Earthquake Sound 52 User manual
- Category
- Soundbar speakers
- Type
- User manual
This manual is also suitable for
ROCK-on Series
User Manual
Earthquake Sound Corp. | (510) 732-1000 | U.S. Toll Free: (800) 576-7944 | www.earthquakesound.com
Granite-52 Speakers
Granite-10D Subwoofer
Table of Contents
3
3
5
6
6
6
7
8
8
9
Introduction.............................................................................................
Safety Instructions..................................................................................
Unpacking Tips.......................................................................................
Applications............................................................................................
Features..................................................................................................
Wiring Your System................................................................................
Wiring Options........................................................................................
Design....................................................................................................
Specifications.........................................................................................
Warranty Information..............................................................................
Safety Instructions
Safety First
Symbols Explained:
Note: Calls attention to information that is essential to highlight.
This documentation contains general safety, installation, and operating instructions for the ROCK-
on series. It is important to read this user’s manual before attempting to use these products. Pay
particular attention to the safety instructions.
Appears on the component to indicate the presence of uninsulated,
dangerous voltage inside the enclosure – voltage that may be
sufficient to constitute a risk of shock.
Calls attention to a procedure, practice, condition or the like that, if
not correctly performed or adhered to, could result in injury or death.
Calls attention to a procedure, practice, condition or the like that, if not
correctly performed or adhered to, could result in damage to or
destruction of part or all of the product.
Rock speakers have become a necessity in the outdoor audio entertainment market. Having outdoor
speakers in your backyard that blend in introduces an audio element while remaining invisible. Rock
speakers transform your backyard and pool area into a party zone.
Earthquake Sound Corporation has designed and manufactured speakers for over 25 years. This
experience was put to the test when designing the ROCK-on line of outdoor rock speakers. In addition to
designing the product to produce accurate sound, it must blend into any environment while handling a variety
of hard weather conditions.
The Granite-52 speakers and Granite-10D subwoofer, part of the new ROCK-on outdoor speaker series, are
specifically designed to imitate a rock appearance and easily blend in with any outdoor environment. Made
with UV treated, weather-resistant enclosure materials and durable epoxy resin construction, the ROCK-on
speakers can withstand the demanding outdoor elements.
Granite-52 is a pair of rock speakers with a 5 1/4 inch woofer and a ½ inch tweeter. They serve as your left
and right speakers and have an amazing frequency response that is unmatched by any other rock speaker.
They produce a crisp, clean, and accurate audiophile sound.
The ROCK-on subwoofer, the Granite-10D, features high power crossovers that reduce distortions and
deliver pure sound that blends in with nature. The Granite-10D brings bass to your outdoor space, something
that is greatly needed in today’s rock speaker market. Granite-10D’s port is “S” shaped so water cannot get
trapped inside. We have tested and retested our ROCK-on speakers to ensure they are up to par with our
reputable line of subs. Combined with the Granite-52 speakers which have a matching finish, you can turn
any backyard into an entertainment center.
ROCK-on outdoor speakers are the ideal choice for listening to music in the garden, by the pool, in the yard,
or on the patio.
Introduction
ROCK-on Manual 3
ROCK-on Manual 2
Earthquake Sound Corp. | (800) 576-7944 | www.earthquakesound.com
Customer Support
Tel: 800-576-7944
Fax: 510-732-1095
The Sound That Will Move You
Earthquake Sound Corporation
2727 McCone Avenue
Hayward, CA 94545
Tel: 510-732-1000
Fax: 510-732-1095
© 2009 Earthquake Sound Corporation. All rights reserved.
This document should not be construed as a commitment on the part of Earthquake Sound Corporation. The
information is subject to change without notice. Earthquake Sound Corporation assumes no responsibility for
errors that may appear within this document.
S O U N D
Specifications are subject to change without notice.
Table of Contents
3
3
5
6
6
6
7
8
8
9
Introduction.............................................................................................
Safety Instructions..................................................................................
Unpacking Tips.......................................................................................
Applications............................................................................................
Features..................................................................................................
Wiring Your System................................................................................
Wiring Options........................................................................................
Design....................................................................................................
Specifications.........................................................................................
Warranty Information..............................................................................
Safety Instructions
Safety First
Symbols Explained:
Note: Calls attention to information that is essential to highlight.
This documentation contains general safety, installation, and operating instructions for the ROCK-
on series. It is important to read this user’s manual before attempting to use these products. Pay
particular attention to the safety instructions.
Appears on the component to indicate the presence of uninsulated,
dangerous voltage inside the enclosure – voltage that may be
sufficient to constitute a risk of shock.
Calls attention to a procedure, practice, condition or the like that, if
not correctly performed or adhered to, could result in injury or death.
Calls attention to a procedure, practice, condition or the like that, if not
correctly performed or adhered to, could result in damage to or
destruction of part or all of the product.
Rock speakers have become a necessity in the outdoor audio entertainment market. Having outdoor
speakers in your backyard that blend in introduces an audio element while remaining invisible. Rock
speakers transform your backyard and pool area into a party zone.
Earthquake Sound Corporation has designed and manufactured speakers for over 25 years. This
experience was put to the test when designing the ROCK-on line of outdoor rock speakers. In addition to
designing the product to produce accurate sound, it must blend into any environment while handling a variety
of hard weather conditions.
The Granite-52 speakers and Granite-10D subwoofer, part of the new ROCK-on outdoor speaker series, are
specifically designed to imitate a rock appearance and easily blend in with any outdoor environment. Made
with UV treated, weather-resistant enclosure materials and durable epoxy resin construction, the ROCK-on
speakers can withstand the demanding outdoor elements.
Granite-52 is a pair of rock speakers with a 5 1/4 inch woofer and a ½ inch tweeter. They serve as your left
and right speakers and have an amazing frequency response that is unmatched by any other rock speaker.
They produce a crisp, clean, and accurate audiophile sound.
The ROCK-on subwoofer, the Granite-10D, features high power crossovers that reduce distortions and
deliver pure sound that blends in with nature. The Granite-10D brings bass to your outdoor space, something
that is greatly needed in today’s rock speaker market. Granite-10D’s port is “S” shaped so water cannot get
trapped inside. We have tested and retested our ROCK-on speakers to ensure they are up to par with our
reputable line of subs. Combined with the Granite-52 speakers which have a matching finish, you can turn
any backyard into an entertainment center.
ROCK-on outdoor speakers are the ideal choice for listening to music in the garden, by the pool, in the yard,
or on the patio.
Introduction
ROCK-on Manual 3
ROCK-on Manual 2
Earthquake Sound Corp. | (800) 576-7944 | www.earthquakesound.com
Customer Support
Tel: 800-576-7944
Fax: 510-732-1095
The Sound That Will Move You
Earthquake Sound Corporation
2727 McCone Avenue
Hayward, CA 94545
Tel: 510-732-1000
Fax: 510-732-1095
© 2009 Earthquake Sound Corporation. All rights reserved.
This document should not be construed as a commitment on the part of Earthquake Sound Corporation. The
information is subject to change without notice. Earthquake Sound Corporation assumes no responsibility for
errors that may appear within this document.
S O U N D
Specifications are subject to change without notice.
Important Safety Instructions
1) Read these instructions in their entirety.
10) Protect the power cord from being walked on or pinched,
particularly at plugs, convenience receptacles, and the pint
2) Store this manual and packaging in a safe place.
where they exit from the apparatus.
3) Heed all warnings.
11) Only use attachments & accessories specified by the
manufacturer.
4) Follow instructions (do not take short cuts).
12) Use only compatible rack or cart for final resting position.
5) Do not use this apparatus near water.
13) Unplug this apparatus during lighting storm or when unused
6) Clean only with a dry cloth.
for long period of time.
7) Do not block any ventilation openings. Install in accordance
14) Refer all servicing to qualified service personal. Servicing is
with the manufacturers instructions.
required when the apparatus has been damaged in any way
such as; power-supply cord or plug is damaged, liquid has
8) Do not install near any heat sources such as radiators, heat
been spilled or objects have fallen into the apparatus, the
registers, stoves, or other apparatuses that produce heat.
apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
9) Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
15) To reduce the risk of fire or electric shock, do not expose
one wider that the other. A grounding-type plug has two
this apparatus to rain or moisture.
blades and a third grounding prong. The wide blade or the
third prong is provided for your safety. If the provided plug
does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
This triangle, which appears on your component,
alerts you to the presence of uninsulated,
dangerous voltage inside the enclosure -
voltage that may be sufficient to
constitute a risk of shock.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This triangle, which appears on your component,
alerts you to important operating and
maintenance instructions in this
accompanying literature.
ROCK-on Manual 4
ROCK-on Manual 5
Earthquake Sound Corp. | (800) 576-7944 | www.earthquakesound.com
• Keep all power cords away from all signal cables to prevent
humming from induced noise.
• Choose reliable signal cables cords (Earthquake Sound also
specializes in high-performance RCA cables and patches).
• All speaker wires that are ran through the walls should be twisted
type to reduce potential hum noise pick up.
• Label both ends of all wires with the corresponding room
location.
• It is best to use a grounded electrical outlet to power the
amplifier. Lack of input ground reference could be unsafe.
Consult with your electrical contractor about proper grounding.
Unpacking system components
There are several factors to consider before installing Earthquake
Sound’s .ROCK-on series
• What are the intended listening zones?
• What system options and accessories might be required for
features such as local sources, etc.?
• From where in each zone will the listener prefer to control the
system? Where will the remote gains be located? Where will the
speakers be located?
• Where will the source equipment be located?
System installation considerations
Connection tips
• Keep the original carton and packing materials for future
shipment or storage.
• Check for any visual signs of damage. If you encounter any
concealed damage, consult your Earthquake Sound dealer
before proceeding with unit installation.
• Retain the sales receipt as it established the duration of the
limited warranty and provided information for insurance
purposes.
Specifications are subject to change without notice.
Important Safety Instructions
1) Read these instructions in their entirety.
10) Protect the power cord from being walked on or pinched,
particularly at plugs, convenience receptacles, and the pint
2) Store this manual and packaging in a safe place.
where they exit from the apparatus.
3) Heed all warnings.
11) Only use attachments & accessories specified by the
manufacturer.
4) Follow instructions (do not take short cuts).
12) Use only compatible rack or cart for final resting position.
5) Do not use this apparatus near water.
13) Unplug this apparatus during lighting storm or when unused
6) Clean only with a dry cloth.
for long period of time.
7) Do not block any ventilation openings. Install in accordance
14) Refer all servicing to qualified service personal. Servicing is
with the manufacturers instructions.
required when the apparatus has been damaged in any way
such as; power-supply cord or plug is damaged, liquid has
8) Do not install near any heat sources such as radiators, heat
been spilled or objects have fallen into the apparatus, the
registers, stoves, or other apparatuses that produce heat.
apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
9) Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
15) To reduce the risk of fire or electric shock, do not expose
one wider that the other. A grounding-type plug has two
this apparatus to rain or moisture.
blades and a third grounding prong. The wide blade or the
third prong is provided for your safety. If the provided plug
does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
This triangle, which appears on your component,
alerts you to the presence of uninsulated,
dangerous voltage inside the enclosure -
voltage that may be sufficient to
constitute a risk of shock.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This triangle, which appears on your component,
alerts you to important operating and
maintenance instructions in this
accompanying literature.
ROCK-on Manual 4
ROCK-on Manual 5
Earthquake Sound Corp. | (800) 576-7944 | www.earthquakesound.com
• Keep all power cords away from all signal cables to prevent
humming from induced noise.
• Choose reliable signal cables cords (Earthquake Sound also
specializes in high-performance RCA cables and patches).
• All speaker wires that are ran through the walls should be twisted
type to reduce potential hum noise pick up.
• Label both ends of all wires with the corresponding room
location.
• It is best to use a grounded electrical outlet to power the
amplifier. Lack of input ground reference could be unsafe.
Consult with your electrical contractor about proper grounding.
Unpacking system components
There are several factors to consider before installing Earthquake
Sound’s .ROCK-on series
• What are the intended listening zones?
• What system options and accessories might be required for
features such as local sources, etc.?
• From where in each zone will the listener prefer to control the
system? Where will the remote gains be located? Where will the
speakers be located?
• Where will the source equipment be located?
System installation considerations
Connection tips
• Keep the original carton and packing materials for future
shipment or storage.
• Check for any visual signs of damage. If you encounter any
concealed damage, consult your Earthquake Sound dealer
before proceeding with unit installation.
• Retain the sales receipt as it established the duration of the
limited warranty and provided information for insurance
purposes.
Specifications are subject to change without notice.
•
• Rock-like appearance and finish to easily blend in with any outdoor environment
• Completely sealed speaker with Santoprene surrounds, poly cones and poly dust caps
• High power crossovers (for Granite 10D only).
UV treated and weather-resistant enclosure materials
• Epoxy resin durable construction
ROCK-on Manual 6
ROCK-on Manual 7
Earthquake Sound Corp. | (800) 576-7944 | www.earthquakesound.com Specifications are subject to change without notice.
Features
Wiring Your System
Applications
• Outdoor Home Theater
• Patio
• BBQ Area
• Pool
• Backyard and Frontyard
• Garden
• Balcony
1. Use direct burial wire and measure out how much you will need.
2. Dig a 6-inch deep trench to each speaker.
3. Connect the speaker wire to the speaker. It is recommended that you use heat-shrink tubing
to seal each individual conductor, then heat-shrink the two connections together.
Make sure that all connections are secure. A poor connection can lead to corrosion and a
damaged speaker.
4. Run the wire through the trench to the amplifier.
5. Connect the speaker wire to the terminals on the back of your amplifier.
Make sure that the speaker wires’ polarity is connected correctly.
+ (positive, red) to speaker red wire (positive)
– (negative, black) to speaker black wire (negative)
Note: If using the XJ-300FR Stereo Amplifier, wire as described on the adjacent page but bridge
the two positive (red) wires to the subwoofer. This uses the Stereo option and the Mono option
at the same time.
6. Turn your amplifier on and test the system with your favorite music. If the speakers are
operating properly, refill the trench.
Wiring Options
Subwoofer
SpeakerSpeaker
Earthquake Sound’s XJ-300FR Stereo amplifier can be used for your ROCK-on 2.1 system.
In tri-mode wiring, the user can connect the 2 channel stereo and the mono at the same time.
The subwoofer connection below demonstrates a series wiring formula which has a load
impedance of 8? .
To simplify the wiring process, use Earthquake Sound’s SWAT 2.4 Wireless Transceiver
1. Connect the rock speakers and subwoofer to the XJ-300FR amplifier as shown above.
2. Connect the SWAT 2.4 Receiver to the XJ-300FR amplifier through the RCA inputs.
3. Connect the SWAT 2.4 Transmitter to any music player that has a mini jack or RCA output.
Note: Make sure both the Transmitter and the Receiver are connected to a power source,
either through the DC power supply or the USB port.
L
L
+ +
+
+ +
++
–
–
––
––
–
R
R
XJ-300FR Stereo Amplifier
MONO
USB
INPUT
CH
Reset/Mute
Status
TRANSMITTER
RECEIVER
USB
OUTPUT
CH
Reset/Mute
Status
SWAT 2.4
•
• Rock-like appearance and finish to easily blend in with any outdoor environment
• Completely sealed speaker with Santoprene surrounds, poly cones and poly dust caps
• High power crossovers (for Granite 10D only).
UV treated and weather-resistant enclosure materials
• Epoxy resin durable construction
ROCK-on Manual 6
ROCK-on Manual 7
Earthquake Sound Corp. | (800) 576-7944 | www.earthquakesound.com Specifications are subject to change without notice.
Features
Wiring Your System
Applications
• Outdoor Home Theater
• Patio
• BBQ Area
• Pool
• Backyard and Frontyard
• Garden
• Balcony
1. Use direct burial wire and measure out how much you will need.
2. Dig a 6-inch deep trench to each speaker.
3. Connect the speaker wire to the speaker. It is recommended that you use heat-shrink tubing
to seal each individual conductor, then heat-shrink the two connections together.
Make sure that all connections are secure. A poor connection can lead to corrosion and a
damaged speaker.
4. Run the wire through the trench to the amplifier.
5. Connect the speaker wire to the terminals on the back of your amplifier.
Make sure that the speaker wires’ polarity is connected correctly.
+ (positive, red) to speaker red wire (positive)
– (negative, black) to speaker black wire (negative)
Note: If using the XJ-300FR Stereo Amplifier, wire as described on the adjacent page but bridge
the two positive (red) wires to the subwoofer. This uses the Stereo option and the Mono option
at the same time.
6. Turn your amplifier on and test the system with your favorite music. If the speakers are
operating properly, refill the trench.
Wiring Options
Subwoofer
SpeakerSpeaker
Earthquake Sound’s XJ-300FR Stereo amplifier can be used for your ROCK-on 2.1 system.
In tri-mode wiring, the user can connect the 2 channel stereo and the mono at the same time.
The subwoofer connection below demonstrates a series wiring formula which has a load
impedance of 8? .
To simplify the wiring process, use Earthquake Sound’s SWAT 2.4 Wireless Transceiver
1. Connect the rock speakers and subwoofer to the XJ-300FR amplifier as shown above.
2. Connect the SWAT 2.4 Receiver to the XJ-300FR amplifier through the RCA inputs.
3. Connect the SWAT 2.4 Transmitter to any music player that has a mini jack or RCA output.
Note: Make sure both the Transmitter and the Receiver are connected to a power source,
either through the DC power supply or the USB port.
L
L
+ +
+
+ +
++
–
–
––
––
–
R
R
XJ-300FR Stereo Amplifier
MONO
USB
INPUT
CH
Reset/Mute
Status
TRANSMITTER
RECEIVER
USB
OUTPUT
CH
Reset/Mute
Status
SWAT 2.4
Granite-10D Design
Granite-52 Design
Specifications
ROCK-on Manual 8
Earthquake Sound Corp. | (800) 576-7944 | www.earthquakesound.com
Frequency
Response (±3dB)
50Hz-21kHz
30Hz-100Hz
Recommended
Amplifier Power
40-200 Watts20-400 Watts
Nominal Impedance
Sensitivity(1W@1M)
93dB
92dB
Woofer
5 1/4”
(133mm)
10” (254mm)
Two 2.5” diameter voice coils
Tweeter
½” (13mm)
Mylar
N/A
Dimensions
(HxWxD)
8 1/2” (216mm)
8 1/2” (216mm)
9” (229mm)
14” (356mm)
18 1/2” (470mm)
21” (546mm)
Finish
Granite rockGranite rock
Enclosure
15mm epoxy resin
15mm epoxy resin
Granite-10D
Granite-52
• 10” long excursion dual coil driver
• 2.5” diameter voice coil with 1.5” winding height
Granite-10D is a dual voice coil long excursion subwoofer. It has a massive motor that is unconventional in the
outdoor rock speaker market. The voice coil has a whopping 2.5” diameter and 1.5” winding height. The
overall excursion is over 2” peak to peak. Due to its voice coil winding height, the Granite-10D produces more
sound pressure level, SPL, while using less current from your amplifier.
Conventional rock speakers are totally sealed and will heat up to a temperature that exceeds 180 degrees. So
as soon as you turn on the music, the rock speaker only gets hotter. Not the Granite-10D.
Granite-10D has a clever ported design that allows the subwoofer to release the hot air. This port is a tube that
has an opening in the lower back side but extends upward inside the box to prevent moisture and water from
being trapped inside. In addition to keeping the subwoofer cool, this port adds 3dB of bass. 3dB is equal to half
the volume.
Like the Granite-52, the Granite-10D also has a poly propylene injection molded cone with a butyl rubber
surround.
1 Year Limited Warranty Information
ROCK-on Manual 9
Specifications are subject to change without notice.
It Is Recommended That You Place Your Serial Number Here For Reference
ROCK-on Granite-52 and Granite-10D one (1) year limited warranty:
Earthquake warrants the original purchaser that the speaker or amplifier (product) is free from defects in material and
workmanship, under normal and proper use, for a period of one (1) year from the date of purchase (as shown on the
original bill of sale with serial number affixed/written on it). The one (1) year warranty period is valid only if the product is
properly installed by an Earthquake authorized party, and the warranty registration card is properly filled out and sent to
Earthquake Sound Corporation. If the product is installed by a non-authorized dealer, a thirty (30) day warranty
period applies.
(A) One (1) year limited warranty guidelines: (If installed by an authorized Earthquake dealer)
First year: Earthquake pays for labor, parts, and ground freight (only in US mainland) back to customer.
(B) Warning:
- Products (sent for repair) that are tested by Earthquake technicians and deemed to have no problem, will not be
covered by the limited warranty. Customer will be charged a minimum of one (1) hour of labor (ongoing rates) plus
shipping charges back to customer.
- Each product sent for repair must be packaged in its original packaging. Otherwise, there will be repackaging
charge in addition to labor, parts and shipping charges.
© Earthquake agrees to repair or replace - at our option - all such defective products/parts subject to the following
provisions:
- Defective products/parts have not been altered or repaired by other than an Earthquake factory approved
technician.
- Products/parts are not subjected to negligence, misuse, improper use, or accident, damaged by improper line
voltage, used with incompatible products, or have its serial number or any part of it altered, defaced or removed,
or have been used in any way that is contrary to Earthquake's written instructions.
(D) Warranty Limitations:
Earthquake warranty does not cover products that have been modified or abused. Including but not limited to the
following
- Damages to speaker cabinet and cabinet finish due to misuse, abuse, or use of improper use of cleaning
materials/methods.
- Bent speaker frame, broken speaker connectors, holes in speaker cone, surround & dust cap, burnt speaker
voice coil.
- Fading, deterioration of speaker components & finish due to improper exposure to elements.
- Bent amplifier casing, damaged finish on the casing due to abuse, misuse, or improper use of cleaning material.
- Burnt tracers on PCB.
- Product/part damaged due to poor packaging or abusive shipping conditions.
- Subsequent damage to other products.
A warranty claim will not be valid if the warranty registration card is not properly filled & returned to Earthquake with a copy
of the purchase receipt.
(E) Service Request:
To receive product(s) service, contact Earthquake service department at (510) 732-1000 and request an RMA
number (Return Material Authorization), items shipped without a valid RMA number will be refused. Make sure you
provide us with your complete/correct shipping address, a valid phone number, and a brief description of the problem you
are experiencing with the product. In most cases, our technicians might be able to resolve the problem over the phone,
thus eliminating the need to ship the product.
(F) Shipping Instructions:
Product(s) must be packaged in its original protective box(es) to minimize transport damage and avoid
repackaging charges. Shipper claims regarding items damaged in transit must be presented to carrier. Earthquake
Sound Corporation reserves the right to refuse products that are improperly packaged. A copy of the purchase receipt
must accompany product returned for service. We encourage you to include with the package a written description of the
problem. Ship product to: Earthquake Sound Corp. 2727 Mc Cone Avenue, Hayward, CA 94545. Ph (510) 732-1000. You
are responsible for the cost of shipping the product to Earthquake Sound Corporation.
(G) Disputes Resolution:
All disputes - between clients and Earthquake Sound Corporation - resulting from the one (1) year limited
warranty policy must be resolved according to the laws & regulations of the county of Alameda -California.
• 5 1/4” woofer with polycone with butyl rubber surround
• ½” Mylar tweeter
Granite-52 is a pair of left and right speakers with an unconventional coaxial design. The tweeter is mounted
on the same shaft of the speaker and in a typical speaker, the shaft requires a small opening for movement.
This allows moisture to pass the waterproof cone and get into the voice coil, damaging the speaker.
Earthquake engineers solved this problem by developing the world’s first rubber spider. This injection molded
rubber is shaped like a spider which is waterproof and extremely durable under weather conditions. The
spider acts as a soft suspension yet serves as a moisture barrier.
The Granite-52 speakers are made with a waterproof poly propylene injection molded cone. The surround is
made of butyl rubber and the front of the shaft is totally sealed from the back so no water will get trapped
inside.
Granite-10D Design
Granite-52 Design
Specifications
ROCK-on Manual 8
Earthquake Sound Corp. | (800) 576-7944 | www.earthquakesound.com
Frequency
Response (±3dB)
50Hz-21kHz
30Hz-100Hz
Recommended
Amplifier Power
40-200 Watts20-400 Watts
Nominal Impedance
Sensitivity(1W@1M)
93dB
92dB
Woofer
5 1/4”
(133mm)
10” (254mm)
Two 2.5” diameter voice coils
Tweeter
½” (13mm)
Mylar
N/A
Dimensions
(HxWxD)
8 1/2” (216mm)
8 1/2” (216mm)
9” (229mm)
14” (356mm)
18 1/2” (470mm)
21” (546mm)
Finish
Granite rockGranite rock
Enclosure
15mm epoxy resin
15mm epoxy resin
Granite-10D
Granite-52
• 10” long excursion dual coil driver
• 2.5” diameter voice coil with 1.5” winding height
Granite-10D is a dual voice coil long excursion subwoofer. It has a massive motor that is unconventional in the
outdoor rock speaker market. The voice coil has a whopping 2.5” diameter and 1.5” winding height. The
overall excursion is over 2” peak to peak. Due to its voice coil winding height, the Granite-10D produces more
sound pressure level, SPL, while using less current from your amplifier.
Conventional rock speakers are totally sealed and will heat up to a temperature that exceeds 180 degrees. So
as soon as you turn on the music, the rock speaker only gets hotter. Not the Granite-10D.
Granite-10D has a clever ported design that allows the subwoofer to release the hot air. This port is a tube that
has an opening in the lower back side but extends upward inside the box to prevent moisture and water from
being trapped inside. In addition to keeping the subwoofer cool, this port adds 3dB of bass. 3dB is equal to half
the volume.
Like the Granite-52, the Granite-10D also has a poly propylene injection molded cone with a butyl rubber
surround.
1 Year Limited Warranty Information
ROCK-on Manual 9
Specifications are subject to change without notice.
It Is Recommended That You Place Your Serial Number Here For Reference
ROCK-on Granite-52 and Granite-10D one (1) year limited warranty:
Earthquake warrants the original purchaser that the speaker or amplifier (product) is free from defects in material and
workmanship, under normal and proper use, for a period of one (1) year from the date of purchase (as shown on the
original bill of sale with serial number affixed/written on it). The one (1) year warranty period is valid only if the product is
properly installed by an Earthquake authorized party, and the warranty registration card is properly filled out and sent to
Earthquake Sound Corporation. If the product is installed by a non-authorized dealer, a thirty (30) day warranty
period applies.
(A) One (1) year limited warranty guidelines: (If installed by an authorized Earthquake dealer)
First year: Earthquake pays for labor, parts, and ground freight (only in US mainland) back to customer.
(B) Warning:
- Products (sent for repair) that are tested by Earthquake technicians and deemed to have no problem, will not be
covered by the limited warranty. Customer will be charged a minimum of one (1) hour of labor (ongoing rates) plus
shipping charges back to customer.
- Each product sent for repair must be packaged in its original packaging. Otherwise, there will be repackaging
charge in addition to labor, parts and shipping charges.
© Earthquake agrees to repair or replace - at our option - all such defective products/parts subject to the following
provisions:
- Defective products/parts have not been altered or repaired by other than an Earthquake factory approved
technician.
- Products/parts are not subjected to negligence, misuse, improper use, or accident, damaged by improper line
voltage, used with incompatible products, or have its serial number or any part of it altered, defaced or removed,
or have been used in any way that is contrary to Earthquake's written instructions.
(D) Warranty Limitations:
Earthquake warranty does not cover products that have been modified or abused. Including but not limited to the
following
- Damages to speaker cabinet and cabinet finish due to misuse, abuse, or use of improper use of cleaning
materials/methods.
- Bent speaker frame, broken speaker connectors, holes in speaker cone, surround & dust cap, burnt speaker
voice coil.
- Fading, deterioration of speaker components & finish due to improper exposure to elements.
- Bent amplifier casing, damaged finish on the casing due to abuse, misuse, or improper use of cleaning material.
- Burnt tracers on PCB.
- Product/part damaged due to poor packaging or abusive shipping conditions.
- Subsequent damage to other products.
A warranty claim will not be valid if the warranty registration card is not properly filled & returned to Earthquake with a copy
of the purchase receipt.
(E) Service Request:
To receive product(s) service, contact Earthquake service department at (510) 732-1000 and request an RMA
number (Return Material Authorization), items shipped without a valid RMA number will be refused. Make sure you
provide us with your complete/correct shipping address, a valid phone number, and a brief description of the problem you
are experiencing with the product. In most cases, our technicians might be able to resolve the problem over the phone,
thus eliminating the need to ship the product.
(F) Shipping Instructions:
Product(s) must be packaged in its original protective box(es) to minimize transport damage and avoid
repackaging charges. Shipper claims regarding items damaged in transit must be presented to carrier. Earthquake
Sound Corporation reserves the right to refuse products that are improperly packaged. A copy of the purchase receipt
must accompany product returned for service. We encourage you to include with the package a written description of the
problem. Ship product to: Earthquake Sound Corp. 2727 Mc Cone Avenue, Hayward, CA 94545. Ph (510) 732-1000. You
are responsible for the cost of shipping the product to Earthquake Sound Corporation.
(G) Disputes Resolution:
All disputes - between clients and Earthquake Sound Corporation - resulting from the one (1) year limited
warranty policy must be resolved according to the laws & regulations of the county of Alameda -California.
• 5 1/4” woofer with polycone with butyl rubber surround
• ½” Mylar tweeter
Granite-52 is a pair of left and right speakers with an unconventional coaxial design. The tweeter is mounted
on the same shaft of the speaker and in a typical speaker, the shaft requires a small opening for movement.
This allows moisture to pass the waterproof cone and get into the voice coil, damaging the speaker.
Earthquake engineers solved this problem by developing the world’s first rubber spider. This injection molded
rubber is shaped like a spider which is waterproof and extremely durable under weather conditions. The
spider acts as a soft suspension yet serves as a moisture barrier.
The Granite-52 speakers are made with a waterproof poly propylene injection molded cone. The surround is
made of butyl rubber and the front of the shaft is totally sealed from the back so no water will get trapped
inside.
Sound That Will Move You
Earthquake Sound reserves the right to amend details of the specifications without notice.
© Copyright Earthquake Sound Corporation
Earthquake Sound Corporation
2727 McCone Avenue, Hayward CA, 94545
Phone: (510) 732-1000 Fax: (510) 732-1095
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
Earthquake Sound 52 User manual
- Category
- Soundbar speakers
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Earthquake Sound Granite-52 User manual
-
Earthquake Sound ACS3.0 Owner's manual
-
Earthquake Sound Granite ROCK-on Owner's manual
-
Earthquake Sound Nova FF6.5 Owner's manual
-
Earthquake Sound MiNi D3000.4 User manual
-
Earthquake Sound MAGMA-12X Owner's manual
-
Earthquake Sound AWS-502 User manual
-
Earthquake Sound Magma User manual
-
Earthquake Sound TNT-T46 User manual
-
Earthquake Sound DB-12 User manual
Other documents
-
VM Audio VMROCK6 Installation guide
-
Artsound MDC64 Datasheet
-
Dual LUR66E User manual
-
OEM Systems RS-69 User manual
-
EarthQuake EQ-4000BT v2 Owner's manual
-
OSD Audio Omni 360° Outdoor Rock Weather Resistant Owner's manual
-
OSD Audio RS670 Installation guide
-
-
-
