VTech IA5874 User manual

www.vtechphones.com TABLE OF CONTENTS

1

Table of Contents

GETTING STARTED. . . . . . . . . . . . . . . . . . . 4

Before You Begin . . . . . . . . . . . . . . . . . . . . . 4

Parts Check List: . . . . . . . . . . . . . . . . . . . 4

Installation . . . . . . . . . . . . . . . . . . . . . . . . 5

Choose Location . . . . . . . . . . . . . . . . . . . 5

Install Handset Battery . . . . . . . . . . . . . . . . 5

Connect Power and Telephone Line Cords . . . . . . 6

Wall Mounting . . . . . . . . . . . . . . . . . . . . . 7

Desk/Table Installation . . . . . . . . . . . . . . . . 7

Charge the Handset Battery . . . . . . . . . . . . . 8

Set Language Mode . . . . . . . . . . . . . . . . . 8

Check for Dial Tone . . . . . . . . . . . . . . . . . . 8

Set the Dial Mode . . . . . . . . . . . . . . . . . . . 8

Set Handset Date and Time. . . . . . . . . . . . . . 9

Handset Ringer Style/Battery Save . . . . . . . . . . 9

If you subscribe to DSL service: . . . . . . . . . . .10

Belt clip (optional) . . . . . . . . . . . . . . . . . . .10

BASIC OPERATION . . . . . . . . . . . . . . . . . . 11

Telephone Operation . . . . . . . . . . . . . . . . . . 11

Handset Operation . . . . . . . . . . . . . . . . . .11

Base Operation . . . . . . . . . . . . . . . . . . . .12

Temporary Tone Dialing . . . . . . . . . . . . . . .12

Message Waiting . . . . . . . . . . . . . . . . . . .12

Clear Message Waiting Alert . . . . . . . . . . . . .13

Headset Jack . . . . . . . . . . . . . . . . . . . . .14

Operating Range . . . . . . . . . . . . . . . . . . .14

Display Screen Messages . . . . . . . . . . . . . .15

Speed Dialing . . . . . . . . . . . . . . . . . . . . . . 16

Store a Number/Name in Speed Dial . . . . . . . . .16

Edit a Number/Name Stored in Speed Dial . . . . . .17

Delete a Number/Name Stored in Speed Dial . . . .18

Dial a Speed Dial Number . . . . . . . . . . . . . .18

Reassign Locations in Speed Dial . . . . . . . . . .18

Telephone Directory . . . . . . . . . . . . . . . . . . 19

Store a Number/Name in the Directory . . . . . . . .19

Edit a Number/Name Stored in the Directory . . . . .19

Delete a Number/Name Stored in the Directory . . .20

Move a Number/Name to the Speed Dial Memory . .21

Dial a Number from the Directory . . . . . . . . . . .21

Caller ID . . . . . . . . . . . . . . . . . . . . . . . . 22

About Call History (Caller ID) . . . . . . . . . . . . .23

Review Call History . . . . . . . . . . . . . . . . . .23

Delete Records from Call History . . . . . . . . . . .24

Dial a Displayed Number . . . . . . . . . . . . . . .24

Store a Call History Record in the Directory . . . . .24

Display Screen Messages . . . . . . . . . . . . . .25

Answering System Operation At the Base . . . . . . . 26

Audible Indicators . . . . . . . . . . . . . . . . . . .26

Setting the clock. . . . . . . . . . . . . . . . . . . .26

About Announcements . . . . . . . . . . . . . . . .26

Record Your Announcement . . . . . . . . . . . . .27

To review your announcement at any time: . . . . . .27

To delete your announcement: . . . . . . . . . . . .27

Setting up your answering system . . . . . . . . . .28

Feature summary . . . . . . . . . . . . . . . . . . .28

Listen to, Save & Delete Messages . . . . . . . . . .29

Call Screening/Intercept. . . . . . . . . . . . . . . .30

Record a Memo . . . . . . . . . . . . . . . . . . . .30

Window display . . . . . . . . . . . . . . . . . . . .31

Answering System Operation - Remote Access . . . . 32

TABLE OF CONTENTS www.vtechphones.com

2

Connect with the Answering System . . . . . . . . .32

Voice Menu . . . . . . . . . . . . . . . . . . . . . .32

Remote Access Commands . . . . . . . . . . . . .32

Batteries . . . . . . . . . . . . . . . . . . . . . . . . 34

Battery Care and Maintenance . . . . . . . . . . . .34

