LIVARNO 110474 Owner's manual

V 1.3

English ........................................................................................................................ 2

Polski ....................................................................................................................... 14

Magyar .................................................................................................................... 26

Česky ....................................................................................................................... 38

Deutsch ..................................................................................................................... 50

LIVARNO LUX LSS 520 A1

2 - English

Table of contents

Introduction ................................................................................................................ 3

Intended use ............................................................................................................... 3

Package contents ....................................................................................................... 3

Specifications ............................................................................................................. 4

Safety instructions ...................................................................................................... 5

Copyright ................................................................................................................... 6

Before start-up ........................................................................................................... 6

Proper mounting location ................................................................................................................................ 6

Required tools .................................................................................................................................................. 7

Before starting assembly ................................................................................................................................. 7

Assembly .......................................................................................................................................................... 8

Initial start-up ............................................................................................................. 9

Configuring the motion sensor ........................................................................................................................ 9

Configuring the illumination time (TIME):....................................................................................................... 9

Configuring the sensor sensitivity (SENS) ...................................................................................................... 9

Configuring the photosensitivity (LUX) ........................................................................................................... 9

Maintenance/Cleaning ............................................................................................. 10

Troubleshooting ....................................................................................................... 10

Environmental and waste disposal information ........................................................ 11

Conformity ............................................................................................................... 11

Guarantee and service ............................................................................................. 12

LIVARNO LUX LSS 520 A1

English - 3

Introduction

Thank you for choosing a LIVARNO LUX product.

Intended use

This solar LED spotlight is not intended for commercial use. It is suitable for outdoor use, in particular in

places without a mains outlet (e.g., a garage or garden shed). The built-in LED lamp provides ample

illumination. The motion sensor detects movement and automatically turns the solar LED spotlight on or off.

The device meets the requirements of all relevant standards related to CE conformity. Conformance to

these standards is no longer guaranteed if a change is made to the solar LED spotlight without the

authorisation of the manufacturer.

Package contents

Unpack the device and all accessories. Remove all packaging materials and check all parts for

completeness and for signs of damage. If any parts are missing or damaged, please contact the

manufacturer.

 Solar LED spotlight LSS 520 A1

 Solar panel

 Mounting materials for solar LED spotlight (2x large screw and 2x large dowel)

 Mounting materials for solar panel (4x small screw and 4x small dowel)

 User manual including safety instructions

This user manual contains a cover that can be unfolded. The inside of the cover provides a schematic of

the solar LED spotlight and a number legend. The numbers identify the following parts/functions:

1 Solar LED spotlight LSS 520 A1

2 On/Off switch

3 Mounting bracket

4 Arresting screw

5 Motion sensor

6 Cable (with socket)

7 Solar panel

8 Cable (with plug)

9 LUX knob

10 SENS knob

11 TIME knob

LIVARNO LUX LSS 520 A1

4 - English

Specifications

Solar LED spotlight (1):

Brand: LIVARNO LUX

Model designation: LSS 520 A1

Lamp type: LG LED: 9 x 1 W max.

LED colour temperature: 5000 K +/-500 K

Ra (colour rendering index of the LED) 80

LED light emission angle: Approx. 120°

LED service life: approx. 25,000 hrs

Max. illumination duration (fully charged

battery):

approx. 1.3 hrs

Operating voltage: 12 V (power supply via solar panel only)

Lithium-ion battery: 1,800 mAh / 7.4 V

Power consumption of entire spotlight unit 8.6 W +/-10% (given 520 lm and a fully charged

battery)

Complete power consumption of LEDs 6.0 W +/-10% (given 520 lm and a fully charged

battery)

Total luminous flux (with cover) 520 lm +/-5% (when battery is fully charged)

Protection class: IP44 (splash protection)

Dimensions (W x H x D): approx. 11.4 x 16 x 11.6 cm (incl. mounting bracket)

Weight: approx. 677 g

Solar panel (7):

Type: Polycrystalline / 3.5 W / 14.5 V

Length of connection cable: approx. 3 m

Dimensions (W x H x D): 21 x 16 x 1.6 cm (without mounting plate)

Weight (incl. mounting plate): approx. 520 g

Motion sensor (5):

Sensor detection angle: Max. 180°

Sensor range (adjustable): max. 12 m

Twilight switching level: 5 lux +/- 5 lux to 20,000 lux +/- 10 lux

LIVARNO LUX LSS 520 A1

English - 5

Swivelling (mechanically): approx. 150° horizontally / approx. 180° vertically

Illumination time (adjustable): approx. 10 sec +/- 5 sec to 4 min +/- 1 min

The specifications and design are subject to change without notice.

Safety instructions

Before using the solar LED spotlight (1) for the first time, please read the following instructions carefully

and observe all warnings, even if you are familiar with using electronic devices. Keep this user manual in

a safe place for future reference. If you give the solar LED spotlight (1) away or sell it, please ensure that

you also pass on this user manual as it is part of the device.

DANGER! This icon, together with the word ‘DANGER’, indicates an impending

dangerous situation which, if not prevented, can lead to serious injuries or even

death.

WARNING! This icon, together with the word ‘WARNING’, indicates important

information for the safe operation of the solar LED spotlight (1) and for user safety.

This icon indicates further information on the topic.

Fire hazard: Mount the solar LED spotlight (1), observing a minimum clearance of

0.5 m to materials exposed to the light. Excessive heat can cause a fire.

A shattered protective cover must be replaced.

DANGER! Keep electrical equipment out of reach of children. Also, people with reduced

mental, sensory or motor abilities should use electrical devices within the limits of their capabilities

only. Ensure that children and people with reduced mental, sensory or motor abilities never use

electrical devices unsupervised, unless they have been properly familiarised with the equipment

or are being supervised by a person in charge of their safety. Children should generally be

supervised to ensure they do not play with this device. Keep children away from the working

area when mounting the solar LED spotlight (1). The package contents include various small

parts that can result in serious injuries or even death when swallowed. Children are not always

able to identify possible threats. Therefore, also keep the packaging film away from children.

There is the risk of suffocation.

DANGER! If you notice any smoke, unusual noises or smells, immediately switch off the solar

LED spotlight (1). In these cases, you must not continue to use the device until it has been

checked by a specialist. Do not inhale smoke possibly caused by a burning device. If you

inhaled smoke, consult a physician. Inhaling smoke can be harmful to your health.

LIVARNO LUX LSS 520 A1

6 - English

DANGER! The housing of the solar LED spotlight (1) and the solar panel (7) must be free of

damage. A damaged housing can result in risk of injury.

DANGER! Do not operate the solar LED spotlight (1) in a potentially explosive atmosphere due

to the presence of combustible gases, vapours or dust, as this would result in risk of explosion.

DANGER! Never look directly into the light beam with the aid of optical instruments, such as a

magnifying lens. There is the risk of injuring your eyes. If you suspect that you may have injured

your eyes, immediately consult a physician.

WARNING! Do not attach any objects to the solar LED spotlight (1) or the

solar panel (7). The housing is not designed to carry any weights. Ignoring this warning may

result in damage to the solar LED spotlight (1) or the solar panel (7).

Copyright

All contents of these operating instructions are subject to copyright law, and are provided to the user

solely as a source of information. Any form of copying or reproduction of data and information is

prohibited without the express written permission of the author. This also concerns commercial use of the

contents and data. The text and illustrations describe the technical status at the time of printing. All

information is subject to change.

Before start-up

Remove the solar LED spotlight (1) and the mounting materials from the packaging.

Check the solar LED spotlight (1) for signs of damage. If the solar LED spotlight (1) is damaged, it must not

be put into operation.

Fully charge the built-in lithium-ion battery before initial start-up. Please make sure that the On/Off switch

(2) is set to ‘OFF’.

The duration of the charging process depends on the intensity of the solar radiation. In sunny

weather, charging takes approx. 3 days (given about 4 hours daily and approx. 60,000 lux).

Proper mounting location

Carefully choose the mounting location and thoroughly prepare for assembly.

 Systematically arrange all individual parts, required tools and mounting materials and place them

within easy reach.

 The solar LED spotlight (1) may only be mounted on a sturdy support, such as a masonry wall etc.

 Do not mount the solar LED spotlight (1) above a heat source or within direct proximity of other light

sources. Also account for Figure [D] on the cover page when selecting the mounting location.

 The built-in battery of the solar LED spotlight (1) is exclusively charged via the solar panel (7) part of

the delivery scope. The cable (8) is approx. 3 m long. Therefore, the mounting location of the solar

LIVARNO LUX LSS 520 A1

English - 7

panel (7) must be chosen such that the plug can be connected to the cable (6) socket of the solar LED

spotlight (1) without difficulty. When doing so, lay the cable (8) in a manner so it does not obstruct

people or become a tripping hazard. Ideally, mount the solar panel (7) at a bright location exposed

to direct sunlight.

 Choose a mounting location that protects the solar LED spotlight (1) from wind, rain and soiling.

 Determine in advance which mounting materials are suitable for the designated mounting location.

The solar LED spotlight (1) is delivered with mounting materials suitable for concrete.

Required tools

The package does not include the following tools. This list is provided to offer general orientation. The

precise characteristics of the required tools depend on the chosen mounting location.

 Ladder

 Spirit level, yardstick, pencil

 Drilling machine and drill

 Phillips screwdriver, flat-tip screwdriver

 Open-ended spanner, combination pliers, wire cutter

Before starting assembly

When drilling holes, ensure you do not damage any hidden cables or pipes.

Mount the device using the proper tools.

Before assembly, make yourself familiar with the individual parts of the solar LED spotlight (1) as well as

with the instructions and illustrations, and observe them during assembly.

LIVARNO LUX LSS 520 A1

8 - English

Assembly

Solar LED spotlight (1):

 Detach the mounting bracket (3) from the solar LED spotlight (1).

 Utilise the mounting bracket (3) as a template for marking the position of the two outer drill holes.

 Then drill these holes and attach the mounting bracket (3) using the supplied large dowels and

screws.

 Now attach the solar LED spotlight (1) to the mounting bracket (3) using the previously removed

screws, spring washers and flat washers. Please make sure that the spring washers are located

between the solar LED spotlight (1) and the mounting bracket (3). The flat washers must be located

between the screw head and the mounting bracket (3).

Solar panel (7):

A mounting plate with 6 drill holes for screws is located at the back of the solar panel (7).

 Mount the solar panel at the designated

location using the 4 small screws and dowels.

Depending on the topography of the mounting

location, you can freely choose 4 of the drill

holes in the mounting plate; however, you

should ideally select 2 drill holes on the right

and left each. The solar panel (7) is connected

to the mounting plate via a swivel joint. Align

the mounting plate such that you can fasten

the 4 small screws with ease.

 Then lay the cable (8) and connect the plug to

the cable (6) socket of the solar LED spotlight

(1).

 The solar panel (7) is connected to the

mounting plate via a swivel joint. Orient the

solar panel in a manner that ensures maximum

exposure to sunlight.

LIVARNO LUX LSS 520 A1

English - 9

Initial start-up

Turn on the solar LED spotlight (1) using the On/Off switch (2) by putting it into the ‘ON’ position.

Configuring the motion sensor

Ensure that no places where traffic is common (e.g., sidewalks, streets) are located within the

motion sensor’s (5) range.

When setting the photosensitivity of the motion sensor (5), you should do so at a time when the

lighting conditions configured to trigger the solar LED spotlight (1) are prevalent.

 Align the motion sensor (5) so as to ensure maximum coverage of the area to be monitored. This means

that no obstructing objects should be present in the path.

 You can change the horizontal position of the motion sensor (5) by pivoting it.

 If you wish to change the vertical alignment of the motion sensor (5), first loosen the arresting screw (4).

Once the motion sensor (5) is aligned as desired, retighten the arresting screw (4).

Configuring the illumination time (TIME):

Use the TIME knob (11) at the bottom of the motion sensor (5) to adjust the illumination time (approx.

10 sec to 4 min). Turn the TIME knob (11) clockwise (+ direction) to increase the illumination time, or turn

it counter-clockwise (- direction) to reduce the illumination time.

Please note:

In order to minimise battery consumption, set the illumination time to as short a

duration as meets your needs.

The device is preset to an illumination time of approx. one minute.

Configuring the sensor sensitivity (SENS)

Use the SENS knob (10) at the bottom of the motion sensor (5) to adjust the sensor sensitivity. Turn the

SENS knob (10) clockwise (+ direction) to increase the sensitivity, or turn it counter-clockwise (- direction)

to reduce the sensitivity. The higher the sensitivity, the larger the detection range (max. 12 metres).

Configuring the photosensitivity (LUX)

Use the LUX knob (9) at the bottom of the motion sensor (5) to adjust the photosensitivity. This setting

determines what ambient light level will trigger the twilight sensor to turn the solar LED spotlight (1) on or

off.

Turn the LUX knob (9) clockwise ( direction) to make the motion sensor (5) trigger in brighter ambient

conditions.

Turn the LUX knob (9) counter-clockwise ( direction) to make the motion sensor (5) trigger in darker

ambient conditions.

LIVARNO LUX LSS 520 A1

10 - English

Maintenance/Cleaning

Maintenance

The lamp component of the solar LED spotlight (1) comprises 9 long-life LEDs. These cannot be replaced

and thus do not require maintenance.

Cleaning

Ensure that no liquids enter the housing of the solar LED spotlight (1) as this might damage the

solar LED spotlight (1).

Clean the solar LED spotlight (1) and the solar panel

(7)

using a soft, dry cloth, and never use cleaning

agents or solvents that react with plastic. If the device is heavily soiled, slightly moisten the cloth before

cleaning.

Troubleshooting

The light does not go on

 The On/Off switch (2) is set to ‘OFF’.

 The motion sensor (5) is not properly aligned. Correct its alignment.

 The built-in battery is fully discharged. Ensure that the solar panel (7) is properly aligned, and fully

charge the battery. If necessary, shorten the illumination time to reduce the power consumption. In

order to fully charge the battery, set the On/Off switch (2) to ‘OFF’ for the duration of the charging

process. After charging is complete, switch the On/Off switch (2) back to the ‘ON’ position.

The duration of the charging process depends on the intensity of the solar radiation. In sunny

weather, charging takes approx. 3 days (given about 4 hours daily and approx. 60,000 lux).

The light goes on and off in rapid succession

 The sensor is experiencing interference caused by an external light source or bright, reflecting

surfaces. Remove the external light source or the surfaces that cause interference.

The light does not go off

 There are persons or objects in the sensor range of the motion sensor (5). Remove these.

 The solar LED spotlight (1) is swaying in the wind, causing the motion sensor (5) to trigger

continuously. Make sure the solar LED spotlight (1) is firmly attached to a sturdy surface.

LIVARNO LUX LSS 520 A1

English - 11

Environmental and waste disposal information

Devices marked with this symbol are subject to the European Directive 2012/19/EU. All

electrical and electronic equipment must not be put in the household waste, but must be

disposed of via designated public disposal centres.

By properly disposing of the old device, you can avoid environmental damage and

hazards to your health. Further information regarding proper disposal of the old device

can be obtained from your local authority or the shop where you purchased the device.

The built-in battery cannot be removed for disposal!

Make sure the packaging is disposed of in an environmentally friendly manner. Cardboard packaging

can be put out for waste-paper collection or taken to public collection points for recycling. The plastic

packaging used for your device is collected by your local waste management company and disposed of

in an environmentally sound manner.

Conformity

This device complies with the basic and other relevant requirements of the EMC

Directive 2004/108/EC, the Low-voltage Directive 2006/95/EC, the ErP Directive

2009/125/EC and the RoHS Directive 2011/65/EU. The corresponding

declaration of conformity can be found at the end of this manual.

LIVARNO LUX LSS 520 A1

12 - English

Guarantee and service

Warranty of TARGA GmbH

Dear Customer,

This device is sold with three years warranty from the date of purchase. In the event of product defects,

you have legal rights towards the seller. These statutory rights are not restricted by our warranty as

described below.

Warranty conditions

The warranty period commences upon the date of purchase. Please keep the original receipt in a safe

place as it is required as proof of purchase. If any material or manufacturing faults occur within three

years of purchase of this product, we will repair or replace the product free of charge as we deem

appropriate.

Warranty period and legal warranty rights

The warranty period is not extended in the event of a warranty claim. This also applies to replaced and

repaired parts. Any damage or defects discovered upon purchase must be reported immediately when the

product has been unpacked. Any repairs required after the warranty period will be subject to charge.

Scope of warranty

The device was carefully manufactured in compliance with stringent quality guidelines and subjected to

thorough testing before it left the works. The warranty applies to material and manufacturing faults. This

warranty does not cover product components which are subject to normal wear and which can therefore

be regarded as wearing parts, or damage to fragile components such as switches, rechargeable batteries

or components made of glass. This warranty is void if the product is damaged, incorrectly used or

serviced. To ensure correct use of the product, always comply fully with all instructions contained in the

user manual. The warnings and recommendations in the user manual regarding correct and incorrect use

and handling of the product must always be observed and complied with. The product is solely designed

for private use and is not suitable for commercial applications. The warranty is rendered void in the event

of incorrect handling and misuse, if it is subjected to force, and also if any person other than our

authorised service technicians interfere with the device. No new warranty period commences if the

product is repaired or replaced.

Submitting warranty claims

To ensure speedy handling of your complaint, please note the following:

- Before using your product for the first time, please read the enclosed documentation carefully.

Should any problems arise which cannot be solved in this way, please call our hotline.

- Always have your receipt, the product article number as well as the serial number (if available)

to hand as proof of purchase.

- If it is not possible to solve the problem on the phone, our hotline support staff will initiate further

servicing procedures depending on the fault.

LIVARNO LUX LSS 520 A1

English - 13

Service

Phone: 0207 – 36 50 744

E-Mail: [email protected]

Phone: 01 – 242 15 83

E-Mail: [email protected]

Phone: 800 – 62 175

E-Mail: [email protected]

Phone: 800 – 92 496

E-Mail: [email protected]

IAN: 110474

Manufacturer

Please note that the following address is not a service address. First contact the service point stated above.

TARGA GmbH

Coesterweg 45

59494 SOEST

GERMANY

LIVARNO LUX LSS 520 A1

14 - Polski

Spis treści

Wprowadzenie ........................................................................................................ 15

Zastosowanie zgodnie z przeznaczeniem ................................................................ 15

Zakres dostawy ....................................................................................................... 15

Dane techniczne ....................................................................................................... 16

Wskazówki bezpieczeństwa .................................................................................... 17

Prawa autorskie ...................................................................................................... 18

Przed uruchomieniem ............................................................................................... 18

Właściwe miejsce montażu ......................................................................................................................... 18

Potrzebne narzędzia .................................................................................................................................... 19

Przed montażem ........................................................................................................................................... 19

Montaż.......................................................................................................................................................... 20

Uruchomienie ........................................................................................................... 21

Ustawianie czujnika ruchu ........................................................................................................................... 21

Ustawianie czasu świecenia (TIME) ........................................................................................................... 21

Ustawianie czułości czujnika (SENS) ......................................................................................................... 21

Ustawianie czułości świetlnej (LUX) ............................................................................................................ 21

Konserwacja/czyszczenie ........................................................................................ 22

Rozwiązywanie problemów .................................................................................... 22

Informacje dotyczące ochrony środowiska i utylizacji .............................................. 23

Zgodność.................................................................................................................. 23

Informacje dotyczące gwarancji i serwisu ................................................................ 24

LIVARNO LUX LSS 520 A1

Polski - 15

Wprowadzenie

Dziękujemy za zakup produktu LIVARNO LUX.

Zastosowanie zgodnie z przeznaczeniem

Reflektor solarny LED nie jest przeznaczony do użytku komercyjnego. Nadaje się on do użytkowania na

zewnątrz, w szczególności w miejscach, w których nie ma przyłącza elektrycznego (np. garaż czy altana

ogrodowa). Wbudowany element świetlny LED zapewnia dobre oświetlenie. Czujnik rejestruje ruch

i automatycznie włącza i wyłącza reflektor solarny LED. Urządzenie spełnia wszystkie odnośne normy

i standardy związane z deklaracją zgodności CE. W przypadku modyfikowania reflektora solarnego LED

bez uzgodnienia z producentem nie gwarantuje się spełnienia tych norm.

Zakres dostawy

Wyjąć urządzenie i wszystkie akcesoria z opakowania. Usunąć materiał opakowaniowy i sprawdzić, czy

wszystkie części są kompletne i nie są uszkodzone. W przypadku braku elementów lub ich uszkodzenia

prosimy zwrócić się do producenta.

 Reflektor solarny LED LSS 520 A1

 Panel solarny

 Materiały montażowe do reflektora solarnego LED (2 x duża śruba i 2 x duży kołek)

 Materiały montażowe do panelu solarnego (4 x mała śruba i 4 x mały kołek)

 Instrukcja obsługi ze wskazówkami dotyczącymi bezpieczeństwa

Instrukcja obsługi obejmuje rozkładaną okładkę. Na wewnętrznej stronie okładki znajduje się ilustracja

reflektora solarnego LED z numerami. Numery te przypisane są do następujących elementów:

1 Reflektor solarny LED LSS 520 A1

2 Włącznik/wyłącznik

3 Uchwyt montażowy

4 Śruba ustalająca

5 Czujnik ruchu

6 Kabel (z gniazdem)

7 Panel solarny

8 Kabel (z wtyczką)

9 Pokrętło LUX

10 Pokrętło SENS

11 Pokrętło TIME

LIVARNO LUX LSS 520 A1

16 - Polski

Dane techniczne

Reflektor solarny LED (1):

Marka: LIVARNO LUX

Oznaczenie modelu: LSS 520 A1

Elementy świetlne: LG LED: 9 x 1 W maks.

Temperatura barwowa LED: 5000 K +/- 500 K

Ra (indeks odzwierciedlenia koloru LED) : 80

Kąt świecenia LED: ok. 120°

Żywotność LED: ok. 25 000 godz.

Maks. czas świecenia (przy całkowicie

naładowanym akumulatorze):

ok. 1,3 godz.

Napięcie robocze: 12 V (zasilanie tylko z panelu solarnego)

Akumulator litowo-jonowy: 1800 mAh / 7,4 V

Pobór mocy kompletnego reflektora 8,6 W +/- 10% (przy 520 lm i całkowicie

naładowanym akumulatorze)

Całkowity pobór mocy diod LED 6,0 W +/- 10% (przy 520 lm i całkowicie

naładowanym akumulatorze)

Całkowity strumień świetlny (z osłoną) 520 lm +/-5% (przy całkowicie naładowanym

akumulatorze)

Stopień ochrony: IP44 (bryzgoszczelność)

Wymiary (szer. x wys. x gł.): ok. 11,4 x 16 x 11,6 cm (z uchwytem montażowym)

Masa: ok. 677 g

Panel solarny (7):

Typ: polikrystaliczny / 3,5 W / 14,5 V

Długość kabla przyłączeniowego: ok. 3 m

Wymiary (szer. x wys. x gł.): 21 x 16 x 1,6 cm (bez płyty montażowej)

Masa (z płytą montażową): ok. 520 g

Czujnik ruchu (5):

Kąt detekcji czujnika: maks. 180°

Zasięg czujnika (regulowany): maks. 12 m

Poziom zmroku: 5 lx +/- 5 lx do 20 000 lx +/- 10 lx

LIVARNO LUX LSS 520 A1

Polski - 17

Zakres obrotu (mechaniczny): ok. 150° w poziomie / ok. 180° w pionie

Czas świecenia (regulowany) ok. 10 s +/- 5 s do 4 min +/- 1 min

Zastrzega się możliwość wprowadzenia zmian danych technicznych i wyglądu urządzenia bez

uprzedniego powiadomienia.

Wskazówki bezpieczeństwa

Przed pierwszym użyciem reflektora solarnego LED (1) należy dokładnie przeczytać poniższe instrukcje

i przestrzegać wszystkich ostrzeżeń, nawet jeśli znają Państwo zasady obchodzenia się z urządzeniami

elektrycznymi. Należy starannie przechowywać niniejszą instrukcję, aby można było sięgnąć do niej

w przyszłości. W przypadku sprzedaży lub przekazania reflektora solarnego LED (1) innej osobie należy

dołączyć do niego niniejszą instrukcję, ponieważ stanowi ona część urządzenia.

NIEBEZPIECZEŃSTWO! Ten symbol, opatrzony wskazówką

„NIEBEZPIECZEŃSTWO”, ostrzega przed niebezpieczną sytuacją, która może

prowadzić do ciężkich obrażeń lub śmierci, jeśli się jej nie zapobiegnie.

OSTRZEŻENIE! Ten symbol, opatrzony wskazówką „OSTRZEŻENIE”, wyróżnia

ważne wskazówki dotyczące bezpiecznej pracy reflektora solarnego LED (1)

i ochrony użytkownika.

Ten symbol wyróżnia dodatkowe wskazówki o charakterze informacyjnym.

Niebezpieczeństwo pożaru: Reflektor solarny LED (1) należy montować

w odległości co najmniej 0,5 m od oświetlanych materiałów. Nadmierne rozgrzanie

może prowadzić do wybuchu pożaru.

Pęknięte osłony należy wymieniać.

NIEBEZPIECZEŃSTWO! Urządzenia elektryczne nie powinny dostać się w ręce dzieci. Także

osoby upośledzone umysłowo, sensorycznie lub ruchowo powinny używać urządzeń

elektrycznych wyłącznie w ramach swoich możliwości. Nie wolno dopuścić, aby dzieci i osoby

upośledzone umysłowo, sensorycznie lub ruchowo używały urządzeń elektrycznych bez

nadzoru. Osoby takie mogą używać urządzeń elektrycznych tylko wówczas, gdy zostały

odpowiednio poinstruowane lub znajdują pod nadzorem innej osoby odpowiedzialnej za ich

bezpieczeństwo. Co do zasady dzieci powinny pozostawać pod nadzorem, aby nie bawiły się

urządzeniem. Podczas montażu reflektora solarnego LED (1) dzieci powinny przebywać z dala

od miejsca prowadzenia prac. W skład zestawu wchodzi wiele małych części, które mogą

stanowić zagrożenie dla życia w przypadku połknięcia. Dzieci nie zawsze potrafią prawidłowo

rozpoznać możliwe zagrożenia. Folie opakowaniowe należy także trzymać z dala od dzieci.

Istnieje niebezpieczeństwo uduszenia.

LIVARNO LUX LSS 520 A1

18 - Polski

NIEBEZPIECZEŃSTWO! W przypadku wykrycia dymu, nieprawidłowych odgłosów lub

zapachów, należy bezzwłocznie wyłączyć reflektor solarny LED (1). W takich przypadkach nie

wolno używać urządzenia przed przeprowadzeniem przeglądu przez fachowca. W żadnym

razie nie wdychać dymu z ewentualnego pożaru urządzenia. W przypadku zaciągnięcia się

dymem należy skonsultować się z lekarzem. Wdychanie dymu może być szkodliwe dla

zdrowia.

NIEBEZPIECZEŃSTWO! Obudowa reflektora solarnego LED (1) i panelu solarnego (7) nie

może być uszkodzona. W przypadku uszkodzonej obudowy istnieje niebezpieczeństwo

odniesienia obrażeń.

NIEBEZPIECZEŃSTWO! Nie używać reflektora solarnego LED (1) w otoczeniu grożącym

wybuchem, w którym znajdują się palne gazy, opary lub pyły. Istnieje niebezpieczeństwo

wybuchu.

NIEBEZPIECZEŃSTWO! W żadnym przypadku nie używać instrumentów optycznych, jak na

przykład szkło powiększające, by patrzeć bezpośrednio w strumień światła. Może to prowadzić

do obrażeń oczu. W przypadku podejrzenia obrażeń oczu należy natychmiast skonsultować się

z lekarzem.

OSTRZEŻENIE! Na reflektorze solarnym LED (1) lub panelu solarnym (7) nie wolno wieszać

żadnych przedmiotów. Obudowa nie nadaje się do podwieszania ciężarów. W przeciwnym

razie reflektor solarny LED (1) lub panel solarny (7) mogą ulec uszkodzeniu.

Prawa autorskie

Wszelkie treści zawarte w niniejszej instrukcji obsługi są objęte prawem autorskim i są udostępniane

czytelnikowi wyłącznie jako źródło informacji. Zabrania się kopiowania lub powielania danych

i informacji w jakiejkolwiek formie bez wyraźnej, pisemnej zgody autora. Dotyczy to również

komercyjnego wykorzystywania treści i danych. Treść i ilustracje odpowiadają stanowi technicznemu na

dzień oddania do druku. Zastrzega się możliwość wprowadzenia zmian.

Przed uruchomieniem

Wyjąć reflektor solarny LED (1) i materiały montażowe z opakowania.

Sprawdzić reflektor solarny LED (1) pod kątem uszkodzeń. W przypadku uszkodzeń nie wolno

uruchamiać reflektora solarnego LED (1).

Przed pierwszym uruchomieniem należy całkowicie naładować wbudowany akumulator litowo-jonowy.

Zwrócić uwagę, by włącznik/wyłącznik (2) znajdował się w położeniu „OFF” (WYŁĄCZONY).

Czas ładowania zależy od stopnia nasłonecznienia. Ładowanie trwa przy ładnej pogodzie

ok. 3 dni (każdorazowo po 4 godzinach i około 60 000 lx).

Właściwe miejsce montażu

Należy starannie dobrać miejsce montażu i dobrze przygotować montaż.

Page is loading ...

LIVARNO 110474 Owner's manual

LIVARNO 110474 Owner's manual

in other languages

Related papers

Other documents