Danfoss 2 x 24 Character Serial Display Module User guide

Type
User guide

Danfoss 2 x 24 Character Serial Display Module is a cost-effective alpha-numeric display designed for demanding operating conditions and environments common to mobile machine applications. It integrates an industry-standard New Twisted Nematic (NTN) LCD alpha-numeric display glass with robust high-impact plastic packaging and interface electronics, allowing installation in no-cab and open-cab machines.

Danfoss 2 x 24 Character Serial Display Module is a cost-effective alpha-numeric display designed for demanding operating conditions and environments common to mobile machine applications. It integrates an industry-standard New Twisted Nematic (NTN) LCD alpha-numeric display glass with robust high-impact plastic packaging and interface electronics, allowing installation in no-cab and open-cab machines.

Technical Information
Displays
2 x 24 Character Serial Display Module
powersolutions.danfoss.com
Revision history Table of revisions
Date Changed Rev
April 2017 Updated to Engineering Tomorrow design 0102
November 2015 Converted to Danfoss layout 0101
August 2010 Replacement part numbers for modules 0100
November 2006 First edition 0000
Technical Information
2 x 24 Character Serial Display
2 |
©
Danfoss | April 2017 11017626 | BC00000029enUS0102
General Information
Product overview............................................................................................................................................................................. 4
Features................................................................................................................................................................................................4
Available models.............................................................................................................................................................................. 4
Theory of operation.........................................................................................................................................................................5
Character set...................................................................................................................................................................................... 6
Accessories..........................................................................................................................................................................................7
Technical data
Electrical...............................................................................................................................................................................................8
Environmental................................................................................................................................................................................... 8
Product installation
Dimensions.........................................................................................................................................................................................9
Wiring connections....................................................................................................................................................................... 10
Machine wiring guidelines......................................................................................................................................................... 11
Technical Information
2 x 24 Character Serial Display
Contents
©
Danfoss | April 2017 11017626 | BC00000029enUS0102 | 3
Product overview
The Danfoss 2 x 24 serial display module is designed for the demanding operating conditions and
environments common to mobile machine applications.
The display module integrates an industry standard New Twisted Nematic (NTN) LCD alpha numeric
display glass with robust high impact plastic packaging and interface electronics allowing installation in
no cab and open cab machines.
Superior readability in all ambient light conditions is accomplished through the use of a transflective,
backlit type of display with dark characters on a green background. An adjustable viewing angle option
(controlled via software) allows machine operators to adjust display contrast to compensate for changing
light conditions and operator position. Character clarity is enhanced by a 5 x 7 dot matrix character.
2 x 24 display modules are designed to be used in conjunction with Danfoss microcontrollers via RS232
serial communication. Danfoss electronics embedded in the display module convert serial character
transmission to the parallel format required by the display.
Features
Cost effective alpha numeric display
Rugged mechanical design for mobile applications
IP 65 rating above panel rating; resistant to high pressure wash down
Built in Danfoss serial to parallel card allows easy communication with display driver
LED backlight for very low light conditions
Dark characters on green background; excellent visibility in a wide variety of ambient light conditions
Suitable for 12 and 24 volt systems; option for 5 volt power
Extended operating temperature range
Operates in conjunction with most Danfoss microcontrollers
Fixed and operator adjustable viewing angles
Available models
2 x 24 Character Serial Display modules part numbers
Obsolete Replaced by Supply voltage and viewing position Recommended
microcontroller
10104202 11076372 5 to 15 Vdc; direct horizon view, adjustable S2X, MC300
10105224 11076377 5 to 15 Vdc; 30 to 45° above horizon, adjustable S2X, MC300
10104198 11076366 5 to 15 Vdc; Direct horizon view, not adjustable S2X, MC300
10104210 11076389 9 to 32 Vdc; Direct horizon view, adjustable S1X, MC400
10105225 11076396 9 to 32 Vdc; 30 to 45° above horizon, adjustable S1X, MC400
10104206 11076382 9 to 32 Vdc; Direct horizon view, not adjustable S1X, MC400
Technical Information
2 x 24 Character Serial Display
General Information
4 |
©
Danfoss | April 2017 11017626 | BC00000029enUS0102
Theory of operation
Danfoss 2 x 24 Display Modules are designed to operate in conjunction with Danfoss microcontrollers.
The generation of display messages is typically an integral part of the application program running in the
microcontroller. Character information is transmitted from the microcontroller to the display module via
RS232 standard signal levels and protocol operating at 9600 Baud.
Danfoss proprietary interface electronics embedded in the display module converts microcontroller serial
data to the parallel data format required by the LCD display driver. The Display Module is a receive only
device and does not return any information to the microcontroller.
Display readability is influenced by two parameters:
The operator’s spatial relationship to the display and the display viewing angle (also referred to as
viewing cone).
Spatial relationship can be described as either direct horizon view or 30 to 45 degrees above horizon.
See the following illustration.
Display viewing angle can be either fixed or variable. Fixed viewing angle displays have a factory set
voltage that cannot be adjusted after manufacture. Variable viewing angle (also referred to as
contrast) is controlled by varying the voltage applied to the capacitive fluid in the display glass which
changes the alignment of display particles.
Variable displays allow the user to adjust display glass contrast control voltage in a step-wise manner
through software control from the microcontroller. The display voltage control range is controlled over
100 steps. Variable displays are typically used in applications where there is no cab and variable lighting
conditions.
Displays with variable viewing angles will default to the most recent control voltage at power-up.
Operators spacial relationship to the display and the display viewing angle
kwa1392482101022
1
2
1 30 to 45° horizontal view
2 Direct horizontal view
Technical Information
2 x 24 Character Serial Display
General Information
©
Danfoss | April 2017 11017626 | BC00000029enUS0102 | 5
Character set
Each of the 48 display module character locations contain a five by seven dot matrix. The display
supports the following standard and special LCD character sets:
Standard character set
Danfoss special
0 x 00 = 0 x 01 = 0 x 02 = 0 x 03 = 0 x 04 = 0 x 05 =
0 x 06 =
0 x 07 =
kwa1392482107875
Display character locations
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
kwa1392482111937
Technical Information
2 x 24 Character Serial Display
General Information
6 |
©
Danfoss | April 2017 11017626 | BC00000029enUS0102
Accessories
Mating connector cable assemblies
Part number Microcontroller Description
1090025 S2X, MC300 Molded right angle display mating connector and 6 pin
microcontroller MS Pigmy mating connector, 213.36 cm
[84 in] length.
K19853 S1X and MC400 Molded right angle display mating connector and bare
tinned leads 213.36 cm [84 in] length.
Technical Information
2 x 24 Character Serial Display
General Information
©
Danfoss | April 2017 11017626 | BC00000029enUS0102 | 7
Electrical
Electrical characteristics
Part number Supply voltage Current consumption RS232 baud rate
10104202, 10105224, 10104198 5 to 15 Vdc 200 mA 9600
10104210, 10105225, 10104206 9 to 32 Vdc 200 mA 9600
Transient suppression
Protected against static discharge
Environmental
IP 65 Rating above panel. Withstands high pressure wash and high humidity typical in mobile machine
operations.
Environmental characteristics
Operating temperature Storage temperature
-30° C to +70° C [-22° F to +158° F] -20° C to +70° C [-4° F to +158° F]
Technical Information
2 x 24 Character Serial Display
Technical data
8 |
©
Danfoss | April 2017 11017626 | BC00000029enUS0102
Dimensions
2 x 24 Character Serial Display Module installation dimensions in millimeters [inches]
99.31
[3.91]
12.95
[0.51]
32.26
[1.27]
32.26
[0.25]
234.95
[9.25]
127.00
[5.00]
2 X 11.94 [.47]
37.34
[1.47]
7.11
[0.28]
74.68
[2.94]
60.33
[2.375]
222.25
[8.75]
127.00
[5.00]
47.75
[1.88]
50.80
[2.00]
60.33
[2.375]
4.83
[0.19]
60.33
[2.375]
kwa1392482121986
1
2
1 4 X 4.83 [.190] DIA THRU and CBORE 9.14 [.36 ] DIA X 4.06 [.16] DP
2 #8-32UNC-2B THREADS
Technical Information
2 x 24 Character Serial Display
Product installation
©
Danfoss | April 2017 11017626 | BC00000029enUS0102 | 9
Wiring connections
8 [.31] x 6.3 [.25] BAYONET electrical connectors WECO electrical connectors Part number 900-SUN-7.5
8 7
- +
kwa1392482130370
5 to 15 Vdc power supply models
Pin Function
1 Ground
2 Ground
3 Not used
4 Not used
5 RS232 IN
6 5 to 15 V DC device power
7 Alternate 5 to 15 V DC device power
8 Alternate device ground
6 pin CONXALL MULTI-CON-X Part number 4285-6
1
2
3
4
5
6
kwa1392482135559
9 to 32 Vdc power supply models
Pin Function
1 Ground
2 Ground
3 9 to 32 Vdc device power
*
4 Ground
5 RS232 IN
6 9 to 32 V DC device power
7 Alternate 9 to 32 V DC device power
8 Alternate device ground
*
Only one power connection is required.
C
Caution
Potential property damage.
Connect all ground pins on 6 pin connector to vehicle ground.
Technical Information
2 x 24 Character Serial Display
Product installation
10 |
©
Danfoss | April 2017 11017626 | BC00000029enUS0102
Machine wiring guidelines
Protect wires from mechanical abuse, run wires in flexible metal or plastic conduits.
Use 85˚ C (185˚ F) wire with abrasion resistant insulation and 105˚ C (221˚ F) wire should be
considered near hot surfaces.
Use a wire size that is appropriate for the module connector.
Separate high current wires such as solenoids, lights, alternators or fuel pumps from sensor and other
noise-sensitive input wires.
Run wires along the inside of, or close to, metal machine surfaces where possible, this simulates a
shield which will minimize the effects of EMI/RFI radiation.
Do not run wires near sharp metal corners, consider running wires through a grommet when
rounding a corner.
Do not run wires near hot machine members.
Provide strain relief for all wires.
Avoid running wires near moving or vibrating components.
Avoid long, unsupported wire spans.
Ground electronic modules to a dedicated conductor of sufficient size that is connected to the
battery (-).
Power the sensors and valve drive circuits by their dedicated wired power sources and ground
returns.
Twist sensor lines about one turn every 10 cm (4 in).
Use wire harness anchors that will allow wires to float with respect to the machine rather than rigid
anchors.
W
Warning
Unintended movement of the machine or mechanism may cause injury to the technician or bystanders.
The module will be powered up if battery voltage is applied to the module's output pin. To protect
against unintended movement, secure the machine.
C
Caution
Warranty will be voided if module is damaged.
Avoid significant current driven back through an output pin.
Technical Information
2 x 24 Character Serial Display
Product installation
©
Danfoss | April 2017 11017626 | BC00000029enUS0102 | 11
Danfoss Power Solutions is a global manufacturer and supplier of high-quality hydraulic and
electronic components. We specialize in providing state-of-the-art technology and solutions
that excel in the harsh operating conditions of the mobile off-highway market. Building on
our extensive applications expertise, we work closely with our customers to ensure
exceptional performance for a broad range of off-highway vehicles.
We help OEMs around the world speed up system development, reduce costs and bring
vehicles to market faster.
Danfoss – Your Strongest Partner in Mobile Hydraulics.
Go to www.powersolutions.danfoss.com for further product information.
Wherever off-highway vehicles are at work, so is Danfoss. We offer expert worldwide support
for our customers, ensuring the best possible solutions for outstanding performance. And
with an extensive network of Global Service Partners, we also provide comprehensive global
service for all of our components.
Please contact the Danfoss Power Solution representative nearest you.
Local address:
Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products
already on order provided that such alterations can be made without changes being necessary in specifications already agreed.
All trademarks in this material are property of the respective companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.
©
Danfoss | April 2017 11017626 | BC00000029enUS0102
Products we offer:
Bent Axis Motors
Closed Circuit Axial Piston
Pumps and Motors
Displays
Electrohydraulic Power
Steering
Electrohydraulics
Hydraulic Power Steering
Integrated Systems
Joysticks and Control
Handles
Microcontrollers and
Software
Open Circuit Axial Piston
Pumps
Orbital Motors
PLUS+1
®
GUIDE
Proportional Valves
Sensors
Steering
Transit Mixer Drives
Comatrol
www.comatrol.com
Turolla
www.turollaocg.com
Hydro-Gear
www.hydro-gear.com
Daikin-Sauer-Danfoss
www.daikin-sauer-danfoss.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Danfoss 2 x 24 Character Serial Display Module User guide

Type
User guide

Danfoss 2 x 24 Character Serial Display Module is a cost-effective alpha-numeric display designed for demanding operating conditions and environments common to mobile machine applications. It integrates an industry-standard New Twisted Nematic (NTN) LCD alpha-numeric display glass with robust high-impact plastic packaging and interface electronics, allowing installation in no-cab and open-cab machines.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI