2. Workrite Ergonomics
  3. Conform Knoll® Antenna® Adaptor
Conform Knoll® Antenna® Adaptor

Workrite Ergonomics Conform Knoll® Antenna® Adaptor Installation guide

  • Hello! I've reviewed the Assembly and Installation Instructions for the Antenna CONF-ADPT-KA-S Adaptor. This document outlines the steps for preparing your Knoll Antenna system for a monitor arm, detailing required tools and parts. I am ready to assist with your questions about the adaptor or the instructions provided.
  • What is included in the Knoll Antenna Adaptor kit?
    What tools are required for assembly?
    What should be removed from the adaptor before assembly?
1 of 2 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Phillips head screwdriver and included Allen WrenchesConform Monitor Arm
Knoll® Antenna® Table Center Beam Center Mount or
Knoll® Antenna® Table Center Beam Side Mount
A Knoll® Antenna® Adaptor
and mounting hardware
Qty: 1
Parts Included, Knoll® Antenna® Adaptor Parts Included, Hardware kit
Tools Required
Assembly & Installation Instructions:
Conform Knoll® Antenna® Adaptor CONF-ADPT-KA-S
Remove Bolt & Washers from Adaptor
Remove the M8 × 90 mm Bolt and Washers from Knoll® Antenna®
Adaptor (A).
Leave the spacer in place.
Required Parts Sold Separately
B 5 mm Allen Wrench
Qty: 1
C 4 mm Allen Wrench
Qty: 1
D 2.5 mm Allen Wrench
Qty: 1
Do not exceed rated weight limit.
M8 Flat Head Cap Screw M4 8mm Screw M4 12mm Screw M4 16mm Screw
Plastic Cap 7/32” Allen Wrench 1/8” Allen Wrench
Button Head Allen Cap ScrewPivot Pin
Steel WasherPlastic Pivot Washer
M8 Flat Head Cap Screw M4 8mm Screw M4 12mm Screw M4 16mm Screw Spacer
Plastic Cap 7/32” Allen Wrench 1/8” Allen Wrench
Button Head Allen Cap ScrewPivot Pin
Steel WasherPlastic Pivot Washer
M8 Flat Head Cap Screw M4 8mm Screw M4 12mm Screw M4 16mm Screw
Plastic Cap 7/32” Allen Wrench 1/8” Allen Wrench
Button Head Allen Cap ScrewPivot Pin
Plastic Pivot Washer
1
Articulating
Arm spacer
M8 × 90 mm Bolt
2 of 2 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Attach Knoll® Antenna® Adaptor to Center Beam
Mount and Reattach to Antenna® System
Place the Knoll® Antenna® Adaptor (A) onto the
Knoll® Center Beam Center Mount or Side Mount.
Use the bottom screw from the Knoll® Antenna®
System to affix the Center Beam Mount to the
Knoll® Antenna® Adaptor.
Use the screws supplied with Knoll® Antenna®
System to re-attach the Center Beam Mount
unit with the Knoll® Antenna® Adaptor to the
Center Beam of the Knoll® Antenna® System.
Ready for Arm Installation
You are now ready to attach your selected Conform Monitor Arm (sold separately).
Remove Knoll® Antenna® Center or Side Mount From Center Beam
If installed, remove the Knoll® Antenna® Center Beam Side Mount or
Center Mount according to manufacturer instructions. You will need
to access the bottom of the unit to attach the adaptor.
Side mount shown
1500255 Rev D
a
A
Bottom screw
Knoll® Antenna®
Center Beam
Mount
b
3
Assembled
a
b
4
2
/