Page is loading ...
PC PERFORMANCE
PCI
––
> USB2.0 Card
EDV Nr. 14052
IO 4+1USB2
05/02
Bedienungsanleitung
User`s guide
Notice d’emploi
Instrucciones de uso
Istruzioni per l’uso
Gebruiksaanwijzing
Hotline:
0180-5 40 49 10
Vivanco GmbH
Ewige Weide
D-22926 Ahrensburg/ Germany
Phone +49 (0) 4102/ 231-0
Fax +49 (0) 4102/ 231-160
Internet: www.vivanco.com
D
GB
F
I
NL
E
A c k n o w l e d g e m e n t s IBM, and OS/2 are trademarks of International Business Machines Corporation. Intel is a registered trademark of Intel Corporation. Windows is a registered trademark
of Microsoft Corporation. All other brand names and trademarks used here are trademarks of their respective owners.
PC_Perf_Manual_14052 10.05.2002 12:58 Uhr Seite 1 (Schwarz Bogen)
1716
Deutsch
PC PERFORMANCE
5. Klicken Sie "Beenden".
6. Werden im "Geräte-Manager" zwei
Einträge "NEC USB Open Host Controller"
und ein Eintrag "NEC PCI to USB Enhanced
Host Controller" angezeigt, wurde der
Treiber ordnungsgemäß installiert.
English
User`s guide
Introduction
Thank you for purchasing the Vivanco PCI –> USB2.0 Card. This 5 Port USB Card
V2.0 complies with the Universal Serial Bus Specification Revision 2.0 and Open
Host Controller interface Specification for full-/low-Speed signalling and Intel's
Enhanced Host Controller interface Specification for High-speed signalling and
works up to 480Mbps. This card fully meets PCI specification V2.2. It is fully suppor-
ted by USB operating system; such as Windows OS platform. It offers simple, fle-
xible and highly scalable connectivity between PC and full range of peripherals.
System Requirements
• IBM-Compatible PC
• Available PCI Slot
• Windows 98SE / ME / 2000 / XP
• 586/133 CPU and 32 MB RAM or Faster
Package Contents
• One High Speed 5 Port USB V2.0 Card
• User's Manual
• One CD Disk
PC_Perf_Manual_14052 10.05.2002 12:58 Uhr Seite 17 (Schwarz Bogen)
PC PERFORMANCE
1918
English
English
Installation steps:
• Turn the machine power off. Pull out the power cord.
• Open up the cover of the computer case.
• Discharge any static electricity build up in your body by touching a large gro-
unded metal surface. Avoid any contact with internal parts. Handle cards only
by their edges.
• Insert this card to the PCI slot of the main board.
• Close the computer case and reconnect all connections
Hardware Installation
Figure1: USB Controller Card Layout
Figure2: USB port
Board Location Port Name Connector Type
Cn1 ~ Cn5 USB port A 4pin A-type USB
con-nector
PIN SIGNAL
1 VCC
2DATA-
3DATA+
4 GND
USB port
(A Type)
USB Connector
Type A
Type B
Software installation
Windows
®
98SE Setup
1. Windows will auto-detect the USB Card
and display a dialog, "New Hardware
found" during system boot up. Press "Next"
on the "Add New Hardware Wizard" screen.
Note: Because of 2 OHCI and 1 EHCI Cores, system will require to install respec-
tive Driver three times. Don't be confused and follow subsequent procedures.
2. Select "Search for the best driver for your
device. (Recommended)." And click "Next".
3. Click "Next".
PC_Perf_Manual_14052 10.05.2002 12:58 Uhr Seite 19 (Schwarz Bogen)
PC PERFORMANCE
2120
English
English
4. Click "Next".
5. Click "Next".
6. Click "Finish".
7. Windows will auto-detect the USB Card
and display a dialog, "New Hardware
found" during system boot up. Press "Next"
on "Add New Hardware Wizard" of screen.
8. Select "Search for the best driver for your
device. (Recommended)." and click "Next".
9. Click "Next".
10. Click "Next".
11. Click "Next".
PC_Perf_Manual_14052 10.05.2002 12:58 Uhr Seite 21 (Schwarz Bogen)
PC PERFORMANCE
2322
English
English
12. Click "Finish".
13. Windows will auto-detect the USB Card
and display a dialog, "New Hardware
Found" during system boot up. Press
"Next" on the "Add New Hardware
Wizard" screen.
14. Select "Search for the best driver for your
device. (Recommended)." and click "Next".
15. Click "Specify a location" and insert the
"CD-disk" and click "Browse ..." to choose
CD-ROM , then click "Next" button.
16. Click "Next".
17. Click "Finish".
18. When "Device Manager" shows dual of
"NEC USB Open Host Controller" and "NEC
PCI to USB Enhanced Host Controller". It
is installed correctly.
PC_Perf_Manual_14052 10.05.2002 12:58 Uhr Seite 23 (Schwarz Bogen)
Windows
®
ME Setup
1. Windows ME supports Port (Plug-n-Play)
mode and will install the USB Card driver
auto-matically. Please insert the WinME
source CD disk, then click the "Browse "
button to choose "CD-ROM", then to click
"OK" button.
2. Windows will detect the USB Card and dis-
play a dialog, "New Hardware found" , sel-
ect "Specify the location of the driver
(Advanced)" and click "Next".
3. Select "Search for the best driver for your
device.(Recommended)" and select
"Specify a location:". Then insert the "CD-
disk" and click the "Browse " button to "CD-
ROM", then click "Next".
4. Click "Next".
PC PERFORMANCE
English
English
2524
5. Click "Finish".
6 .When "Device Manager" is shows dual of
NEC PCI to USB Open Host Controller , and
"NEC PCI to USB Enhanced Host Controller".
It is installed correctly.
PC_Perf_Manual_14052 10.05.2002 12:58 Uhr Seite 25 (Schwarz Bogen)
Windows
®
2000 Driver Installation
1. Windows 2000 supports Port (Plug-n-Play) mode and will install the USB Card
driver di-rectly.
Windows will detect the USB Card and dis-
play a dialog, "New Hardware found"
during system boot up. Press "Next" on the
"Found New Hardware Wizard" screen.
2.Select "Search for a suitable driver for my
device (recommended)", and click "Next".
3. Select "Select a loacation" and insert the
"CD-disk", then click the "Browse..." button
to choose "CD-ROM", and click "Next".
PC PERFORMANCE
English
English
2726
4. Click "Next".
5. Click "Finish".
6 .When "Device Manager" shows dual of
"NEC PCI to USB Open Host Controller" and
"NEC PCI to USB Enhanced Host Controller".
It is installed correctly.
PC_Perf_Manual_14052 10.05.2002 12:58 Uhr Seite 27 (Schwarz Bogen)
Windows
®
XP Driver Installation
1. Windows XP supports Port (Plug-n-Play) mode and will install the USB 2.0
Card driver directly.
2. Windows XP will auto-detect the USB 2.0
Card and display a dialog, "New Hardware
found" during system boot up. Press "Install
from a list or Specific location [Advanced] "
click then "Next".
3. Select "Include this location in the search"
and insert the CD disk then click the "Browse"
button to choose "CD-ROM" and click "Next".
4. Click "Continue Anyway".
PC PERFORMANCE
English
English
2928
5. Click "Finish".
6 .When "Device Manager" shows dual of
NEC PCI to USB Open Host Controller , and
"NEC PCI to USB Enhanced Host Controller",
it is installed correctly.
PC_Perf_Manual_14052 10.05.2002 12:58 Uhr Seite 29 (Schwarz Bogen)
/