2. Danfoss
  3. DHP-C

Danfoss DHP-C Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Danfoss DHP-C Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Electrical
installation instructions
Danfoss Heat Pumps
DHP-C
VWBMH202
DHP-C
Electrical installation – Page 2
VWBMH202
Contents
DHP-C 6 .................. 3–6
DHP-C 8 ..................7-10
DHP-C 10 ............... 11–14
DHP-C 4H ............... 15–18
DHP-C 5H ............... 19–22
DHP-C 7H ................23-26
Electrical installation
Danfoss heat pumps are factory-wired internally. The leads that are to
be connected are the mains supply (5-wire DPH), outdoor temperature
sensor and room sensors (if any).
• Allelectricalwiringmustbecarriedoutbyacertifiedelectricianin
compliance with local and national codes and regulations. When in
doubt, contact the local electricity distributor.
•Themainsleadispassedthroughthetopoftheunit.
•Removethefrontpaneltogetaccesstotheterminalblocks.Connect
themainsleadtotheterminalblockaccordingtotheaccompanying
schematic diagram.
•Theconnectionoftheheatpumptothemainssupplymustbehard-
wired and a multi-pole switch
(safety switch) must be installed in the power supply line to the unit.
WARNING! To disconnect the power supply to the heat pump, the
safety switch must be switched off.
NOTE! Thecablestotheoutdoorandindoorsensorscarrylowvoltage.
Interference from surrounding cables may affect these and cause incor-
rect information to be sent to the control unit. It is therefore vitally
important thatcarefulconsiderationbegivento positioning ofcables.
Low-voltage cables must be kept well separated from high-voltage
cables.It is importantthatlow-voltage cables are run parallel to high-
voltagecablesandseparatedby a distance of at least 25 cm for cable
lengths up to 100 m. For longer cable lengths, the distance between
cables should be increased.
Important information
Before switching on the power supply to the heat pump, you must
ensure that the heating system, chilled water line and hot water heater
arefilledandvented.Otherwise,thecirculationpumpscanbeseverely
damaged.
DHP-C
Electrical installation – Page 3
VWBMH202
DHP-C
Electrical installation – Page 4
VWBMH202
DHP-C
Electrical installation – Page 5
VWBMH202
DHP-C
Electrical installation – Page 6
VWBMH202
DHP-C
Electrical installation – Page 7
VWBMH202
DHP-C
Electrical installation – Page 8
VWBMH202
DHP-C
Electrical installation – Page 9
VWBMH202
DHP-C
Electrical installation – Page 10
VWBMH202
DHP-C
Electrical installation – Page 11
VWBMH202
DHP-C
Electrical installation – Page 12
VWBMH202
DHP-C
Electrical installation – Page 13
VWBMH202
DHP-C
Electrical installation – Page 14
VWBMH202
DHP-CH
Electrical installation – Page 15
VWBMH202
DHP-CH
Electrical installation – Page 16
VWBMH202
DHP-CH
Electrical installation – Page 17
VWBMH202
DHP-CH
Electrical installation – Page 18
VWBMH202
DHP-CH
Electrical installation – Page 19
VWBMH202
DHP-CH
Electrical installation – Page 20
VWBMH202
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/