Eizo 630LT-GR User manual

Category
TVs & monitors
Type
User manual

This manual is also suitable for

Touch Panel
LCD Monitor integrated
Windows-based Terminal
This is the manual for the following software version.
*
Microsoft Windows CE:
4.10 Rev. 2.7.1 or later
*
Microsoft Terminal Server Client: Ver. 7.2.0 or later
*
ICA Client:
Ver. 7.23 or later
Please confirm the version of the software built in eClient, and refer to
the suited User's Manual (Refer to the User's Manual Version List on
next page).
For Microsoft Windows CE.NET
Version E
- For Administrator -
Users Manual Version List
A handling description changes with versions of the software built in eClient. Please
refer to below.
NOTE
The version of software built in eClient can be checked with a [System]-[ICA] tab of
[Terminal Properties].
OS: Microsoft Windows CE .NET
Software
Manual
Microsoft Windows CE
Microsoft
Windows
Terminal Server
ICA Client
Software
E
(This manual)
4.10 Rev.2.7.1 or later Version 7.2.0 or later Version 7.23 or later
D 4.10 Rev.2.6.0 or later Version 7.1.0 or later
Version 6.30
[Build1078B] or later
C 4.10 Rev.2.5.3 or later
Version 7.0.1
[Build0020] or later
Version 6.30
[Build1063B] or later
B 4.10 Rev.2.5.1 or later
Version 7.0.1
[Build0020] or later
Version 6.30
[Build1063B] or later
A 4.10 Rev.2.5.1 or later
Version 7.0.1
[Build0019] or later
Version 6.30
[Build1063] or later
NOTE OS: Microsoft Windows CE 2.12
Software
Manual
Microsoft Windows CE
Microsoft
Windows
Terminal Server
ICA Client
Software
D 2.12 Rev.1.62 or later Version 6.53 or later
Version 6.20
[Build992] or later
C 2.12 Rev.1.58 or later Version 6.51 or later
Version 6.20
[Build992] or later
B 2.12 Rev.1.50 or later Version 6.28 or later
Version 6.20
[Build992] or later
A 2.12 Rev.1.29 or later Version 6.28 or later
Version 6.00
[Build923] or later
SAFETY SYMBOLS
This manual uses the safety symbols below. They denote critical information. Please read them
carefully.
WARNING
Failure to abide b
y
the information in a WARNING ma
y
result in serious in
j
ur
y
and
can be life threatening.
CAUTION
Failure to abide by the information in a CAUTION may result in moderate injury
and/or property or product damage.
Indicates a prohibited action.
Indicates to ground for safety.
Copyright© 2003-2004 EIZO NANAO CORPORATION. All rights reserved. No part of this
manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any
means, electronic, mechanical, or otherwise, without the prior written permission of EIZO
NANAO CORPORATION.
EIZO NANAO CORPORATION is under no obligation to hold any submitted material or
information confidential unless prior arrangements are made pursuant to EIZO NANAO
CORPORATION's receipt of said information. Although every effort has been made to ensure
that this manual provides up-to-date information, please note that EIZO monitor specifications
are subject to change without notice.
ENERGY STAR is a U.S. registered mark.
Apple and Macintosh are registered trademarks of Apple Computer, Inc.
BSQUARE is a registered trademark of Microsoft Corporation.
DPMS is a trademark and VESA is a registered trademark of Video Electronics Standards
Association.
JEM-CE is a trademark of BSQUARE Corporation.
VGA is a registered trademark of International Business Machines Corporation.
Windows is a registered trademark of Microsoft Corporation.
ScreenManager and PowerManager are trademarks of EIZO NANAO CORPORATION.
FlexScan and EIZO are registered trademarks of EIZO NANAO CORPORATION.
As an ENERGY STAR
®
Partner, EIZO NANAO CORPORATION has determined
that this product meets the ENERGY STAR guidelines for energy efficiency.
3
TABLE OF CONTENTS
1. INTRODUCTION ..................................................................................... 5
1-1. General Description ......................................................................................5
1-2. Features ........................................................................................................5
1-3. Package Contents..........................................................................................6
1-4. Controls & Connectors ................................................................................7
2. CONNECTING THE eClient 630LT-GR/630LT-GR-N ............................. 9
2-1. Setting up the eClient 630LT-GR/630LT-GR-N ............................................9
2-2. Connecting the eClient 630LT-GR/630LT-GR-N ..........................................9
3. SETTING UP the eClient 630LT-GR/630LT-GR-N ............................... 11
4. ADDING & CHANGING A CONNETION NAME................................... 21
4-1. Adding a Connection Name........................................................................21
4-2. Setting an Autostart Connection.................................................................24
4-3. Modifying a Connection Name...................................................................24
5. LOGON & LOGOFF.............................................................................. 25
5-1. Logon to a WTS / Logoff from a WTS........................................................25
5-2. Opening/Closing a Local Web Browser.......................................................29
6. USING THE TERMINAL PROPERTIES ................................................ 31
6-1. General .......................................................................................................33
6-2. Local Resources (RDP protocol only) .........................................................34
6-3. Display........................................................................................................35
6-4. Experience (RDP protocol only) .................................................................37
6-5. Control Panel..............................................................................................38
6-6. ICA Settings (ICA Protocol only)................................................................47
6-7. Server..........................................................................................................48
6-8. Security .......................................................................................................49
6-9. System.........................................................................................................51
7. SOFTWARE UPDATING/INSTALLATION ............................................ 52
8. PRACTICAL SETUP ............................................................................. 56
8-1. 630LT-GR/630LT-GR-N settings ................................................................56
8-2. Short cut command by keyboard ................................................................60
9. TROUBLESHOOTING........................................................................... 61
10. CLEANING.......................................................................................... 63
11. SPECIFICATIONS............................................................................... 65
12. REFERENCE ...................................................................................... 67
12-1. Attaching an Arm Stand ...........................................................................67
INDEX ....................................................................................................... 68
4
TABLE OF CONTENTS
4
1. INTRODUCTION
Thank you very much for purchasing the EIZO eClient 630LT-GR/630LT-GR-N.
1-1. General Description
The eClient 630LT-GR/630LT-GR-N connects with a Windows Terminal Server*, which
installed Microsoft Windows NT Server 4.0 Terminal Server Edition or Windows 2000
Server/Advanced Server/Datacenter Server, and this product is used as a terminal using
them.
- * Windows Terminal Server expresses ‘WTS’ hereafter.
1-2. Features
Lower TCO (Total Cost of Ownership)
Saves Space and Power Consumption
Less Heat, Less Noise
Speakers equipped
Serial Port for Modem/PDA
Local Web Browser added as a default connection 630LT-GR/630LT-GR-N
PC card slot for modem card, LAN card, and wireless LAN card
Wake on LAN supported
A Touch Panel and a Stylus Provided
eClient 630LT-GR/630LT-GR-N
Windows Terminal Server (WTS)
Output data of
applications
Input data from
mouse/keyboard
/st
y
lus
· Operation of applications
· Storage of data
· Display data
· Operation by
mouse/keyboard/stylus
1. INTRODUCTION
5
1-3. Package Contents
Please make sure that all the items listed are in the package. Please contact your local
dealer for assistance if any of the listed items are missing or damaged.
eClient 630LT-GR/630LT-GR-N
Mouse (FDM-310)
Power Cord
Screw (M4 x 12 mm) x 4
User’s Manual (includes Limited Warranty)
2 Stickers of the Brightness Control Guide
Stylus
NOTE
A keyboard is not included. Please purchase it separately.
Please use the enclosed mouse. EIZO NANAO CORPORATION will not be held
responsible for accident or damage caused by the use of a mouse manufactured by
other companies.
Please retain the packing materials for future transference.
Brightness can be adjusted by using key combinations on the keyboard (see page
36). Key combinations for an adjustment are presented on the stickers. Please
apply them for your convenience.
6
1. INTRODUCTION
1-4. Controls & Connectors
Front
(4)
(3)
(2)
(1)
(1) Power button
(2) Power Indicator
Color 630LT-GR/630LT-GR-N status
Green
Operation
Screen saver mode
Yellow Power save mode
Off
Power off (Wake on LAN standby)
(3) Speakers
(4) Volume Control
NOTE
When turning off/on the unit, leave the unit off for a few seconds before turning it on
again.
1. INTRODUCTION
7
Rear
(14)
(15)
(17)
(16)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(13)
(12)
(5) Mouse Connector
(6) Keyboard Connector
(7) Serial Port (RS-232C)
(8) Parallel Connector
(9) Power Connector
(10) Ethernet Connector (10 Base-T, 100 Base-TX)
(11) Headphone Connector
(12) Microphone Connector
(13) USB Port (Downstream) x 2
(14) PC Card Slot
(15) Security Lock*
1
(16) Holes for Mounting an Arm Stand*
2
(17) Stand (Detachable)
*
1
This allows for connection of a security cable. This lock supports Kensington’s
MicroSaver security system. For further information, please consult:
Kensington Technology Group
2855 Campus Drive, San Mateo, CA 94403 USA
Tel: 800-650-4242, x3348
Intl: 650-572-2700 Fax: 650-572-9675
http://www.kensington.com
*
2
The LCD monitor can be used with an optional arm stand by removing the stand
(See p.67).
8
1. INTRODUCTION
2. CONNECTING THE eClient
630LT-GR/630LT-GR-N
This chapter explains how to connect the eClient 630LT-GR/630LT-GR-N to a WTS.
2-1. Setting up the eClient 630LT-GR/630LT-GR-N
Please observe the following cautions when connecting the 630LT-GR/630LT-GR-N.
WARNING
Place the eClient 630LT-GR/630LT-GR-N on a strong, stable
surface.
A unit placed on an inadequate surface may fall, resulting in injury
or equipment damage. If the unit falls, disconnect the power
immediately and have the unit checked by a qualified service
engineer before using it again. Using a unit after it has been
dropped may result in fire or electric shock.
OK
Set the unit in an appropriate location.
Not doing so may result in fire, electric shock, or equipment
damage.
*
Do not place outdoors.
*
Do not place in the transportation system (ship, aircraft, trains,
automobiles, etc.)
*
Do not place in a dusty or humid environment.
*
Do not place in a location where the steam comes directly on the
screen.
*
Do not place near heat generating devices or a humidifier.
2-2. Connecting the eClient 630LT-GR/630LT-GR-N
NOTE
Before connecting the eClient 630LT-GR/630LT-GR-N, confirm the following:
- The eClient 630LT-GR/630LT-GR-N is turned off.
- The WTS is turned on.
Connect the peripherals to the appropriate connectors of the unit.
2. CONNECTING THE eClient 630LT-GR/630LT-GR-N
9
1. In case of connecting the WTS through LAN:
Connect the eClient 630LT-GR/630LT-GR-N to the network with an
Ethernet cable.
In case of a dial-up or dial-in connection:
Connect the eClient 630LT-GR/630LT-GR-N to a modem or a
modem card.
NOTE
Please remove the lid on the side of the 630LT-GR/630LT-GR-N before
connecting a LAN card or a modem card.
2. Plug a keyboard and a mouse into the eClient 630LT-GR/630LT-GR-
N. If using other devices, please connect them to the appropriate
connectors.
In use of a stylus or a finger as an input device, it is not necessary to connect a
mouse.
3. If using other devices, please connect them to the appropriate
connectors.
4. Plug the power cord into the power connector.
WARNING
Use the enclosed power cord and connect to the standard
power outlet of your country.
Be sure to remain within the rated voltage of the power cord.
Not doing so may result in fire or electric shock.
The equipment must be connected to a grounded main
outlet.
Not doing so may result in fire or electric shock.
10
2. CONNECTING THE eClient 630LT-GR/630LT-GR-N
3. SETTING UP the eClient
630LT-GR/630LT-GR-N
This chapter presents how to prepare for a connection with a WTS when the eClient
630LT-GR/630LT-GR-N starts up for the first time.
1. Turn on the eClient 630LT-GR/630LT-GR-N.
The power indicator turns green and a picture appears on the screen.
NOTE
When no picture is displayed, or when the message (No keyboard connected. /
No mouse connected.) is shown on the screen, please refer to “8.
Troubleshooting” on page 61. (In use of a stylus or a finger as an input device,
“No Mouse Connected!!” caution does not effect our operation.)
2. “Touch panel calibration” is displayed.
Five targets are displayed on the screen. Press the targets with a stylus or a
fingertip to locate the center of the touch panel. If you accidentally touched the
screen in the wrong spot during calibration, you will distort the touch panel
calibration.
3. SETTING UP the eClient 630LT-GR/630LT-GR-N
11
3. “Calibration measured” window is displayed when you finished.
Click the “Enter” key to accept the settings.
4. “eClient Setup Wizard” is displayed.
(Set up the 630LT-GR/630LT-GR-N according to directions of the displayed dialog
box.)
12
3. SETTING UP the eClient 630LT-GR/630LT-GR-N
5. End User License Agreement page is displayed.
Read the content and click [Accept] to continue.
3. SETTING UP the eClient 630LT-GR/630LT-GR-N
13
6. Set up the network environment.
[Terminal Name] ................Type the name to identify this unit on the network.
Click [Network Properties] and set up connection information according to the
connection method to WTS/Web server.
Connection method Reference page
In case of connecting the WTS/Web through Built-in
LAN
p.15
In case of connecting with a NE2000 compatible LAN
card:
p.15
In case of connecting with a Cisco wireless LAN card/
Agere wireless LAN card:
p.16
In case of a dial-up connection:
p.17
In case of the dial-in connection (ICA protocol only) to
log on to WTS
Go to step 7
* Skip the [Network
Properties] settings
NOTE
[Dial-Up Connection] [Dial-In Connection]
Telephone
Lines
Telephone
Lines
RAS Server
WTS
eClient
WTS FTP Server eClient
14
3. SETTING UP the eClient 630LT-GR/630LT-GR-N
In case of connecting the WTS/Web through Built-in LAN:
(1) Double-click [Built-in LAN] icon.
[IP Address] ........................Type the IP address of the unit.
[Name Servers] ...................Type the IP address of each server when DNS or
WINS is used.
[Advanced]..........................Type the transmission speed and MAC Address of a
network.
In case of connecting with a NE2000 compatible LAN card:
(1) Double-click [NE 20001] icon.
[IP Address] ........................Type the IP address of the unit.
[Name Servers] ...................Type the IP address of each server when DNS or
WINS is used.
Example;
In case of connecting with a
NE2000 compatible LAN card
3. SETTING UP the eClient 630LT-GR/630LT-GR-N
15
In case of connecting with a Cisco wireless LAN card/Agere wireless LAN card:
(1) Double-click [CISCO1]/[WLAGS461] icon.
[IP Address] ........................Type the IP address of the unit.
[Name Servers]....................Type the IP address of each server when DNS or
WINS is used.
[Wireless Networks]
...................................Set the connection setting with a wireless LAN card.
NOTE
In case of selecting [Obtain an IP address via DHCP], deactivate the built-in
LAN by the procedure below.
(1) Double-click [Built-in LAN] icon
(2) Select [Specify an IP address] of [IP Address] tab, type “255.255.255.255” in
the [IP Address] box.
16
3. SETTING UP the eClient 630LT-GR/630LT-GR-N
In case of a dial-up connection:
(1) Double-click [Make New Connection] icon.
(2) Type a name for the connection and select the connection type (Dial-Up
Connection).
(3) Select a model, set up the TCP/IP settings and Security settings.
(4) Type the phone number for the connection.
(5) In case of a dial-up connection, the information of local location needs to be
set up. Set up the information in the later procedure 8.
NOTE
In using the following case, set up
in addition to the WTS/Web server
information settings
.
- When you use VPN (Virtual Private Network)
(1) Double-click [Make New Connection] icon.
(2) Type a name for the connection and select [Virtual Private Network].
(3) Type host name or IP address and set up the TCP/IP settings and Security
settings.
- When you use ADSL
(1) Double-click [Make New Connection] icon.
(2) Type a name for the connection and select [PPP over Ethernet [PPPoE].
(3) Type PPPoE service name (or blank for any service) and set up the TCP/IP
settings and Security settings.
Set up a Remote Connection
By setting up a Remote Connection, the WTS/Web server can be connected easily.
(1) Double-click [Make New Connection] icon.
(2) Type a name for the connection and select [Remote Connection Setup].
(3) Select the desired connection from the [Available Connections] list and click
[Add] button to set in the [Current Connections]. (Connections listed in the
[Current Connections] will be executed with the listed order.)
(4) Select the [Make default connection] check box.
A small window will be displayed on the right bottom of the screen.
Clicking an active button of the small window starts the connection listed in
the [Current Connections].
To set an automatically start connection when the eClient 630LT-GR/630LT-GR-N
boots up, select the [Connect automatically on boot up] check box.
3. SETTING UP the eClient 630LT-GR/630LT-GR-N
17
7. Set up the desktop area.
[Desktop Area and Refresh Frequency]
...................................Set the resolution/refresh rate. (630LT-GR/630LT-
GR-N supports 1024 x 768 @60 Hz only).
[Desktop Colors].................Set the desktop color (256 Colors / High color) of the
following.
- Windows CE desktop (before WTS connection)
- Windows desktop (after a WTS connection with RDP
protocol)
NOTE
[High Color] setting after WTS connection can be available only when
connecting with WTS, which version is 5.1 or later.
After WTS connection, the WTS setting may control the desktop color.
18
3. SETTING UP the eClient 630LT-GR/630LT-GR-N
8. Set up the browser connection.
Set up if you are setting up a web browser connection.
(1) Select [Internet Options] icon and click [Open].
[General].............................Set up the browser.
[Connection].......................Set up the connection method to the browser.
[Security].............................Set up the security for the connection to the browser.
[Advanced]..........................Set up the display method of the browser.
9. Set up the printer.
Set up if you are using a local printer.
NOTE
The following is required to install a local printer.
- A printer is connected to the serial connector, the parallel connector or a USB
port.
- An RDP protocol is used for connection to a WTS.
- Microsoft Windows 2000 Server / Advanced Server / Datacenter Server is
installed in a WTS.
(1) Select [Printer] icon and click [Open] icon.
(2) Select [Add printer] icon and click [Open] icon.
(3) “WTB Printer Wizard” is displayed (Follow the direction of the dialog box.).
1. Select a printer port.
(Select “COM 1” for connecting to the serial connector, “LPTx” for the
parallel connector or the USB port.)
2. Select a model of your printer.
3. Name your printer.
3. SETTING UP the eClient 630LT-GR/630LT-GR-N
19
10. Setup the Local sender’s setting
Setup if you are connecting to WTS/Web server by dial-up connection.
(1) Select [Dialing] icon and click [Open] icon.
[Location name]..................Choose the sender’s location (click [New] to add a
new sender’s location).
[Local Settings are:].............Setup the local settings.
11. The last page of the “eClient Setup Wizard” is displayed.
Click [Finish].
Click [Yes] if a “Terminal Settings change” dialog box is displayed.
The “Terminal Connection Manager” dialog box will be displayed after restarting.
NOTE
Click [No] to finish the “eClient Setup Wizard” and display “Terminal
Connection Manager” on the screen. The setting is not activated until the
630LT-GR/630LT-GR-N is restarted.
20
3. SETTING UP the eClient 630LT-GR/630LT-GR-N
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68

Eizo 630LT-GR User manual

Category
TVs & monitors
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI