Peerless SF630P and assembly Specification

Features:

• For 10" - 24" (25 - 61 cm) ﬂ at panel screens

• Ultra-slim design holds the screen ﬂ at against the wall

Installation and Assembly:

Universal Flat Wall Mount for 10" - 24" (25 - 61 cm) LCD Flat

Panel Screens

Models: SF630P, SF630P-S, SF630, SF630-S

ISSUED: 04-18-05 SHEET #: 201-9427-7 04-20-10

Max UL Load Capacity: 80 lb (36.3 kg)

©

U

L

USC

I

D

:

0

1

8

7

6

2

2 of 23

ISSUED: 04-18-05 SHEET #: 201-9427-7 04-20-10

Table of Contents

Parts List.................................................................................................................................................................................3

Installation to Single Wood Stud Wall .....................................................................................................................................4

Installation to Solid Concrete or Cinder Block ........................................................................................................................5

Attaching Mounting Plate to Screen with VESA Mounting Patterns .......................................................................................6

Installing and Removing Flat Panel Screen............................................................................................................................7

NOTE: Read entire instruction sheet before you start installation and assembly.

Tools Needed for Assembly

• stud ﬁ nder ("edge to edge" stud ﬁ nder is recommended)

• phillips screwdriver

• drill

• 5/16" (8 mm) bit for concrete and cinder block wall

• 5/32" (4 mm) bit for wood stud wall

• level

• Do not begin to install your Peerless product until you have read and understood the instructions and warnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US

customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact

your local distributor.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

• Never exceed the Maximum UL Load Capacity. See page one.

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of

an "edge to edge" stud ﬁ nder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws ﬁ rmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding

power.

• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal

injury.

• This product was designed to be installed on the following wall construction only;

WALL CONSTRUCTION HARDWARE REQUIRED

• Wood Stud Included

• Wood Beam Included

• Solid Concrete Included

• Cinder Block Included

• Metal Stud Do not attach except with Peerless Metal Stud Accessory Kit - ACC215

(not evaluated by UL);

• Brick Contact Qualiﬁ ed Professional (not evaluated by UL)

• Other or unsure? Contact Qualiﬁ ed Professional (not evaluated by UL)

WARNING

3 of 23

ISSUED: 04-18-05 SHEET #: 201-9427-7 04-20-10

GHFEC

I

D

SF 630P SF 630P-S

SF 630 SF 630-S

Description Qty Part # Part # Part # Part #

A

wall plate 1 095-1320 095-4320 095-1320 095-4320

B hook bracket 1 095-1321 095-4321 095-1321 095-4321

C M5 x 12 mm screw 2 520-1027 520-1027 520-1064 520-1064

D M4 x 10 mm phillips screw 4 504-9012 504-9012 504-9012 504-9012

E M4 x 20 mm phillips screw 4 504-9020 504-9020 504-9020 504-9020

F retaining spacer 4 590-5005 590-5005 590-5005 590-5005

G #14 x 2.5" wood screw 2 5S1-015-C03 5S1-015-C03 5S1-015-C03 5S1-015-C03

H concrete anchor 2 590-0320 590-0320 590-0320 590-0320

I 4 mm security allen wrench 1

--

560-1145 560-1145

Parts List

A

B

Before you begin, make sure all parts shown are included with your product.

Parts may appear slightly different than illustrated.

4 of 23

ISSUED: 04-18-05 SHEET #: 201-9427-7 04-20-10

Installation to Single Wood Stud Wall

Use a stud ﬁ nder to locate the edges of the stud. Use of an edge-to-edge stud ﬁ nder is highly recommended.

Based on its edges, draw a vertical line down the stud’s center. Place wall plate (A) on wall as a template, making

sure that the two mounting holes are over the stud centerline. Level plate, and mark the center of the two holes.

Drill two 5/32" (4 mm) dia. holes 2.5" (64 mm) deep. Make sure that the wall plate is level, secure it using

two #14 x 2.5" wood screws (G) as shown.

Skip to step 2.

G

A

1

• Installer must verify that the supporting surface will safely support the combined load of the equipment and all

attached hardware and components.

• Tighten wood screws so that wall plate is ﬁ rmly attached, but do not overtighten. Overtightening can damage the

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud ﬁ nder

is highly recommended.

• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs.

Installers are responsible to provide hardware for other types of mounting situations (not evaluated by UL).

WARNING

5 of 23

ISSUED: 04-18-05 SHEET #: 201-9427-7 04-20-10

Make sure that wall plate (A) is level, use it as a

template to mark two mounting holes. Drill two 5/16"

(8 mm) dia. holes to a minimum depth of 2.5"

(64 mm). Insert anchors (H) in holes ﬂ ush with wall

as shown (right). Place wall plate over anchors and

secure with two #14 x 2.5" screws (G). Level, then

tighten all fasteners.

1

Installation to Solid Concrete or Cinder Block

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" (35 mm) of actual

concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount

in a solid part of the block, generally 1" (25 mm) minimum from the side of the block. Cinder block must meet ASTM

C-90 speciﬁ cations. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a

hammer drill to avoid breaking out the back of the hole when entering a void or cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Make sure that the wall will safely support four times the combined load of the equipment and all attached hardware

and components.

WARNING

• Tighten screws so that wall plate is ﬁ rmly attached,

but do not overtighten. Overtightening can damage

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Always attach concrete expansion anchors directly

to load-bearing concrete.

• Never attach concrete expansion anchors to

concrete covered with plaster, drywall, or other

ﬁ nishing material. If mounting to concrete surfaces

covered with a ﬁ nishing surface is unavoidable (not

evaluated by UL), the ﬁ nishing surface must be

counterbored as shown below. Be sure concrete

anchors do not pull away from concrete when

tightening screws. If plaster/drywall is thicker than

5/8" (16 mm), custom fasteners must be supplied by

installer (not evaluated by UL).

WARNING

G

CINDER BLOCK

SOLID

CONCRETE

A

H

1

3

2

H

Drill holes and insert anchors (H).

Place plate (A) over anchors (H) and secure with screws (G).

Tighten all fasteners.

A

H

G

concrete

surface

CUTAWAY VIEW

INCORRECT CORRECT

wall

plate

wall

plate

plaster/

dry wall

plaster/

dry wall

concrete

6 of 23

ISSUED: 04-18-05 SHEET #: 201-9427-7 04-20-10

Attaching Hook Bracket to Flat Panel Screen Using VESA 75 and 100 mm

mounting patterns

Thread M5 phillips screws (C) to hook bracket (B)

making the screws ﬂ ush with bracket as shown in

ﬁ gures 2.1 and 2.2.

2

B

C

B

ﬁ g. 2.1 ﬁ g. 2.2

D

FOR VESA 100 MOUNTING PATTERN:

Choose hole pattern as shown below. Attach hook

bracket (B) to back of screen using four M4 x 10

mm screws (D) as shown below.

D

FOR VESA 75 MOUNTING PATTERN:

Choose hole pattern as shown below. Attach hook

bracket (B) to back of screen using four M4 x 10 mm

screws (D) as shown below.

*Note: If hole pattern is in a pocket, attach hook

bracket (B) to back of screen using four M4 x 20 mm

screws (E) and four spacers (F) as indicated below.

B

5

*For screens with a

hole pattern in a pocket,

spacers (F) go between

adapter plate (B) and

screen.

F

• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly

secured, damage may occur to screen or product may fail.

WARNING

7 of 23

ISSUED: 04-18-05 SHEET #: 201-9427-7 04-20-10

Hook screen onto wall plate (A) ﬁ gure 6.1. Tighten

M5 x 12 mm screws (C), shown in ﬁ gure 6.2 and

detail 1.

Note: For security models, use 4 mm security allen

wrench (I) to tighten M5 x 12 mm screws (C).

To remove screen from mount, loosen screws (C)

and lift screen off of mount.

Installing and Removing Flat Panel Screen

6

A

SCREEN

• Do not tighten screws with excessive force.

Overtightening can cause damage to mount. Tighten

screws to 20 in. • lb (2.26 N.M.) maximum torque.

CAUTION

• Do not lift more weight than you can handle. Use ad-

ditional man power or mechanical lifting equipment

to safely handle placement of the screen.

• Failure to lock hook bracket with screws (C) can

cause screen to come off mount if hit accidentally.

WARNING

DETAIL 1

ﬁ g. 6.2

ﬁ g. 6.1

A

C

B

A

C

All other brand and product names are trademarks or registered trademarks of their respective owners.

Peerless Industries, Inc.

3215 W. North Ave.

Melrose Park, IL 60160

www.peerlessmounts.com

Page is loading ...

22 of 23

ISSUED: 04-18-05 SHEET #: 201-9427-7 04-20-10

Español

Peerless Industries, Inc. establishes a warranty period of ﬁ ve years for products manufactured or supplied by Peerless. This period commences from the date of

sale of the product to the original consumer, but will in no case last for more than six years after the date of the product’s manufacture. During the warranty period

such products will be free from defects in material and workmanship, provided they are installed and used in compliance with the instructions established by

Peerless Industries, Inc. Subject to applicable legal requirements, during the warranty period Peerless will repair or replace, or refund the purchase price of, any

such product which fails to conform with this warranty.

Any other warranties prescribed by the law which may apply with respect to such products also are limited in duration to the warranty period speciﬁ ed in this

Limited Five-Year Warranty.

This warranty does not cover damage caused by (a) service or repairs by the customer or a person who is not authorized for such service or repairs by Peerless

Industries, Inc., (b) the failure to utilize proper packing when returning the product, (c) incorrect installation or the failure to follow Peerless’ instructions or warnings

when installing, using or storing the product, or (d) misuse or accident, in transit or otherwise, including in cases of third party actions and force majeure.

In no event shall Peerless be liable for incidental or consequential damages or damages arising from the theft of any product, whether or not secured by a security

device which may be included with the product.

This Limited Five-Year Warranty is in lieu of all other warranties, expressed or implied, and is the sole remedy with respect to product defects. No retailer, dealer,

distributor, installer or other person is authorized to modify or extend this warranty or impose any obligation on Peerless in connection with the sale of any product

manufactured or supplied by Peerless.

This warranty gives speciﬁ c legal rights, and you may also have other rights provided by the national legislation of the country in which you purchased such

product.

LIMITED FIVE-YEAR WARRANTY

www.peerlessmounts.com

Peerless Industries, Inc., offre une garantie de cinq ans sur les produits fabriqués ou fournis par ses soins. Cette période commence à la date de vente du

produit au client d’origine, mais ne peut en aucun cas dépasser de plus de six ans la date de fabrication. Pendant la période de garantie, les produits couverts

seront exempts de tout défaut matériel et de main d’œuvre, dès lors qu’ils sont installés et utilisés dans le respect des instructions de Peerless Industries, Inc.

Conformément aux dispositions légales applicables, Peerless réparera ou remplacera, ou remboursera le prix d’achat de tout produit non conforme à cette

garantie pendant cette période.

Toute autre garantie obligatoire applicable à ces produits est également limitée à la durée spéciﬁ ée dans la présente Garantie de cinq ans.

Cette garantie ne couvre pas les dommages causés par (a) les interventions ou les réparations effectuées par le client ou par une personne non agréée par

Peerless Industries, Inc., (b) la non-utilisation de l’emballage approprié lors du renvoi du produit, (c) une installation incorrecte ou le non-respect des instructions

ou des avertissements de Peerless lors de l’installation, de l’utilisation ou du rangement du produit, ou (d) une mauvaise utilisation ou un accident pendant le

transport ou en toute autre circonstance, y compris du fait de tiers et en cas de force majeure.

Peerless ne saura en aucun cas être tenue pour responsable de tout préjudice accidentel ou induit, ou de tout préjudice dû au vol d’un produit, qu’il soit ou non

protégé par un dispositif de sécurité éventuellement fourni avec le produit.

Cette garantie de cinq ans remplace et annule toute autre garantie, expresse ou implicite, et constitue le seul recours valable en cas de dysfonctionnement

des produits. Aucun détaillant, revendeur, distributeur, installateur ou autre n’est autorisé à modiﬁ er ou à prolonger cette garantie, ou à imposer une obligation

quelconque à Peerless lors de la vente de produits fabriqués ou fournis par Peerless.

Cette garantie confère certains droits spéciﬁ ques, mais d’autres droits peuvent vous être conférés par la législation du pays où vous avez acheté le produit.

GARANTIE DE CINQ ANS

www.peerlessmounts.com

Page is loading ...

Peerless SF630P and assembly Specification

This manual is also suitable for

Peerless SF630P and assembly Specification

in other languages

Related papers

Other documents