MQ Multiquip LS60TD Operating instructions

OPERATION AND PARTS MANUAL

THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.

To find the latest revision of this

publication, visit our website at:

www.multiquip.com

SERIES

MODEL LS-60TD

STRUCTURAL CONCRETE PUMP

(DEUTZ BF4L914 DIESEL ENGINE)

Revision #4 (09/15/11)

PAGE 2 — MAYCO LS-60TD PUMP — OPERATION AND PARTS MANUAL — REV. #4 (09/15/11)

Proposition 65 Warning

Diesel engine exhaust and some of

LS-60TD PUMP — TABLE OF CONTENTS

MAYCO LS-60TD PUMP — OPERATION AND PARTS MANUAL — REV. #4 (09/15/11) — PAGE 3

NOTES

PAGE 4 — MAYCO LS-60TD PUMP — OPERATION AND PARTS MANUAL — REV. #4 (09/15/11)

TABLE OF CONTENTS

Specification and part number are subject to

change without notice.

MAYCO LS-60TD

STRUCTURAL CONCRETE PUMP

Proposition 65 Warning ............................................. 2

Table of Contents ...................................................... 4

Parts Ordering Procedures ...................................... 5

Specifications ............................................................ 6

Dimensions ............................................................... 7

Safety Message Alert Symbols ..............................8-9

Rules for Safe Operation ...................................10-12

Operation and Safety Decals .............................14-15

Important Hand Signals .......................................... 16

General Information ...........................................17-18

How it Works ........................................................... 19

Pump Components ............................................20-21

Control Box Components ........................................ 22

Engine Components ............................................... 23

Inspection ...........................................................24-26

Start-Up Procedure ............................................27-29

Shut-Down Procedure ............................................. 29

Operating Procedures ........................................30-36

Trailer Safety Precautions ....................................... 37

Towing Information .............................................38-39

Trailer Hitch Connections ........................................ 40

Maintenance (Pump) .........................................41-47

Maintenance (Trailer) .........................................48-50

Wiring Diagram (Tail Lights) .................................... 51

Wiring Diagram (Electrical) ..................................... 52

Wiring Diagram (Control Panel) .............................. 53

Wiring Diagram (Terminal Blocks)........................... 54

Wiring Diagram (Terminal Blocks to Comp.) ........... 55

Wiring Diagram (Harness Connect) ........................ 56

Wiring Diagram (Optional Hopper Vibrator) ............ 57

Wiring Diagram (Start/Shutdown Solenoid Relay).. 58

Hydraulic System Diagram ..................................... 59

Manifold Block Ports ............................................... 60

Appendix — Concrete Mix Information ..............61-62

Appendix — Slump Test Procedure ........................ 63

Appendix — Recommended

Shotcrete System .......................... 64-65

Appendix — Recommended

Shotcrete Accessories ...................66-67

Troubleshooting (Pump).....................................68-69

Troubleshooting (Engine) ........................................ 70

Troubleshooting (Brake System)............................. 71

Explanation Of Codes In Remarks Column ............ 72

Suggested Spare Parts ........................................... 73

COMPONENT DRACOMPONENT DRA

COMPONENT DRA

WINGSWINGS

WINGS

Name Plate and Decals ..................................... 74-75

Frame Assy. ....................................................... 76-77

Axle Assy. ........................................................... 78-79

Brake Line Assy. ................................................ 80-81

Brake Lights Assy. .............................................. 82-83

Trailer Hitch Assy. ............................................... 84-85

Battery Assy. ...................................................... 86-87

Hopper Assy. ...................................................... 88-89

Hopper Attachment Assy. .................................. 90-91

Hopper Interior Assy. ......................................... 92-93

Shuttle Cylinder Assy. ........................................ 94-97

Lubrication Pistons Assy. ................................... 98-99

Fuel Tank Assy. .............................................. 100-101

Heat Exchanger Assy. .................................... 102-103

Accumulator Assy. .......................................... 104-105

Remixer Control Assy..................................... 106-107

Lubrication Panel Assy. .................................. 108-109

Engine Cover Assy. ........................................ 110-111

Hydraulic Tank Assy. (Old Style) ..................... 112-113

Hydraulic Tank Assy. (New Style) ................... 114-115

LS-60TD Engine Assy. ................................... 116-117

LS-60TD Engine Air Cleaner Assy. ................ 118-119

Throttle Assy. ................................................. 120-121

Water Separator Assy. ................................... 122-123

Hydraulic Pump Assy. (Old Style)................... 124-125

Hydraulic Pump Assy. (New Style) ................. 126-127

Manifold Assy. ................................................ 128-129

Control Box Assy. ........................................... 130-131

Control Box Harness Assy. ............................ 132-133

Remote Control Cable Assy. .......................... 134-135

Terms and Conditions of Sale - Parts ................... 136

Mayco Pump Warranty .......................................... 137

MAYCO LS-60TD PUMP — OPERATION AND PARTS MANUAL — REV. #4 (09/15/11) — PAGE 5

www.multiquip.com

Ordering parts has never been easier!

Choose from three easy options:

WE ACCEPT ALL MAJOR CREDIT CARDS!

When ordering parts, please supply:

❒ Dealer Account Number

❒ Dealer Name and Address

❒ Shipping Address (if different than billing address)

❒ Return Fax Number

❒ Applicable Model Number

❒ Quantity, Part Number and Description of Each Part

❒ Specify Preferred Method of Shipment:

✓ UPS/Fed Ex ✓ DHL

■ Priority One ✓ Tr u c k

■ Ground

■ Next Day

■ Second/Third Day

If you have an MQ Account, to obtain a Username

and Password, E-mail us at: parts@multiquip.

com.

To obtain an MQ Account, contact you

r

District Sales Manager for more information.

Order via Internet

(Dealers Only)

:

Order parts on-line using Multiquip’s SmartEquip website!

■ View Parts Diagrams

■ Order Parts

■ Print Speciﬁcation Information

Note: Discounts Are Subject To Change

Goto www.multiquip.com and click on

Order Parts

to log in and save!

Use the internet and qualify for a 5% Discount

on Standard orders for all orders which include

complete part numbers.*

Order via Fax

(Dealers Only)

:

All customers are welcome to order parts via Fax.

Domestic (US) Customers dial:

1-800-6-PARTS-7 (800-672-7877)

Fax your order in and qualify for a 2% Discount

on Standard orders for all orders which include

complete part numbers.*

Order via Phone:

Domestic (US) Dealers Call:

1-800-427-1244

Best Deal!

International Customers should contact

their local Multiquip Representatives for

Parts Ordering information.

Non-Dealer Customers:

Contact your local Multiquip Dealer for

parts or call 800-427-1244 for help in

locating a dealer near you.

Note: Discounts Are Subject To Change

Effective:

January 1

st

, 2006

NOTICE

All orders are treated as Standard Orders and will

ship the same day if received prior to 3PM PST.

PARTS ORDERING PROCEDURES

PAGE 6 — MAYCO LS-60TD PUMP — OPERATION AND PARTS MANUAL — REV. #4 (09/15/11)

.2ELBATSNOITACIFICEPSENIGNE

ledoM

419L4FBztueD

enignEleseiD

epyT

leseiDdelooc-riA,ekorts4

srednilyCfo.oN

4

ekortSxeroB

.ni5x.ni91.4

)mm721

xmm601(

tuptuOdetaR

mpr0532@PH9.99

tnemecalpsiD

)L37.2(.ni.uc761

gnitratS

CDV21cirtcelE

yticapaCliOebuL

)sret

il5.2(.lag5.9

epyTleuF

leuFleseiD2#

yrettaB

72puorGICBV21

LS-60TD PUMP — SPECIFICATIONS

SNOITACIFICEPSPMUP.1ELBAT

ledoMDT06-SL

etaRgnipmuP*ruohrep.sdy.uc06otpU

dohteMgnipmuPnotsiPgnitacorpiceR

eziSetagerggAmumixaM )mm83(su

nim.ni2/1-1

thgieHgnipmuPlacitreV)m67(.tf052otpU

erusserPecaFnotsiPISP059

ecnatsiDgnipmuPlatnoziroH *)m503(

.tf0001

yticapaCxoBnoitacirbuLrednilyC )sretiL6.7(snollaG2

yticapaCdiulFciluardyH )sretiL981(snollaG05

yti

capaCknaTleuF)sretiL67(snollaG04

yticapaCreppoH reximerver/dwflanoitpohtiw.tf.uc01

esoHlairetaM

.aid.ni5,.

ni4,.ni3

)mm721,mm6.101,mm2.67(

ledoMenignE419L4FBleseiDobruTztueD

)sdiulfhtiw(thgieW)gk453,2(.sbl091,5

)gn

ippihs/yrd(thgieW)gk951,2(.sbl067,4

eziSeriT )mm653xmm781(.ni41x.ni53.7

snoitpO rotarbiVneercSreppoH,lortn

oCetomeRsseleriW

snotitidnocetisbojdnadesuezisenil,pmuls,ngisedximnognidnepedyravlliwtuptuoemuloV*

MAYCO LS-60TD PUMP — OPERATION AND PARTS MANUAL — REV. #4 (09/15/11) — PAGE 7

LS-60TD PUMP — DIMENSIONS

SNOISNEMID.3ELBAT

.FERSNOISNEMID

A).mc2.901(.ni34

B).mc8.634(.ni371

C).mc16(.ni42

D).mc8.771(.ni07

E).mc2.271(.ni86

Figure 1. Dimensions

PAGE 8 — MAYCO LS-60TD PUMP — OPERATION AND PARTS MANUAL — REV. #4 (09/15/11)

Safety precautions should be followed at all times when

operating this equipment. Failure to read and understand

the Safety Messages and Operating Instructions could result

in injury to yourself and others.

FOR YOUR SAFETY AND THE SAFETY OF OTHERS!

This Owner's Manual has been developed to

provide complete instructions for the safe and

efficient operation of the Multiquip Mayco

LS-60TD Structural Concrete

pump. Refer

to the engine manufacturers instructions for

data relative to its safe operation.

Before using this pump , ensure that the operating

individual has read and understands all instructions in

this manual.

SAFETY MESSAGE ALERT SYMBOLS

The three (3) Safety Messages shown below will inform you

about potential hazards that could injure you or others. The

Safety Messages specifically address the level of exposure

to the operator, and are preceded by one of three words:

DANGER, WARNING, or CAUTION.

You WILL be KILLED or SERIOUSLY injured if you

do not follow directions.

You COULD be KILLED or SERIOUSLY injured if

you do not follow directions.

You CAN be injured if you do not follow directions

HAZARD SYMBOLS

Diesel engine exhaust gases contain

poisonous carbon monoxide. This gas

is colorless and odorless, and can

cause death if inhaled. NEVER

operate this equipment in a confined

area or enclosed structure that does

not provide ample free flow air.

Potential hazards associated with operation of the pump will

be referenced with Hazard Symbols which appear throughout

this manual, and will be referenced in conjunction with Safety

Message Alert Symbols. Some examples are listed below:

Diesel fuel

is extremely flammable, and

its vapors can cause an explosion if

ignited. DO NOT start the engine near

spilled fuel or combustible fluids. DO

NOT fill the fuel tank while the engine

is running or hot.

DO NOT overfill tank, since spilled fuel could ignite if it

comes into contact with hot engine parts or sparks from

the ignition system. Store fuel in approved containers,

in well-ventilated areas and away from sparks and

flames. NEVER use fuel as a cleaning agent.

Engine components can generate

extreme heat. To prevent burns, DO NOT

touch these areas while the engine is

running or immediately after operations.

NEVER operate the engine with heat

shields or heat guards removed.

LS-60TD PUMP — SAFETY MESSAGE ALERT SYMBOLS

WARNING

DANGER

CAUTION

WARNING - LETHAL EXHAUST GASES

WARNING - BURN HAZARDS

WARNING - EXPLOSIVE FUEL

MAYCO LS-60TD PUMP — OPERATION AND PARTS MANUAL — REV. #4 (09/15/11) — PAGE 9

ALWAYS place the Engine ON/OFF

switch in the OFF position. NEVER

perform maintenance on the unit with

the ignition key in the ON position.

ALWAYS wear approved

respiratory

protection.

ALWAYS wear approved

eye

and

hearing

protection.

LS-60TD PUMP — SAFETY MESSAGE ALERT SYMBOLS

Other important messages are provided throughout

this manual to help prevent damage to your concrete

pump, other property, or the surrounding environment.

This

pump

, other property, or the surrounding

environment could be damaged if you do not

follow instructions.

NEVER tamper with the factory

settings of the engine governor or

settings. Personal injury and damage

to the engine or equipment can result

if operating in speed ranges above

maximum allowable.

CAUTION - OVER-SPEED CONDITIONS

CAUTION - ACCIDENTAL STARTING

CAUTION - RESPIRATORY HAZARDS

CAUTION - SIGHT AND HEARING HAZARDS

CAUTION - EQUIPMENT DAMAGE MESSAGES

NEVER operate equipment with covers,

or guards removed. Keep

fingers

,

hands

,

hair

and clothing away from all

moving parts to prevent injury.

WARNING - ROTATING PARTS

PAGE 10 — MAYCO LS-60TD PUMP — OPERATION AND PARTS MANUAL — REV. #4 (09/15/11)

The following safety guidelines should always be used when

operating the LS-60TD structural concrete pump:

GENERAL SAFETY

■

DO NOT operate or service this

equipment before reading this entire

manual.

■

NEVER touch the hot exhaust manifold, muffler

or cylinder. Allow these parts to cool before

servicing engine or pump.

■

High Temperatures – Allow the engine

to cool before adding fuel or performing

service and maintenance functions.

Contact with

hot!

components can

cause serious burns.

■

The engine section of this

pump requires an

adequate free flow of

cooling air.

NEVER

operate the pump in any

enclosed or narrow area

where free flow of the air

is restricted. If the air flow is restricted it will cause serious

damage to the pump or engine and may cause injury to

people. Remember the pump's engine gives off

DEADLY

carbon monoxide gas.

■

ALWAYS refuel in a well-ventilated area, away from sparks

and open flames.

■

ALWAYS use extreme caution when

working with flammable liquids. When

refueling, stop the engine and allow it to

cool.

■

NEVER

smoke

around or near the

machine. Fire or explosion could result from

fuel vapors

, or if fuel is spilled on a

hot!

engine.

■

NEVER operate the pump in an explosive atmosphere or

near combustible materials. An explosion or fire could

result causing severe

bodily harm or even death.

■

Topping-off to filler port is dangerous, as it tends to spill

fuel.

■

ALWAYS remove the

ignition key

when leaving the pump

unattended.

■

ALWAYS block the

wheels

on the unit when using on a

slope.

■

ALWAYS maintain this equipment in a safe operating

condition at all times.

■

ALWAYS stop the engine before servicing, adding fuel or

oil.

LS-60TD PUMP — RULES FOR SAFE OPERATION

■

ALWAYS check the machine for loosened threads or bolts

before starting.

■

ALWAYS wear proper

respiratory

(mask),

hearing

and

eye

protection equipment when operating the pump.

■

Whenever necessary, replace nameplate, operation and

safety decals when they become difficult read.

■

Manufacture does not assume responsibility for any

accident due to equipment modifications.

■

NEVER use accessories or attachments, which are not

recommended by Multiquip for this equipment. Damage

to the equipment and/or injury to user may result.

■

NEVER operate this equipment when not feeling

well due to fatigue, illness or taking medicine.

■

NEVER operate this equipment under the

influence or drugs or alcohol.

■

This equipment should not be

operated by persons under 18 years

of age.

■

NEVER operate this equipment without proper protective

clothing, shatterproof glasses, steel-toed boots and other

protective devices required by the job.

DANGER - READ OPERATION AND PARTS

Failure to follow instructions in this manual may lead to

serious injury or even

death!

This equipment is to be

operated by trained and qualified personnel only! This

equipment is for industrial use only.

MAYCO LS-60TD PUMP — OPERATION AND PARTS MANUAL — REV. #4 (09/15/11) — PAGE 11

■

NEVER run engine without air filter. Severe engine

damage may occur.

■

ALWAYS be sure the operator is familiar with proper safety

precautions and operation techniques before using pump.

■

ALWAYS store equipment properly when it is not being

used. Equipment should be stored in a clean, dry location

out of the reach of children.

■

DO NOT operate this equipment unless all guards and

safety devices are attached and in place.

■

CAUTION must be exercised while servicing this

equipment. Rotating and moving parts can cause injury

if contacted.

■

Keep all

inexperienced

and

unauthorized

people away

from the equipment at all times.

■

Before start-up, check the hopper and remove all foreign

matter and debris.

■

DO NOT use worn or damaged hose couplings, inspect

all hoses and couplings for wear. Replace any worn or

defective hose or couplings immediately.

■

Keep hands out of the hopper when the engine is running.

■

DO NOT disconnect hose couplings or nozzle while under

pressure. Relieve pressure by manually activating

pressure relief valve at manifold.

■

Unauthorized equipment modifications will void all

warranties.

■

Check all fasteners periodically for tightness. Also check

towing tongue bolt, lock nut and wheel lug nuts for wear.

■

Test the

pump's ON/OFF

switch. The purpose of this

test is to shut down the engine.

■

Refer to the

DEUTZ Engine Owner's Manual

for engine

technical questions or information recommended by

Multiquip for this equipment. Damage to the equipment

and or injury to user may result.

■

Always use properly rated hoses and clamps — 1500

PSI and higher.

TRANSPORTING

■

ALWAYS shutdown engine before transporting the pump.

■

Tighten fuel tank cap securely and close fuel valve to

prevent fuel from spilling.

■

Drain fuel when transporting pump over long distances

or bad roads.

Towing

■

Before towing, check the hitch and secure the safety

chain to the towing vehicle.

■

When towing, an adequate safety chain must be fastened

to the frame, refer to Towing Guidelines.

■

Tow only with a vehicle and hitch rated to pull a 6,000

lbs. load.

■

If unit is equipped with ball hitch coupler, use only 2" all

steel ball rated for minimum of 6,000 lbs. Use 1" hardened

steel pull pin, if not equipped with ball hitch.

■

This equipment shall not be towed or operated by

individuals who cannot read understand the signs, decals

or operating instructions.

■

When towing at night,

always

have rear tail lights ON.

■

DO NOT tow unit with hopper full of material.

■

DO NOT tow unit with hoses attached.

■

DO NOT tow unit in excess of 55 MPH on highways..

MAINTENANCE SAFETY

■

NEVER lubricate components or attempt service on a

running pump .

■

ALWAYS allow the pump a proper amount of time to

cool before servicing.

■

Keep the pump in proper running condition.

■

Fix damage to the pump immediately and always replace

broken parts.

■

Dispose of hazardous waste properly. Examples of

potentially hazardous waste are used motor oil, fuel and

fuel filters.

■

DO NOT use plastic containers to dispose of hazardous

waste.

LS-60TD PUMP — RULES FOR SAFE OPERATION

PAGE 12 — MAYCO LS-60TD PUMP — OPERATION AND PARTS MANUAL — REV. #4 (09/15/11)

LS-60TD PUMP — RULES FOR SAFE OPERATION

EMERGENCIES

■

ALWAYS know the location of the

nearest

fire extinguisher

.

■

ALWAYS know the location of the

nearest and

first aid kit

.

■

In emergencies

always

know the location of the

nearest phone or

keep a phone on the job site

.

Also know the phone numbers of the nearest

ambulance

,

doctor

and

fire department

. This

information will be invaluable in the case of an

emergency.

BATTERY

The battery contains acids that can cause injury to the eyes

and skin. To avoid eye irritation,

always

wear safety glasses.

Use well insulated gloves when picking up the battery. Use

the following guidelines when handling the battery:

■■

■

DO NOT drop the battery. There

is the possibility of risk that the

battery may explode.

■■

■

DO NOT expose the battery to

open flames, sparks, cigarettes

etc. The battery contains combustible gases and liquids.

If these gases and liquids come in contact with a flame or

spark, an explosion could occur.

■■

■

ALWAYS keep the battery charged. If the battery is not

charged a buildup of combustible gas will occur.

■■

■

ALWAYS keep battery charging and cables in good working

condition. Repair or replace all worn cables.

■■

■

ALWAYS recharge the battery in an vented air

environment, to avoid risk of a dangerous concentration

of combustible gases.

■■

■

In case the battery liquid (dilute sulfuric acid) comes in

contact with

clothing or skin

, rinse skin or clothing

immediately with plenty of water.

■■

■

In case the battery liquid (dilute sulfuric acid) comes in

contact with your eyes, rinse eyes immediately with plenty

of water, then contact the nearest doctor or hospital, and

seek medical attention.

MAYCO LS-60TD PUMP — OPERATION AND PARTS MANUAL — REV. #4 (09/15/11) — PAGE 13

NOTE PAGE

PAGE 14 — MAYCO LS-60TD PUMP — OPERATION AND PARTS MANUAL — REV. #4 (09/15/11)

LS-60TD PUMP — OPERATION AND SAFETY DECALS

Machine Safety Decals

The LS-60TD structural concrete pump is equipped with a number of safety decals. These decals are provided for operator safety

and maintenance information. Figure 2 below illustrates these decals as they appear on the machine. Should any of these decals

become unreadable, replacements can be obtained from your dealer.

Figure 2. LS-60TD Operation and Safety Decals

MAYCO LS-60TD PUMP — OPERATION AND PARTS MANUAL — REV. #4 (09/15/11) — PAGE 15

LS-60TD PUMP — OPERATION AND SAFETY DECALS

Figure 2. LS-60TD Operation and Safety Decals (Continued)

PAGE 16 — MAYCO LS-60TD PUMP — OPERATION AND PARTS MANUAL — REV. #4 (09/15/11)

LS-60TD PUMP — IMPORTANT HAND SIGNALS

Figure 3 Operation Hand Signals

Figure 3 display's the basic hand signals commonly used in concrete pumping operations.

MAYCO LS-60TD PUMP — OPERATION AND PARTS MANUAL — REV. #4 (09/15/11) — PAGE 17

CONCRETE MIX DESIGN

Mix design is most important to achieve maximum pumpability.

Pumpability is affected by, among other factors, the type and

gradation of aggregate used. Natural aggregates make a more

workable mix and pump more readily than crushed aggregates.

A blend of natural and crushed aggregates will produce a

workable mix. The type and gradation of aggregates is equally

important for workability as the size and percentage of coarse

aggregates in the mix.

The term “aggregates” describes all of the solid materials, from

the largest rock to the smallest grain of sand, contained in the

concrete mix.

Concrete mixes with a consistency as dry as one-inch slump

and as wet as ten-inch slump have been pumped; but for

maximum efficiency from the pump, a slump ranging from two to

six inches will produce a more workable mix than one that

contains more or less water.

The principle of concrete pumping is based on self-lubrication.

As it moves through the transfer line, the concrete takes the

shape of a plastic cylinder. It is forced through the transfer line on

a film of mortar that is self-troweled to the service of the transfer

line around its full periphery by the slug of concrete itself.

A slump rating should be used with discretion; it is not always a

real indication of the pumpability of the mix. The concrete may

be workable in the sense that it will readily flow into place, but

the same mix may not respond to pressure. Overly wet mixes

tend to separate. In addition to affecting the strength and quality

of the concrete, the delivery system will not tolerate separation.

Overly dry mixes are similarly unsatisfactory if they lack plasticity

and tend to be crumbly. To be properly pumped, the mix must be

able to continuously coat the inside of the line with a lubricating

seal of mortar.

LS-60TD PUMP — GENERAL INFORMATION

There are four ways in which this seal can be lost:

1. By pumping excessively wet mixes which do not have

enough cohesion to hold together.

2. By pumping harsh undersanded concrete with poorly graded

aggregates which can jam together when the pressure

becomes too great for the insufficient amount of sand to

hold the aggregates apart.

3. By getting a rock pocket, such as mixer tailings, into the

pump valve. This rock pocket will have an insufficient coating

of mortar and the mix will not be plastic enough to allow the

valve to operate or the mix to move in the line.

4. Through excessive bleeding. If the mix is short or fines, but

the sand is otherwise fairly well graded, bleeding will not

normally create any problems as long as the pump continues

operation. But, if the pump is shut down, bleeding can result

in a loss of lubrication and blocked erratic flow.

The above are bad concrete practices, regardless of how the

mix is to be placed. But, these points do show that special mixes

are not always needed, within limits, for pumping concrete. Good

aggregate gradation is most important to pump concrete the

maximum distance.

The use of admixtures can have a beneficial effect on pumpability.

Most of the dispersing agents will fatten, retard bleeding, and

increase workability. Thus, the average concrete can be pumped

for appreciably longer distances. Air entraining agents will also

improve workability, although they cannot be used as a substitute

for good gradation of the aggregate. Pumping will not appreciably

affect the final air content of the mix. High-early cement tends to

give a more readily pumpable mix with superior water retaining

qualities. However, if delays are likely to occur, extra care must

be exercised due to the faster setting time over regular cement.

The Mayco LS-60TD models will pump a wide variety of concrete

pump mixes. But, there are guidelines that must be followed.

Use this information in conjunction with the

Operating

Procedures

section of this manual.

PAGE 18 — MAYCO LS-60TD PUMP — OPERATION AND PARTS MANUAL — REV. #4 (09/15/11)

LS-60TD PUMP — GENERAL INFORMATION

REGIONAL DIFFERENCES

Concrete is made by mixing locally available rock and sand with

cement and water. For this reason there are great differences in

the pumpability of concrete from one region of the country to

another.

It is impossible to define a specific mix for each region that the

concrete pump be will working in. Therefore, the mixes listed in

Appendix - Concrete Mix Information will provide a basic

guideline for establishing the proper mix design for your area.

Use this information to specify your requirements to your local

ready-mix batch plant, contractor and civil engineer. It may take

minor adjustments to make a mix pumpable, so you should

explain your needs.

The elements that have to be controlled and consistently

maintained by the batch plant are:

1. The sizing and mix percentage of rocks, gap graded from

the largest down through the smallest sizes.

2. Sand with a sieve analysis that has the proper percentage

of fines, ASTM C33 spec.

3. Sufficient cement to produce the required design strength

of the concrete and provide the lubricating binder to pump

the concrete through the delivery system.

Use a minimum of:

500 lbs. of cement/cu yd for 2500 p.s.i. concrete after 28

days.

530 lbs. of cement/cu yd for 3000 p.s.i. concrete after 28

days.

600 lbs. of cement/cu yd for 4000 p.s.i. concrete after 28

days.

4. Admixture pump-aid if necessary.

5. The proper amount of water to make a workable slump and

plasticize the mix.

In addition, this Mayco Structural Concrete Pump can be used to

pump a large aggregate hard rock as follows:

1. Pea rock (1/2" minus) pump with mixes being as low as 30%

rock and 70% sand. (See page 44, for comments on cleaning

the pump.)

2. Shortening pea rock when used with an air compressor

and nozzle. (See back pages for recommended set-up.)

3. “Mud Jacking”, high pressure grouting.

MAYCO LS-60TD PUMP — OPERATION AND PARTS MANUAL — REV. #4 (09/15/11) — PAGE 19

LS-60TD PUMP — HOW IT WORKS

The following is a brief explanation of how the concrete cylinders,

hydraulic cylinders, shuttle tube, valves and hopper work in

sequence to pump concrete.

The hydraulic pressure is generated by a variable volume,

pressure compensated, axial piston pump that is driven by a

diesel engine. The rod sides of the drive cylinders are

hydraulically connected together creating a “slave circuit,” which

allows hydraulic oil to transfer from one piston to the other.

The two part cycling sequence is initiated by an electrical signal

generated by two proximity switches located in the drive cylinder.

The proximity switches are normally open, magnetically sensing

the movement of the main drive cylinder. As the drive cylinder

piston head passes the proximity switch, an electrical signal is

sent to the solenoid operated pilot valve which in turn directs

pilot oil to the four valves controlling the drive cylinder and the

shuttle cylinder.

A one-gallon accumulator assists the movement of the shuttle

tube. This circuit assures that the shuttle tube will throw with the

same intensity of each stroke regardless of how fast the main

drive cylinders are cycling.

Figure 4. Pumping Cycle 1

TO TANK

HIGH PRESSURE

OIL FROM PUMP

PROXIMITY

SWITCH

HYDRAULIC

CYLINDERS

PISTON

CUP

CONCRETE

CYLINDERS

SHUTTLE TUBE

SLAVE

OIL

SHUTTLE TUBE MOTION

A

B

In the first cycle, hydraulic pressure is applied to cylinder (B),

causing the hydraulic piston, which is connected to the concrete

piston and piston cup, to discharge concrete into the delivery

line (Figure 4).

As one cylinder is discharging concrete, the hydraulic oil from

the rod side (B) of the drive cylinders is being transferred through

the slave circuit causing the opposite cylinder (A) to move back

on the suction stroke, filling the cylinder with concrete.

The shuttle tube is sequenced to pivot to each concrete cylinder

as the drive cylinders stroke to push concrete. As the second

cycling sequence begins (Figure 5), the shuttle tube pivots to

the opposite cylinder (A). The hydraulic piston passes under the

proximity switch and sends pressure to the piston, causing it to

stroke and discharge concrete into the delivery line. Hydraulic

oil is transfered through the slave circuit to cylinder B, causing it

to start a suction stroke, refilling it with concrete. The pumping

sequence then repeats for the durration of the operation.

Figure 5. Pumping Cycle 2

PAGE 20 — MAYCO LS-60TD PUMP — OPERATION AND PARTS MANUAL — REV. #4 (09/15/11)

Figure 6 illustrates the location of the major components for

the LS-60TD Structural Concrete Pump. The function of each

component is described below:

1. Tow Hitch Coupler – Requires a 2-inch ball hitch or a

3-inch pintle. Capable of towing 6,000 lbs.

2. Documentation Box – Contains engine and pump

operation, parts and maintenance information.

3. Manifold Access Door– Turn handle and lift door to

access the Hydraulic Manifold Block.

4. Hydraulic Manifold Block – Aluminum block that

controls the flow of hydraulic pressure to the

components required to control the pump.

5. Hopper Discharge Sleeve – Connect hoses or steel

pipes to the discharge sleeve for pouring concrete.

6. Pump End Jack Stand – Use this jack stand to level

and support the rear end of the pump. NEVER deploy

on un-level ground and always check for firmness of

ground.

7. Shuttle Cylinder – Under pressure, the shuttle cylinder

shears concrete passing from the concrete cylinder to

the delivery line durring the cycle phase.

LS-60TD PUMP — PUMP COMPONENTS

Figure 6. Major Pump Components

Page is loading ...

MQ Multiquip LS60TD Operating instructions

MQ Multiquip LS60TD Operating instructions

Related papers

Other documents