Replacing the Handset Battery . . . . . . . . . . . .34

ADDITIONAL INFORMATION . . . . . . . . . . . . . .35

Troubleshooting. . . . . . . . . . . . . . . . . . . . . 35

Maintenance . . . . . . . . . . . . . . . . . . . . . . 42

Warranty Statement. . . . . . . . . . . . . . . . . . . 42

Important Safety Instructions . . . . . . . . . . . . . . 44

FCC, ACTA and IC Regulations . . . . . . . . . . . . 45

The RBRC

®

Seal . . . . . . . . . . . . . . . . . . . . 46

Technical Specications . . . . . . . . . . . . . . . . 47

Index . . . . . . . . . . . . . . . . . . . . . . . . . . 48

NEED HELP?

This book has all the feature operation and troubleshooting you need to install

and operate your new VTech phone. Please take the time to review thoroughly

to ensure proper installation and the benet of this VTech innovative and feature

rich product. You can also visit our website at www.vtechphones.com for support,

shopping, and everything new at VTech.

In Canada, please visit www.vtechcanada.com.

VTech toll free 1-800-595-9511

In Canada dial 1-800-267-7377

www.vtechphones.com

4

Before You Begin

GETTING STARTED

Enhanced 5.8GHz Technology - Dual band transmission combines the best of 5.8GHz

and 900MHz technologies, providing enhanced performance over standard cordless

telephones.

1. Base Unit

2. Handset

3. Telephone Line Cord

4. Desk/Wall Mount Bracket

5. Belt Clip

6. Base Power Adaptor

7. Battery

8. User’s Manual

To purchas e rep la ce me nt

batteries, visit us on the web

at www.vtechphones.com or

call VTech Communications,

Inc. at 1-800-595-9511. In

C a n a d a , c o n t a c t V T e c h

Telecommunications Canada

Ltd. at www.vtechcanada.com

or 1-800-267-7377.

Parts Check List:

Base Unit

Handset

Battery

Belt Clip

Telephone Line Cord

Base Power Adaptor

Desk/Wall Mount Bracket

User’s Manual

• Important!

B e f o r e u s i n g

this telephone,

you must read

Important Safety

Instructions on

page 44.

www.vtechphones.com

5

GETTING STARTED

Getting Started

Installation

Choose Location

For maximum performance of your

cordless telephone system:

1. Choose a central location for

your base unit.

2. Install your base unit and

handset away from electronic

equipment, such as personal

computers, television sets and

microwave ovens.

3. In locations where there are

multiple cordless telephones,

separate base units as much as

possible.

4. Install your telephone

equipment away from heat

sources and sunlight.

5. Avoid excessive moisture, dust

or extreme cold.

a) Remove battery

compartment cover

by pressing on the

indentation and

sliding downwards.

b) Align the two holes in the plug with

the socket pins, then snap the plug

into place.

c) Place the battery in the compartment with

the wires in the lower right corner.

d) Replace cover by sliding it up into place.

e) Place the handset in its base when

not in use to ensure maximum daily

performance.

• U s e o n l y t h e

provided VTech

b a t t e r y , o r

equivalent.

Install Handset Battery

1

2

www.vtechphones.com

6

GETTING STARTED

Installation

Connect Power and Telephone Line Cords

Modular

telephone jack

Standard

electrical outlet

Connect the power cord. After

charging the battery for at least

16 hours, connect the telephone

line cord.

• Install the base unit

away from electronic

equipment such

a s p e r s o n a l

computers,

television sets or

microwave ovens.

Avoid excessive

heat, cold, dust or

moisture.

• Connect the power

a nd t e l ep h o n e

line cords to the

underside of the

base as illustrated.

• P l u g t h e A C

adapter into an

electrical outlet. If

the battery has not

been previously

charged,

place the handset in

the base, and allow

it to charge for 16

hours (or overnight).

Connect

the telephone line

cord to the wall

jack.

www.vtechphones.com

7

GETTING STARTED

Getting Started

Installation

Wall Mounting

Your phone base unit is designed to mount on a standard telephone wall plate. Wall mounting

is optional. See position one below for instructions.

Desk/Table Installation

To place your base unit on a desk or table, insert the desk/wall bracket as instructed below and shown

in position one or two, depending on your preference of how you’d like the base unit to be angled.

Position One

To mount your phone on a wall, or to place it on a table or desk, refer to the diagrams illustrating

position one.

• First insert the lower portion of the bracket into the grooves in the base, then snap the upper portion

into place.

• Mount the base on the wall by positioning the base unit so the mounting studs will t into the holes

on the base and wall mount bracket. Slide the base unit down on the mounting studs until it locks

into place.

Position Two

This position is an alternate way to install your phone on a table or desk. Position two allows a different

viewing angle to your handset and base unit. Refer to the position two diagrams above.

• Insert the upper portion of the bracket into the grooves in the base.

• Snap the lower portion into place.





www.vtechphones.com

8

GETTING STARTED

Installation

Charge the Handset Battery

Place the handset in the base or charger. NEEDS CHARGING will appear on the handset. Charge

the battery for at least 16 hours the rst time.

Set Language Mode

• Press PROG, then press

▲

or

▼

until LANGUAGE is displayed. Press SELECT.

• The current setting blinks. Press

▲

or

▼

until the screen displays the correct language (English,

Spanish or French).

• Press SELECT to save your selection.

Check for Dial Tone

After the batteries are charged, pick up the handset and press PHONE; you should hear a dial tone.

If you do not, refer to the TROUBLESHOOTING section in the back of this user’s manual.

Set the Dial Mode

If you have touch tone service, the phone is ready to use as soon as the battery is charged. If you

have pulse (rotary) service, you’ll need to change the dial mode.

• Press PROG.

• Press

▲

or

▼

or until the screen displays DIAL MODE: and the current setting.

• Press SELECT. The current setting blinks.

• Press

▲

or

▼

to select TONE or PULSE.

• Press SELECT to save.

• If the phone will

not be used for a

long period of time,

remove the battery

to prevent possible

leakage.

• If you have any

trouble installing

y o u r p h o n e ,

please refer to the

Troubleshooting

s e c t i o n n e a r

the end of this

manual.

www.vtechphones.com

9

GETTING STARTED

Getting Started

Installation

Set Handset Date and Time

If you subscribe to caller ID service, the date and time will be set automatically with the rst incoming

call. If you do not have caller ID service, you can set the date and time manually:

• Press PROG, then press

or

until DATE/TIME is displayed. Press SELECT.

• The month is ashing. Press

or

until the screen displays the correct month. Press SELECT.

• The day is ashing. Press

or

until the screen displays the correct day. Press SELECT.

• The hour is ashing. Press

or

until the screen displays the correct hour. Press SELECT.

• The minute is ashing. Press

or

until the screen displays the correct minute. Press SELECT.

• AM or PM is ashing. Press

or

to choose between AM or PM. Press SELECT

Handset Ringer Style/Battery Save

You can select from four different handset ringer styles, or turn the ringer off and extend the

battery life.

1. With the handset in idle (off) mode, press PROG.

2. Press

or

until the screen displays RINGER: and current setting.

3. Press SELECT. The current setting blinks, and you will hear a sample of the ring.

4. Press

or

to select RINGER: 1, 2, 3, 4 or OFF. You will hear a sample of each ring tone.

5. Press SELECT to choose the displayed ringer setting.

• In the event of a

power outage, or if

your phone’s power

cord is unplugged,

the time setting will

be lost.

www.vtechphones.com

10

GETTING STARTED

If you subscribe to DSL service:

If you hear noise during conversations and/or your caller ID features aren’t functioning properly, install

a noise lter to the telephone line between the base unit and the telephone line jack. Contact your DSL

provider to obtain a noise lter.

Belt clip (optional)

Installation

To remove

To attach

Telephone

line cord

Noise lter (For

DSL users)

To single telephone

jack (RJ11C)

www.vtechphones.com

11

Basic Operation

BASIC OPERATION

Telephone Operation

Handset Operation

1. Make a Call

Press PHONE, then dial the

number.

-OR-

Dial the number (use

to backspace and make

corrections), then press

PHONE to call.

2. Flash/Call Waiting

During a call, press to receive

an incoming

call, if call waiting is

activated.

3. Channel

Press CHAN to switch to a

clear channel while on a call.

4. Delete

When viewing the call log,

press to delete the current

record displayed. While

handset is in idle mode, press

and hold to delete all records

in the call log.

5. Answer a Call

Press any key to answer a

call (except OFF).

6. /CID and /DIR

/CID

• While on a call, press to

decrease the volume. A

double beep will sound

when you reach the lowest

setting.

• While phone is not in use,

press to display caller ID

information.

• While entering names or

numbers into memory,

press to delete last

character entered.

/DIR

• While on a call, press to

increase the volume. A

double beep will sound

when you reach the

highest setting.

• While phone is not in

use, press to display

directory entries.

• While entering names or

numbers, press to add a

space.

7. Select

Press to display menu, or

to select highlighted item

from menu.

8. Off

During a call, press to

hang up. While using

menus, press to cancel an

operation, back up, or exit

the menu display

9. Redial/Pause

Press to view redial

memory. While entering

numbers, press and hold to

insert a dialing pause.

10. Program

With the handset in idle

(on-hook), press to enter

programming mode.

1,2

3,4

8

7

9

10

5

6

www.vtechphones.com

12

BASIC OPERATION

Telephone Operation

Base Operation

11. CHARGE/IN USE

• Flashes in unison with an incoming call’s ringing.

• Flashes slowly when the handset is in use, or the answering

system is answering a call.

• Glows steadily when the handset is charging.

12. LOCATE HANDSET

Press to page the handset for up to 60 seconds. Press again,

press OFF on handset or place handset in base to cancel the

page.

11

12

Temporary Tone Dialing

If you have pulse (rotary) service, you can change from dial pulse to touch tone dialing during a call by

pressing * TONE. This is useful if you need to send touch tone signals for access to telephone banking

or long distance services.

1. Dial the number.

2. Press

*

TONE. Buttons pressed after this send touch tone signals.

3. After you hang up, the phone automatically returns to pulse service.

Message Waiting

Your phone is designed to work with most local and regional telephone service provider’s voice

messaging systems to provide an alert on handset when new messages come in. Voice messaging is

a subscription service, available through most service providers for a monthly fee. Contact your local

telephone company for more information.

www.vtechphones.com

13

Basic Operation

BASIC OPERATION

Telephone Operation

When you have a message waiting, the handset will display:

Clear Message Waiting Alert

If after you review your message(s) your message waiting alert does not go off, you may manually

turn it off by:

1. Press PROG on the handset.

2. Press or until screen displays MESSAGE WAITING.

3. Press SELECT, the screen display: CLEAR? YES

4. Press or to change from YES to NO.

5. Press SELECT, you’ll hear a conrmation tone.

MESSAGE WAITING

5/01 5:40PM

www.vtechphones.com

14

BASIC OPERATION

Operating Range

This cordless telephone operates within the maximum

power allowed by the Federal

Communications Commission (FCC). Even so, this

handset and base can communicate over only a

certain distance - which can vary with the locations

of the base and handset, the weather, and the

construction of your home or ofce. If you receive a

call while you are out of range, the handset might not

ring or if it does ring, the call might not connect when

you press PHONE. Move closer to the base, then

press PHONE to answer the call.

If you move out of range during a phone conversation,

you might hear noise or interference. To improve

reception, move closer to the base.

If you move out of range without pressing OFF, your

phone will be left off the hook. To hang up properly,

walk back into range, periodically pressing OFF.

• T o pu rc has e a

headset, visit us

on the web at www.

vtechphones.com

or call VTech Cus-

tomer Service at

1-800-595-9511.

In Canada, contact

VTech Telecommu-

nications Canada

Ltd. at www.vtech-

canada.com or 1-

800-267-7377.

Headset Jack

You can use this telephone handsfree

when you install any VTech 2.5 mm

headset, purchased separately.

Plug the headset into the jack located

on the right side of the handset (under

the small rubber ap). Do not force the

connection, but make sure the plug ts

securely.

Telephone Operation

www.vtechphones.com

15

Basic Operation

BASIC OPERATION

Telephone Operation

Display Screen Messages

Screen Displays: When:

** RINGING **

There is a call coming in.

CONNECTING...

The handset is waiting for dial tone.

PHONE ON

The handset is in use.

** PAGING **

The base is paging the handset.

BATTERY LOW

The battery needs to be recharged.

SCANNING...

The handset is changing to another of the

30 channels available.

CAN’T CONNECT

1. Displays when base power is off and

PHONE is pressed. You’ll also hear a sad

tone.

2. Displays when an out-of-range dial fails to

connect.

RINGER OFF

The handset ringer is turned off.

MESSAGE WAITING

Displays when you have been alerted by the

telephone company that you have received

new voice mail.

www.vtechphones.com

16

BASIC OPERATION

Speed Dialing

Presses

Dial Key Once Twice 3 Times 4 Times 5 Times 6 Times

1

2

A B C 2

3

D E F 3

4

G H I 4

5

J K L 5

6

M N O 6

7

P Q R S 7

8

T U V 8

9

W X Y Z 9

0

*

#

& ‘ , - . #

Your phone can store up to nine telephone numbers with names (up to 15 characters and 24 digits in

each location) in the speed dial memory locations you assign (numbered 1 through 9) in each handset.

These numbers can be dialed with two button presses. You can also store telephone numbers with

names alphabetically in the directory. See Telephone Directory for instructions.

Store a Number/Name in Speed Dial

1. Press PROG. Then press or until the screen displays SPEED DIAL.

2. Press SELECT. The screen displays ENTER 1-9.

3. Press the key (1 through 9) to assign the speed dial location this number will be stored. The screen

displays ENTER NAME.

4. Using the chart below, enter up to 15 characters for the name you’re storing. Use to backspace

and make corrections; use to advance and add a space.

• The entries you

st ore i n s pe ed

dial memory will

be marked with

01 through 09 and

also display in the

directory.

• Press OFF at any

time to exit speed

dial mode.

• W h e n m e m o r y

is full the screen

displays MEMORY

FULL, an error tone

sounds and you

cannot store a new

number until you

delete a record in

speed dial memory

o r t e l e p h o n e

directory.

www.vtechphones.com

17

Basic Operation

BASIC OPERATION

Speed Dialing

SPEED EDIT ERASE

8005959511

01

• If the location is

not empty, your

new entry will be

stored in place

of the old and

wi ll delete the

former entry. Take

cauti on t o n ot

save over entries

you do not wish to

delete from speed

dial memory.

5. After you enter the name, press SELECT or PROG. The screen displays ENTER NUMBER.

6. Enter the telephone number. Use to backspace and make corrections. Press REDIAL/PAUSE

to enter a pause if necessary.

— OR —

Press REDIAL/PAUSE to display the last number (up to 24 digits long) dialed from this phone.

7. Press SELECT or PROG to store your entry. The screen displays DISTINCT RING? and the

current setting.

8. Press or to choose Y (for yes) if you wish the phone to alert you to calls from this number by

assigning a distinctive ringer after the rst ring. Choose N for a normal ringer.

9. Press SELECT or PROG to conrm. If you chose Y in Step 8, a will be displayed with the

entry.

Edit a Number/Name Stored in Speed Dial

1. Press and hold the speed dial location key (1-9) of the entry you wish to edit.

2. When the screen displays the entry you want to edit, press SELECT. Then press or until EDIT

ashes.

3. Press SELECT. The screen displays the name and number. The cursor appears at the end of the

name. Use , and the dial pad keys to edit the name. Press SELECT to move on to edit the

number. Use to backspace and make corrections. Press SELECT to move on to edit the distinctive

ring setting. Press or to choose Y (for yes) if you wish the phone to alert you to calls from this

number by assigning a distinctive ringer after the rst ring. Choose N for a normal ringer.

4. Press SELECT to save the edited information.

www.vtechphones.com

18

BASIC OPERATION

Speed Dialing

Delete a Number/Name Stored in Speed Dial

1. Press and hold the speed dial location key (1-9) of the entry you wish to delete.

2. When the screen displays the entry you want to delete, press SELECT. Then press or until

ERASE ashes.

3. Press SELECT. The screen displays ERASE NO YES and the number. The current choice

ashes.

4. Press until YES ashes.

5. Press SELECT. You’ll hear a conrmation beep.

Dial a Speed Dial Number

1. Press and hold the speed dial location key (1-9) of the entry you wish to dial.

2. Press PHONE to dial the displayed memory number.

Reassign Locations in Speed Dial

1. Press and hold the speed dial location key (1-9) of the entry you wish to reassign.

2. When the screen displays the entry you want to reassign, press SELECT. Press or until

SPEED ashes.

3. Press SELECT. The screen displays ENTER 1-9.

4. Press the keys (1-9) to reassign this entry into another memory location. You’ll hear a conrmation

beep.

SPEED EDIT ERASE

8005959511

01

SPEED EDIT ERASE

8005959511

01

www.vtechphones.com

19

Basic Operation

BASIC OPERATION

Telephone Directory

Your phone can store 20 (including the nine speed dial entries) telephone numbers with names (up to

15 characters for the name and 24 digits for the number in each location) in the handset.

Store a Number/Name in the Directory

1. Press PROG. The screen displays DIRECTORY.

2. Press SELECT. The screen displays ENTER NAME.

3. Using the chart in page 16, enter up to 15 characters for the name you’re storing with the number.

Use to backspace and make corrections; use to advance and add a space.

4. When you nish entering the name, press SELECT or PROG. The screen displays ENTER

NUMBER.

5. Enter the telephone number. Use to backspace and make corrections. Press REDIAL/PAUSE to

store a pause if necessary.

— OR —

Press REDIAL/PAUSE to display the last number (up to 24 digits) dialed from this handset.

6. Press SELECT or PROG. The screen displays DISTINCT RING? and the current setting.

7. Press or to choose Y (yes) if you wish the phone to alert you to calls from this number by

changing to a distinctive ringer after the rst ring. Choose N for a normal ringer.

8. Press SELECT or PROG to conrm. If you chose Y in Step 7, a will be displayed with the directory

entry.

Edit a Number/Name Stored in the Directory

1. Press . The screen displays DIRECTORY.

2. Press or to scroll alphabetically through entries stored in directory.

— OR —

Press the dial pad key for the rst letter of the entry you want to edit.

• Press OFF at any

time to exit the

directory.

• When the memory

is full the screen will

display MEMORY

FULL, an error

tone sounds and

you will not be

able to store a

new number until

you delete a stored

number to make

room for another

entry.

www.vtechphones.com

20

BASIC OPERATION

Telephone Directory

3. When the screen displays the entry you want to edit, press SELECT. Then press or until EDIT

ashes.

4. Press SELECT. The screen displays the name and number. The cursor appears at the end of the

name. Use , and the dial pad keys to edit the name. Press SELECT to conrm and move on to

edit the number. Use to backspace and make corrections. Press SELECT to conrm and move

to edit the distinctive ring setting.

5. Press SELECT to save the edited information.

Delete a Number/Name Stored in the Directory

1. Press . The screen displays DIRECTORY.

2. Press or to scroll alphabetically through entries stored in directory.

— OR —

Press the dial pad key for the rst letter of the entry you want to delete.

3. When the screen displays the entry you want to delete, press SELECT. Then press or until

ERASE ashes.

4. Press SELECT. The screen displays ERASE NO YES and the number. The current choice

ashes.

5. Press until YES ashes.

SPEED EDIT ERASE

8005959511

SPEED EDIT ERASE

8005959511

Page is loading ...

VTech IA5874 User manual

This manual is also suitable for

VTech IA5874 User manual

Related papers

Other documents