Atdec AWM-LTHT Installation guide
- Category
- Flat panel desk mounts
- Type
- Installation guide
AWM-LTHT Page 1 of 3
Installation Guide
AWM-LTHT
AWM QR HD VESA Tilt Head
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! Do not remove/ throw away the black plastic sleeve on the channel clamp, arm links or arm base.
! The manufacturer accepts no responsibility for incorrect installation.
! This product is not suitable for outdoor use or mobile applications.
! Do not over-tighten screws and adjustment points on product.
! This product is compatible with AWM Series monitor arm products: AWM-AHX, AWM-LC, AWM-A46T & AWM-A71T.
! VESA mounted accessories (such as mini PC brackets and mounts), offset VESA locations, and unevenly weighted monitors
(relative to the center of the VESA mounting interface) exert additional leverage that can exceed the capacity of the mount
even though the monitor weight may be within the stated range. Please contact Atdec if you would like further information.
COMPONENT CHECKLIST
A
Heavy Duty
Tilt Head
(x1)
C
Screw
M4x10mm
(x4)
D
Security
Screw
(x1)
E
4mm
Hex Key
(x1)
B
VESA Head
(x1)
REQUIRED TOOLS
WEIGHT RANGE
Flat Monitors
0 - 18kg
(0 - 40lbs)
Curved Monitors
0 - 12kg
(0 - 26.5lbs)
• Phillips Head Screwdriver
Monitor weight should be within
the weight range of all modular
elements that make up the complete
monitor mounting solution.
AWM-LTHT Page 2 of 3
1.1 Slide release switch up
and click into unlocked
position, then remove VESA
head from the tilt head.
1.2 Check VESA mounting compatibility of monitor.
Click
Slide
100mm
75mm
100mm
75mm
NOTE: For other sizes, use a suitable adaptor plate
(sold separately).
1. Attach VESA head to monitor
1.3 Attach VESA head onto monitor with provided screws.
(Alternatively, use fasteners specied by the monitor manufacturer).
OK
Too long
Monitor
VESA Plate
VESA Screw
Too short
NOTE: Ensure screw length suits the
monitor VESA mounting holes.
2. Attach tilt head onto arm
2.1 Push tilt head onto the
shaft at the end of the
monitor arm.
2.3 Tighten the joint screw with
4mm Hex Key.
NOTE: Check the tilt
head rotation is smooth
after tightening.
2.2 Ensure tilt head is fully pushed onto shaft.
IMPORTANT! Ensure plastic
sleeve is tted on shaft before
attaching tilt head.
AWM-LTHT Page 3 of 3
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reserves the right to alter specications without notice. ©20231013
4. Adjust tilt tension
4.1 Use the knob to tighten and
loosen the tilt tension to suit
your monitor weight.
NOTE: Always support the
monitor whilst adjusting
to prevent it from falling
forward sharply.
IMPORTANT
If extra tilt
tension is
required for your
monitor, use
4mm Hex Key to
tighten second
tilt screw.
Loosen
Tighten
Loosen
Tighten
5. (OPTIONAL) Adjust rotation tension
3. Attach monitor to arm
3.1 Fit monitor onto arm.
NOTE: VESA Head
will automatically
latch onto the tilt link.
Click
3.2 OPTIONAL SECURITY SCREW
If desired, once monitor is
attached to the arm, Install the
security screw. This disables the
release switch, preventing theft.
TIGHTEN
LOOSEN
5.1 Adjust the rotation tension using 4mm Hex Key.
Adjustment may only be required for large or ultrawide monitors.
HOLDS POSITIONDRIFTS
-
1
-
2
-
3
Atdec AWM-LTHT Installation guide
- Category
- Flat panel desk mounts
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Atdec AWM-A71T Installation guide
-
-
-
-
-
-
Atdec AWM-AD Installation guide
-
-
-