Page 1 of 3
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
Please read all instructions prior to installation and keep for future reference!
1. Product to be installed by a qualied electrician.
2. Prior to installation ensure power is off at fuse box to prevent electrical shock.
DMX RGBW 3 Zone Controller - Installation Instructions
Models DMX-3Z-RGBW
7777 N. Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
REV2.6 09242020
controller
housing
pins
5
5.1 Align the back of the controller face to the controller housing
pins and snap in to secure.
123
controller face
5.1
S1 S2 S3
2.1 Carefully insert a flat screw driver into the controller housing tab
and slightly pull up until controller face comes off.
2
controller
face
tab
2.1
controller
housing
GND Vin D- D+ GND
3
junction
box 3.1
3.1 Loosen the screws on the back of the controller housing and
make all the proper wiring and then re-tighten screws. Refer to
the wiring diagram on page 2 for additional information.
controller
housing
controller
screw
GND Vin D- D+ GND
terminal connection
close up
4
junction
box
4.1 Align the controller housing to the junction box and secure using
the two screws.
controller
housing screw
4.1
1.1 Connect the white (neutral) & black (hot) power supply wires to
the white & black power wires (120 - 240VAC).
1.1
1
junction
box
120 - 240VAC
wires
controller
power supply
1.1
Note: All wires must be present in junction box (supplied by
contractor) to connect controller properly.
CONTROLLER
GND Vin D- D+ GND
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
Please read all instructions prior to installation and keep for future reference!
1. Product to be installed by a qualied electrician.
2. Prior to installation ensure power is off at fuse box to prevent electrical shock.
DMX RGBW 3 Zone Controller - Installation Instructions
Models DMX-3Z-RGBW
wiring w/ decoder
wiring w/ receiver
GND Vin D- D+ GND
CONTROLLER
SIGNAL REPEATER
POWER
SUPPLY
RGBW LINELED
RGBW LINELED
POWER SUPPLY RECEIVER
input
- +
red
- +
green
- +
blue
- +
white
- +
CONTROLLER
SIGNAL
W
B
G
R
V
W
B
G
R
V
output
24VDC
(-)
(+)
(N) (L)
output
24VDC
NOTE:
- Signal repeaters can be connected to
either beginning or end of the LineLED run.
- 1 repeater is needed every 96 watts.
NOTE:
- Signal repeaters can be connected to
either beginning or end of the LineLED run.
- 1 repeater is needed every 96 watts.
DMX cables
(For DMX cable, use
Belden 9829, 9842
or CAT5 shielded twisted
pair cabling or equivalent)
red
- +
green
- +
blue
- +
yellow
- +
input
+ -
GND
+ -
D1+ D1- D2+ D2-
DECODER
RGBW LINELED
red
- +
green
- +
blue
- +
yellow
- +
input
+ -
GND
+ -
D1+ D1- D2+ D2-
DECODER
RGBW LINELED
output
red
- +
green
- +
blue
- +
yellow
- +
input
+ -
GND
+ -
D1+ D1- D2+ D2-
DECODER
(N)
(L)
output
output
W
B
G
R
V
W
B
G
R
V
output
24VDC
SIGNAL REPEATER
POWER
SUPPLY
RGBW LINELED
RGBW LINELED
(N) (L)
AC
input
output
(-)
(+)
(N) (L)
POWER
SUPPLY
Page 2 of 3
7777 N. Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
input
120-240VAC
output
12VDC
AC
input
AC
input
AC
input
AC
input
(N)
(L)
input
120-240VAC
output
12VDC
(N)
(N)
(L)
(L)
(-)
(+)
(N) (L)
input
120-240VAC
output
12VDC
POWER
SUPPLY
REV2.6 09242020
Please read all instructions prior to installation and keep for future reference!
1. Product to be installed by a qualied electrician.
2. Prior to installation ensure power is off at fuse box to prevent electrical shock.
DMX RGBW 3 Zone Controller - Installation Instructions
Models DMX-3Z-RGBW
Controller Buttons
Operations
Page 3 of 3
7777 N. Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
REV2.6 09242020
1A. Syncing the controller to receiver
a. press the ON/OFF button.
b. press the learning button on receiver
c. then touch color wheel.
d. connected LED light will blink to confirm zone designation
e. to delete modes: press the learning button on receiver for over 5 seconds until the LED light flashes.
2A. How to save color or mode
S1, S2, S3 buttons can save a color from a mode, or it can save a color that you selected from the color wheel.
The S1, S2, S3 button, includes three default RGB colors. To replace these RGB color, press the color running button.
Select a new color, than select one of the S1, S2, S3 button and hold for 3 seconds until the light flashes. Then it
saves successfully.
. - 1B How to Set DMX Address ?
- Can control 3 zones separately or Synchronously
- Each Zone can control a DMX Decoders
All DMX Decoders In Zone 1 set as 001In Zone 2 set as 005In Zone 3 set as 009
Note: one DMX Decoder has 4 channels take 4 DMX Address, zone one take 001, 002, 003, 004: zone 2 take
005,006.007.008, zone 3 take 009. 010.011.012
Follow either Receiver (1A) or DMX decoder (1B) steps to continue.
/
