J.W. Speaker Camera Installation guide

Brand
J.W. Speaker
Model
Camera
Type
Installation guide

This manual is also suitable for

J.W. Speaker Camera is a high-quality automotive camera designed to enhance your driving experience. With its robust construction and advanced features, it provides reliable and clear images in various lighting conditions. The camera's compact size and versatile mounting options make it suitable for a wide range of vehicles, including off-road and recreational vehicles. Whether you're navigating challenging terrains or simply want to improve your rear visibility, the J.W. Speaker Camera offers a dependable solution.

J.W. Speaker Camera is a high-quality automotive camera designed to enhance your driving experience. With its robust construction and advanced features, it provides reliable and clear images in various lighting conditions. The camera's compact size and versatile mounting options make it suitable for a wide range of vehicles, including off-road and recreational vehicles. Whether you're navigating challenging terrains or simply want to improve your rear visibility, the J.W. Speaker Camera offers a dependable solution.

INSTALLATION INSTRUCTIONS
BEFORE INSTALLATION: PRE-INSTALLATION INSTRUCTIONS:
NOTES:
To properly install this light you should have a good understanding of automotive electrical procedures and systems, and
prociency in the installation of lights. IF YOU DO NOT, PLEASE SEEK PROFESSIONAL ASSISTANCE.
PRODUCT WARRANTY:
If you have issues with a J.W. Speaker product, please
contact the authorized retailer where you purchased it.
Model Trail 6 with Camera
Parts 8001671 & 8001661
1. Read all safety notes and mounting guidelines before installing
the product. Verify that all parts listed under “In the Box” are
present and complete.
2. Inspect the product for damage. DO NOT install the product if
there is any damage. Contact the authorized retailer where you
purchased it to initiate a warranty claim if there is damage.
3. Verify that all power supply and/or charging systems comply to
the specied voltage limits for the light.
In using this guide, you agree J.W. Speaker is not responsible
for any damage, misuse, or personal injuries. This document
is intended as an educational guide only and does not make
guarantees on any nished results.
To properly install this light you should have a good understanding
of automotive electrical procedures and systems, and prociency
in the installation of lights.
IF YOU DO NOT, PLEASE SEEK PROFESSIONAL ASSISTANCE.
Rev: 06/02/2020 J.W. Speaker Corporation Germantown, WI U.S.A. www.jwspeaker.com speaker@jwspeaker.com © Copyright 2020
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
AVERTISSMENT: Cancer et effet nocif sur la reproduction - www.P65Warnings.ca.gov
Estimated Time:
Tools Needed:
Wire Functions:
In the Box:
Input Voltage:
Operating Voltage:
20 minutes
5mm Hex Key
15mm Wrench
T20 Torx Wrench
For Wiring:
Heat Gun
Wire Stripper/Crimper
Needle Nose Plier
Black = Ground
Red = Power
1. Flat Edge Trim Ring
2. Trim Ring
3. Silver Snap Ring
12V DC
9-16V DC
INSTALLATION INSTRUCTIONS:
Rev: 06/02/2020 J.W. Speaker Corporation Germantown, WI U.S.A. www.jwspeaker.com speaker@jwspeaker.com © Copyright 2020
4. Locate the arrow on the Camera label. This arrow represents the
top of the camera.
NOTE: Once the camera is snapped into the bezel, only minor
adjustments can be made to aim the camera.
5. Determine how you want the bezel mounted on the Trail 6. Next
put the camera wire through the mount and ensure the arrow (top
of the camera is facing up.
6. Ensure the arrow (top of the camera) is facing up. Snap Camera
into the bezel by applying pressure.
7. FLUSH MOUNT ONLY: Secure the camera wire by pressing it
into the wire routing channel on the bezel.
1. Remove the 6 M4 Bezel Screws from your Trail 6 if already installed
9. Place the bezel over the Trail 6. You do not need to place any
screws in at this point. Use the monitor to determine if the camera
needs any adjustments. If no adjustments are needed, proceed to
use the screws to secure the bezel to the Trail 6. If adjustments need
to be made, please proceed to step 10.
10. Locate the 2 small holes on the back of the camera.
11. Insert the tips of the needle nose pliers into the 2 small holes on
the back of the camera. Then turn only in the clockwise direction
to aim the camera.
NOTE: Turn clockwise only.
12. Repeat step 9.
3. Locate the camera inside the box. It will have 2 different trim rings.
You need to use the flat edge trim ring circled in red.
2. Remove the Outer Bezel from your Trail 6 if already installed.
8. Connect the camera to the monitor.
  • Page 1 1
  • Page 2 2

J.W. Speaker Camera Installation guide

Brand
J.W. Speaker
Model
Camera
Type
Installation guide
This manual is also suitable for

J.W. Speaker Camera is a high-quality automotive camera designed to enhance your driving experience. With its robust construction and advanced features, it provides reliable and clear images in various lighting conditions. The camera's compact size and versatile mounting options make it suitable for a wide range of vehicles, including off-road and recreational vehicles. Whether you're navigating challenging terrains or simply want to improve your rear visibility, the J.W. Speaker Camera offers a dependable solution.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents