ZyXEL G-202 Owner's manual

ZyXEL G-202

802.11g Wireless USB Adapter

Quick Start Guide

Version 2.1.0

5/2008

Edition 1

CONTENTS

ENGLISH 2

DEUTSCH 14

ESPANOL 26

FRANCAIS 38

ITALIANO 50

РУССКИЙ 62

SVENSKA 74

繁體中文 86

ENGLISH

2

About Your G-202

The G-202 is a wireless network USB adapter for your

computer.

Installation Requirements

Before installation, make sure you have a computer with the

following:

• Pentium II 300MHz or above

• A minimum of 20 MB available hard disk space

• A minimum of 32 MB RAM

• A CD-ROM drive

• A USB port (with USB1.0/1.1, the G-202 can only transmit at

up to 11Mbps.)

• Windows 98 Second Edition (SE), Windows ME, Windows

2000, Windows XP or Windows Vista

• Windows 98 SE users may need the Windows 98 SE CD.

Note for Windows Vista Users: Some features in the ZyXEL

utility are not available when using Windows Vista. Please

refer to the User’s Guide for more information.

ENGLISH

3

ENGLISH

" If you have already installed Funk Odyssey

Client software on the computer, uninstall

(remove) it.

1 Installation

The installation procedures are similar for all supported

Windows versions.

" Install the ZyXEL Utility before you insert the G-

202.

1 Insert the included CD into the CD-ROM drive on your

computer. When the following screen displays, click

Setup. If the screen does not display, locate and double-

click autorun.exe.

ENGLISH

4

2 Select your language and click OK.

3 The following screen displays. Click Next.

4 Select Driver and Utility to install both ZyXEL utility and

driver on your computer. If you want to install the driver

only and use Wireless Zero Configuration (WZC) with

Windows XP, select Driver only. Click Next to accept the

default file location or click Browse to select an alternate

folder.

5

ENGLISH

5 Click Finish to restart the computer.

6 Locate an available USB port on the computer.

7 Remove the protective cap

to expose the USB

connector. Insert the G-

202 to an available USB

port on the computer. The

G-202’s lights turn on if it is

properly inserted.

" Never bend, force or twist the G-202 into the

port.

After you install the ZyXEL utility and insert the G-202, an

icon appears in the system tray (typically at the bottom of the

desktop).

If the icon color is green and/or you see the following icon

on your desktop, you are already connected to a wireless

network.

2 Connect to a Wireless Network

Using WPS

You can use Wi-Fi Protected Setup (WPS) to add your

computer to a wireless network.

ENGLISH

6

The G-202 supports two WPS methods for creating a secure

connection:

• Push Button Configuration (recommended) - create a

secure wireless network simply by clicking a button. See

section 2.2.

• PIN Configuration - create a secure wireless network by

entering the G-202’s PIN (Personal Identification Number)

into the configuration screen of an Access Point (AP). See

section 2.3.

2.1 Open the Utility

1 After you install the

ZyXEL utility and

insert the G-202, an

icon appears in the

system tray. Double-

click the icon.

7

ENGLISH

2 The ZyXEL

utility Link

Info screen

displays.

V If the icon does not display, uninstall and re-

install the ZyXEL utility. See the User’s Guide

for how to uninstall the utility.

The G-202 automatically connects to an available wireless

network without security enabled. However, this wireless

network may not be connected to the Internet.

If the icon is green you are already connected to a

wireless network.

If the icon is red, you are not connected to a wireless

network.

3 Click the Adapter tab.

ENGLISH

8

2.2 Push Button Configuration

1 Make sure that your wireless AP (Access Point) is turned

on and that it is within range of your computer.

2 In the Adapter screen, select WPS (Wi-Fi Protected

Setup) and PBC (Push Button Configuration).

3 Click Start.

4 Press the WPS button on your wireless AP (ZyXEL’s

NWA570N is shown as an example). It doesn’t matter

9

ENGLISH

which button is pressed first. You must press the second

button within two minutes of pressing the first one.

5 The AP and the G-202 establish a secure connection. This

can take up to two minutes.

6 You are now ready to connect to the Internet wirelessly

through your G-202.

Congratulations - you have finished!

2.3 WPS PIN Configuration

This section shows you how to use the WPS PIN method to

connect to an AP.

Do this only if you did not use the push-button WPS method

(see 2.2).

1 In the WPS section of the Adapter screen, select WPS

and PIN. Write down the 8-digit PIN that is displayed in

WPS

Internet

AP

G-202

ENGLISH

10

the grayed-out text field. You will need to enter this PIN in

the WPS screen of the AP.

2 Launch your AP’s configuration utility, go to the screen

where you can configure the WPS settings and enter the

G-202’s PIN (an example screen from ZyXEL’s NWA570N

is shown).

3 Click Start in the G-202 Adapter screen and Apply or

Start in the AP’s WPS screen within two minutes.

The AP authenticates the G-202 and sends the proper

configuration settings to the G-202. This may take up to two

minutes. The G-202 is now able to communicate with the AP

securely.

Congratulations - you have finished!

E

XAMPLE

11

ENGLISH

Troubleshooting

• If the lights on the G-202 are not on after you installed the

utility and the G-202, make sure the G-202 is properly

inserted.

• If the icon does not display, uninstall and re-install the util-

ity. See the User’s Guide for how to uninstall the utility.

• If your G-202 does not connect to a wireless network, make

sure there is an available wireless network within range (see

your User’s Guide for details about the site survey feature). If

wireless security is enabled for that network, you need to

configure security settings in your G-202 (see the User’s

Guide).

Note for Windows XP Users: If you want to use WZC, either

disable the ZyXEL utility (if you already installed it) or just

install the driver.

To disable the ZyXEL utility, right-click the icon and select

Exit. To activate the ZyXEL utility again, double-click the

icon on your desktop or click Start > Programs > ZyXEL G-

202 Wireless Adapter Utility > ZyXEL G-202 Wireless

Adapter Utility.

To install the driver only, select Driver only.

Important Information

Federal Communications Commission (FCC) Interference

Statement

ENGLISH

12

The 802.11g Wireless LAN Adapter has been tested to the

FCC exposure requirements (Specific Absorption Rate).

The equipment complies with FCC RF radiation exposure

limits set forth for an uncontrolled environment, under 47 CFR

2.1093 paragraph (d) (2).

This Transmitter must not be co-located or operating in

conjunction with any other antenna or transmitter.

Refer to the User's Guide for general FCC statements.

Procedure to View a Product’s Certification(s)

1 Go to www.zyxel.com.

2 Select your product from the drop-down list box on

the ZyXEL home page to go to that product's page.

3 Select the certification you wish to view from this

page.

Page is loading ...

繁體中文

86

關於您的 G-202 無線網卡

ZyXEL G-202 是用於電腦的 USB 介面無線網路卡。

設備安裝需求

在安裝之前，請確認您的電腦或筆記型電腦符合下列的需求：

• CPU Pentium II 300MHz 或以上規格

• 至少 32 MB RAM(建議64 MB)

• 至少 20 MB 可用的硬碟空間

• CD-ROM 光碟機

• 一個 USB 槽 (USB1.0/1.1 規格， G-202 傳輸最高達

11Mbps。)

• Windows 98 Second Edition, Windows ME, Windows 2000,

Windows XP 或 Windows Vista 中任一作業系統

• Windows 98 SE 的使用者可能需要 Windows 98 SE 光碟

Windows Vista 使用者請注意 : ZyXEL 公用程式有部分功能無

法在 Windows Vista 系統下使用。詳細資訊請參閱《使用手

冊》。

" 如果您的電腦先前安裝過 Funk Odyssey Client

軟體，在安裝本驅動程式前，請先移除安裝。

Page is loading ...

91

繁體中文

G-202 會自動連接可以使用但未啟用安全措施的無線網路。但

是，此無線網路可能未連接網際網路。

如果圖示呈現綠色，代表您已經連接無線網路。

如果圖示呈現紅色，代表您目前並未連接任何無線網路。

3 按一下 Adapter ( 配接器 ) 標籤。

2.2 按鈕設定

1 確認無線 AP ( 基地台 ) 已經開啟且位於電腦可接收到訊號

的範圍內。

2 在 Adapter ( 配接器 ) 畫面中，選取 WPS (Wi-Fi

Protected Setup) (WPS (Wi-Fi 保護設定 )) 和 PBC (Push

Button Configuration) (PBC ( 按鈕設定 ))。

3 按一下 Start ( 開始 )。

Page is loading ...

ZyXEL G-202 Owner's manual

ZyXEL G-202 Owner's manual

in other languages

Related papers

Other documents