Danfoss DHP-C Installation guide

Danfoss
Brand
Danfoss
Model
DHP-C
Type
Installation guide
Electrical
installation instructions
Danfoss Heat Pumps
DHP-C
VWBMH102
DHP-C
Electrical installation – Page 2
VWBMH102
Contents
DHP-C
DHP-C 6 .............. 3–6
DHP-C 8 .............. 7-10
DHP-C 10 ........... 11–14
DHP-CH
DHP-CH 4 ........... 15–18
DHP-CH 5 ........... 19–22
DHP-CH 7 ............ 23-26
Electrical installation
Danfoss heat pumps are factory-wired internally. The leads that are to be
connected are the mains supply (5-wire DPH), outdoor
temperature sensor and room sensors (if any).
• All electrical wiring must be carried out by a certified electrician in com-
pliance with local and national codes and regulations. When in doubt,
contact the local electricity distributor.
• The mains lead is passed through the top of the unit.
• Remove the front panel to get access to the terminal blocks. Connect
the mains lead to the terminal block according to the accompanying
schematic diagram.
• The connection of the heat pump to the mains supply must be hard-
wired and a multi-pole switch
(safety switch) must be installed in the power supply line to the unit.
WARNING!
To disconnect the power supply to the heat pump, the safety
switch must be switched off.
NOTE!
The cables to the outdoor and indoor sensors carry low vol-
tage. Interference from surrounding cables may affect these and cause
incorrect information to be sent to the control unit. It is therefore vitally
important that careful consideration be given to positioning of cables.
Low-voltage cables must be kept well separated from high-voltage cables.
It is important that low-voltage cables are run parallel to high- voltage
cables and separated by a distance of at least 25 cm for cable lengths
up to 100 m. For longer cable lengths, the distance between cables
should be increased.
Important information
Before switching on the power supply to the heat pump, you must ensure
that the heating system, chilled water line and hot water heater are filled
and vented. Otherwise, the circulation pumps can be severely damaged.
DHP-C
Electrical installation – Page 3
VWBMH102
DHP-C
Electrical installation – Page 4
VWBMH102
DHP-C
Electrical installation – Page 5
VWBMH102
DHP-C
Electrical installation – Page 6
VWBMH102
DHP-C
Electrical installation – Page 7
VWBMH102
DHP-C
Electrical installation – Page 8
VWBMH102
DHP-C
Electrical installation – Page 9
VWBMH102
DHP-C
Electrical installation – Page 10
VWBMH102
DHP-C
Electrical installation – Page 11
VWBMH102
DHP-C
Electrical installation – Page 12
VWBMH102
DHP-C
Electrical installation – Page 13
VWBMH102
DHP-C
Electrical installation – Page 14
VWBMH102
DHP-CH
Electrical installation – Page 15
VWBMH102
DHP-CH
Electrical installation – Page 16
VWBMH102
DHP-CH
Electrical installation – Page 17
VWBMH102
DHP-CH
Electrical installation – Page 18
VWBMH102
DHP-CH
Electrical installation – Page 19
VWBMH102
DHP-CH
Electrical installation – Page 20
VWBMH102
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Danfoss DHP-C Installation guide

Danfoss
Brand
Danfoss
Model
DHP-C
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers