ESAB LKA 180 is a compact welding power source designed for welding with solid wire with shielding gas and tube electrode without gas. It features two control knobs for adjusting voltage and wire feed speed, a spot welding function for simple lap joints, and a thermal cut-out to prevent overheating. This versatile machine is suitable for various applications, including unalloyed, stainless, aluminum, and tube wire welding.
ESAB LKA 180 is a compact welding power source designed for welding with solid wire with shielding gas and tube electrode without gas. It features two control knobs for adjusting voltage and wire feed speed, a spot welding function for simple lap joints, and a thermal cut-out to prevent overheating. This versatile machine is suitable for various applications, including unalloyed, stainless, aluminum, and tube wire welding.
clk a1p00
Valid for serial no. 618--xxx--xxxx0456 180 001 020211
LKA 180
LKA 240
112101103105107109111102021110025108024042106023061104022041100020040060001
Bruksanvisning
Brugsanvisning
Bruksanvisning
Käyttöohjeet
Instruction manual
Betriebsanweisung
Manuel d’instructions
Gebruiksaanwijzing
Instrucciones de uso
Istruzioni per l’uso
Manual de instruções
Ïäçãßåò ÷ñÞóåùò
Instrukcja obs³ugi
Návod k pou¾ívání
Kezelési utasítások
Íþletme Elkitabý
-- 2 --
Rätt till ändring av specifikationer utan avisering förbehålles.
Ret til ændring af specifikationer uden varsel forbeholdes.
Rett til å endre spesifikasjoner uten varsel forbeholdes.
Oikeudet muutoksiin pidätetään.
Rights reserved to alter specifications without notice.
Änderungen vorbehalten.
Sous réserve de modifications sans avis préalable.
Recht op wijzigingen zonder voorafgaande mededeling voorbehouden.
Reservado el derecho de cambiar las especificaciones sin previo aviso.
Ci riserviamo il diritto di variare le specifiche senza preavviso.
Reservamo--nos o direito de alterar as especificações sem aviso prévio.
Äéáôçñåßôáé ôï äéêáßùìá ôñïðïðïßçóçò ðñïäéáãñáöþí ×ùñßò ðñïåéäïðïßçóç.
Zastrzegamy sobie prawo do wprowadzenia zmian.
Výrobce si vyhrazuje právo na zmìnu údajû bez pøedcházejiciho upozomìni.
Fenntartjuk az elözetes bejelentés nélküli változtatás jogát.
Donaným özellikleríní herhangí bír íhbarda bulundurmadan deÝíþtírme hakki saklidir.
SVENSKA 3..............................................
DANSK 10................................................
NORSK 17................................................
SUOMI 24................................................
ENGLISH 31..............................................
DEUTSCH 38.............................................
FRANÇAIS 45.............................................
NEDERLANDS 52.........................................
ESPAÑOL 59..............................................
ITALIANO 66..............................................
PORTUGUÊS 73..........................................
ÅËËÇÍÉÊÁ 80.............................................
POLSKI 88.................................................
ÈESKY 95.................................................
MAGYAR 102................................................
TÜRKÇE 109................................................
ENGLISH
-- 3 1 --
TOCe
1 DIRECTIVE 32........................................................
2SAFETY 32...........................................................
3 INTRODUCTION 33...................................................
4 TECHNICAL DATA 33.................................................
5 INSTALLATION 34....................................................
5.1 Electrical connection 35.......................................................
5.2 Wire 35.....................................................................
6 OPERATION 36.......................................................
6.1 Spot welding 37..............................................................
7 MAINTENANCE 37....................................................
8 ORDERING OF SPARE PARTS 37......................................
SELECTION TABLE 116...................................................
DIAGRAM 119............................................................
SPARE PARTS LIST 125...................................................
-- 3 2 --
bc05d18e
1 DIRECTIVE
DECLARATION OF CONFORMITY
Esab Welding Equipment AB, 695 81 Laxå, Sweden, gives its unreserved guarantee
that welding power source LKA 180 / 240 from serial number 618 complies with
standard EN 60974--1, in accordance with the requirements of directive (73/23/EEA)
and addendum (93/68/EEA).
