99000153 is a gas blower compatible with Lopi Berkshire, Tree of Life, Avalon Prairie, Avalon Cedar, and Lopi Allegiance (2001 model) stoves. It features a wiring harness, thermodisk, stud plate, rubber grommets, rheostat, and knob for easy installation. The blower helps circulate warm air throughout the room, improving heat distribution and overall comfort. It also includes a rheostat for adjustable fan speed, allowing you to customize the airflow to your desired level. Additionally, the blower's design positions it away from the impeller and burner to prevent damage to wires.

Blower, DVS Gas (Berkshire, Tree of Life, Prairie, Cedar, 2001 Allegiance) Part # 99000153

Page 1 of 4 4070219

CHECK CONDITION OF SHIPMENT

Upon receipt of this kit, check the condition of the packaging. Damage to the package should be noted on the carrier's freight

receipt. Any damage claims as a result of shipping must be handled through the shipper. Travis Industries will provide assistance

in resolving shipping claims or replacing items not included in the package. Please report any missing items immediately.

COMPATIBILITY

• Lopi Berkshire • Tree of Life • Avalon Prairie • Avalon Cedar • Lopi Allegiance (2001 model)

ITEMS NEEDED FOR ASSEMBLY

• 11/32” Socket Wrench • 1/4” Nutdriver • 1/2” Open End Wrench

PACKING LIST

• Blower Assembly • Wiring Harness • Thermodisk • Two Rubber Grommets (with spacers)

• Two Nuts and Washers • Stud Plate • Rheostat (with attachment nut & lock washer) • Rheostat Knob

INSTALLATION INSTRUCTIONS

WARNING: Turn the gas control valve to off and make sure the appliance has fully cooled prior to

conducting service.

1 Attach the two black wires on the included wiring harness to the thermodisk (orientation does not matter). Then slide

the thermodisk into the holder underneath the burner pan at the right rear of the stove.

All Models

Except the

Tree of Life and

2007 Berkshire

Snap Disk Bracket

(attached to stove)

Snap Disk

Snap Disk Wires on Wiring Harness

(Black - orientation does not matter)

Back of

Stove

Tree of Life

and

2007 Berkshire

Snap Disk Wires

(Black - orientation

does not matter)

Back of Stove

Remove the snap disk cover plate below

the burner on the

left side (when facing

the stove from the front).

Attach the snap disk

using the screws

removed in step "a".

Attach the wires

labeled snap disk to

the snap disk.

Blower, DVS Gas (Berkshire, Tree of Life, Prairie, Cedar, 2001 Allegiance) Part # 99000153

Page 2 of 4 4070219

2 Place the blower near the rear of the stove. Attach the wiring in grommets following the directions below.

Slide the rubber grommets (with

spacers inserted inside) onto the

fan mounting bracket.

Attach the black and white wires

labeled “Blower” to the blower

(orientation does not matter).

Attach the molex connector.

DO NOT PLUG THE STOVE

IN UNTIL INSTALLATION IS

COMPLETE.

Back of

Stove

1/4" Nutdriver

Remove one of the screws holding

the mounting bracket in place. Insert

the screw through the eyelet on the

green ground wire and replace.

Attach the two wires leading

from the control box to the two

block wires labeled “Rheostat”.

Route the wires labeled “Valve

on/off” and “Solenoid” under

the burner pan to a location

near the gas control valve.

Blower, DVS Gas (Berkshire, Tree of Life, Prairie, Cedar, 2001 Allegiance) Part # 99000153

Page 3 of 4 4070219

3 Slide the left side of the blower mounting bracket over the grommets on the left mounting bracket attached to the

stove (see the illustration below). Then insert the stud plate through the right side grommets and through the right

mounting bracket on the stove. Secure the stud plate with the included washers and nuts

Nut

Stud Plate

Washer

11/32”

Socket

Make sure the bracket

slides into the groove on

the rubber grommets.

Left Mounting

Bracket (on stove)

Rubber

Grommet

Blower Mounting

Bracket

Right Mounting

Bracket (on stove)

Back of

Stove

Blower Mounting Bracket

Stud Plate

Blower Mounting Bracket

4 Make sure all of the wiring is placed away from the blower impeller and the bottom of the burner. Use lock ties, if

necessary, to ensure no wires are damaged.

Blower, DVS Gas (Berkshire, Tree of Life, Prairie, Cedar, 2001 Allegiance) Part # 99000153

Page 4 of 4 4070219

5 Open the control cover following the directions below. Remove the button plug and install the rheostat.

Back of

Stove

Loosen the two screws holding the control

box in place. This allows access to the

back of the control box.

Attach the rheostat wires to the two

quick connects inside the control

box (orientation does not matter).

Control Box

Rheostat

1/2"

Wrench

NOTE: this tab fits into the

hole on the mounting bracket.

Attach the rheostat to

the control panel with

the included nut and

star washer.

Attach

the knob.

NOTE: make sure the

fiberglass heat shield is in

place when re-attaching the

control box (all models except

the cedar).

Phillips

Screwdriver

6 If using the modulating remote thermostat, attach the red and brown wires to the gas control valve.

Attach the red and

brown wires to the top

and bottom terminals

on the gas control

VALVE

“ON/OFF”

7 Plug the blower in. Let the heater achieve operating temperature and test blower operation.

DVS 99000153 User manual

DVS 99000153 User manual

Other documents