-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --------
Paul Karlsson
Managing Director
Esab Welding Equipment AB
695 81 LAXÅ
SWEDEN Tel: + 46 584 81000 Fax: + 46 584 12336
Laxå 96--04--20
2SAFETY
WARNING
READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE INSTALLING OR OPERATING.
ARC WELDING AND CUTTING CAN BE INJURIOUS TO YOURSELF AND OTHERS. TAKE PRECAU -
TIONS WHEN WELDING. ASK FOR YOUR EMPLOYER’S SAFETY PRACTICES WHICH SHOULD BE
BASED ON MANUFACTURERS’ HAZARD DATA.
ELECTRIC SHOCK -- Can kill
S Install and earth the welding unit in accordance with applicable standards.
S Do not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.
S Insulate yourself from earth and the workpiece.
S Ensure your working stance is safe.
FUMES AND GASES -- Can be dangerous to health
S Keep your head out of the fumes.
S Use ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone
and the general area.
ARC RAYS -- Can injure eyes and burn skin.
S Protect your eyes and body. Use the c orrect welding screen and filter lens and wear protective
clothing.
S Protect bystanders with suitable screens or curtains.
FIRE HAZARD
S Sparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.
NOISE -- Excessive noise can damage hearing
S Protect your ears. Use earmuffs or other hearing protection.
S Warn bystanders of the risk.
MALFUNCTION -- Call for expert assistance in the event of malfunction.
PROTECT YOURSELF AND OTHERS!
GB
-- 3 3 --
bc05d18e
3 INTRODUCTION
LKA 180/240 is a compact, step--switched Welding power sources, intended for
welding with solid wire with shielding gas and tube electrode without gas.
The complete package comprises a power source with integral wire feed unit,
(PSF 160 welding torch), mains lead, return cable with clamp, feed rollers for 0.6
and 0.8 m m wire and a gas hose. The assembly kit includes a handle, rear axle, 2
rear wheels and 2 castors.
Two control knobs provide adjustment of voltage and wire feed speed, which are
easily selected by referring to the table on page 116.
You can switch between solid wire with shielding gas and tube electrode without gas
by simply switching + and -- connections on the terminal above the wire feed unit.
The spot welding function simplifies the task of making lap joints in sheet metal. A
thermal cut--out prevents the power source from overheating. T he cut--out is reset
atomatically when the power source has cooled.
4 TECHNICAL DATA
LKA 180 LKA 240 LKA 180 1--phase
Mains supply 230/400 V,
3--phase 50 Hz
230/400 V,
3--phase 50 Hz
230 V, 1--phase
50 Hz
Mains lead 4x2,5 mm@ 4x2,5 mm@ 3x2,5 mm@
Fuse, slow 10 A 16 A 16 A
Maximum load
10%
165 A 160 A
20% 200 A
60% 65 A 120 A 75 A
100% 60 A 85 A 60 A
Mains supply 400 V, 3--phase 50 Hz 400 V,3--phase 50 Hz
Mains lead 4x1,5 mm@ 4x1,5 mm@
Fuse, slow 10 A 10 A
Maximum load
11%
170 A
18% 200 A
60% 75 A 110 A
100% 60 A 85 A
Voltage steps 7 10 7
Open circuit voltage 15--33 V 18--36 V 16--33 V
Wire feed speed 1-- 15 m/min 1-- 15 m/min 1--15 m/min
Spot welding time 250 ms--2,5 s 250 ms--2,5 s 250 ms--2,5 s
Wire reel 5-- 15 kg 5-- 15 kg 5-- 15 kg
GB
-- 3 4 --
bc05d18e
LKA 180 1--phaseLKA 240LKA 180
Wire sizes
Unalloyed 0,6--0,8 mm 0,6--0,8 mm 0,6--0,8 mm
Stainless 0,6--0,8 mm 0,6--0,8 mm 0,6--0,8 mm
Aluminium 1,0 mm 1,0 mm 1,0 mm
T ube wire 0,8--0,9 mm 0,8--0,9 mm 0,8--0,9 mm
Dimensions 780x430x530 780x430x530 780x430x530
Weight 47 kg 50 kg 47 kg
Enclosure class IP 21 IP 21 IP 21
Application class
These welding rectifier conform to the requirements of IEC 974--1.
Enclosure class
The IP code indicates the enclosure class, i.e. the degree of protection against penetration by solid
objects or water. Equipment marked IP 21 is intended for indoor use.
Application class
The symbol indicates that the power source is designed for use in areas with increased
electrical hazard.
5 INSTALLATION
The in stallatio n must be executed by a professional.
WARNING!
This product is intended for industrial use. In a domestic environment this product may cause radio
interference. It is the user’s responsibility to take adequate precautions.
GAS CONNECTION
Assembly of components Does not apply to tube electrode.
bc05d001
GB
-- 3 5 --
bc05d18e
The power supply should be lifted by means of its lifting
eye. The handle is only intended for pulling it along the
ground.
Lifting instructions
5.1 Electrical connection
bc05d002
When delivered these power sources are wired for operation from a 400 V, 50 Hz,
three phase AC supply. The mains plug must conform to international standards and
be wired by a qual ified electrician. Check the mains voltage and fuses on all three
phases before connecting the machine.
bc05d008
400 V
230 V
5.2 Wire
bc05d004
TUBE WIRE SOLID WIRE
When welding with tube wire the cables connected to the + and -- terminals above
the wire feed unit must be switched.
GB
b
c
0
5
d
0
0
5
-- 3 6 --
bc05d18e
NOTE!
If the rollers slip or wire feed is unsatisfactory in any other way it may be necessary
to adjust the tension. This can be done using the tensioning screw on the pressure
arm.
WARNING!
Rotating parts can cause injury, take great care.
6 OPERATION
General safety regulations for the handling of the equipment can be found on
page 32. Read through before you start using the equipment!
S Connect the return cable (E) to the work piece.
S When welding with solid wire, open the gas valve ( A)
and adjust the gas flow with the reduction valve (B).
The flow should be between 8--12 l/min.
S Switch on the power source using the knob (L).
The white indicator lamp ( K) should light up.
S Press the trigger (D) on the welding torch until wire
is fed out of the contact tip (F).
S Select suitable welding settings using the
woltage selector knob (L) and the wire feed
knod (H) as indicated by the table on page 116.
S Start welding and adjust the settings if necessary.
S Indication lamp (J) light up if the Power source
becomes to hot.
GB
-- 3 7 --
bc05d18e
6.1 Spot welding
Select the spot welding time (G) on the scale marked 1--10. Spot welding
time can be set anywhere between 0.2--2.5 sek.
To set the welding voltage and wire feed speed see the recommended
table on page 116.
Press the torch trigger. When the set welding time has elapsed welding
will stop automatically. There is no need to release the trigger.
A new welding cycle will start when you press the trigger again.
b
c
0
9
7 MAINTENANCE
Note:
All warranty undertakings given b y the supplier cease to apply if the customer
attempts to rectify any faults on the machine during the warranty period.
IMPORTANT
This welding equipment has been designed, tested and manufactured to give long,
trouble--free service.
Regular maintenance is essential for safe and reliable operation.
Removal of dust
Blow away dust that has gathered in the power source
using dry compressed air at low pressure.
Wire feed unit
Components that are subject to wear must be
regularly cleaned and replaced to ensure reliable
wire feed. Note that if the tension is too high it may
cause excessive wear on the pressure roller,
feed roller and wire liner.
Torch
Regularly blow the wire liner clean and clean the gas shroud
8 ORDERING OF SPARE PARTS
Spare parts are ordered through your nearest ESAB representative, see back cover.
When ordering spare parts, please state machine type and number as well as desig-
nation and spare part number as shown in the spare parts list.
This will simplify dispatch and ensure you get the right part.
GB
455 894--001
367 556--001
466 074--001
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
ESAB LKA 180 is a compact welding power source designed for welding with solid wire with shielding gas and tube electrode without gas. It features two control knobs for adjusting voltage and wire feed speed, a spot welding function for simple lap joints, and a thermal cut-out to prevent overheating. This versatile machine is suitable for various applications, including unalloyed, stainless, aluminum, and tube wire welding.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI