CYBEX Juno-Fix is a booster seat with backrest, headrest, and adjustable safety cushion, designed to provide maximum protection and comfort for children aged approximately 9 months to 4 years, weighing 9 to 18 kg.
CYBEX Juno-Fix is a booster seat with backrest, headrest, and adjustable safety cushion, designed to provide maximum protection and comfort for children aged approximately 9 months to 4 years, weighing 9 to 18 kg.
C111_056-7_01A
CYBEX GmbH
Riedinger Str. 18 | 95448 Bayreuth | Germany
WWW.CYBEX-ONLINE.COM
WWW.FACEBOOK.COM/CYBEX.ONLINE
GO TO WWW.CYBEX-ONLINE.COM
TO WATCH AN INSTRUCTIONAL VIDEO
ECE R-44/04 Gr. 1, 9-18 kg (ca. 9M - 4Y)
JUNO-FIX
usER GuidE
ENMY
Page is loading ...
WARNING! THIS SHORT MANUAL SERVES AS AN OVERVIEW ONLY. FOR MAXIMUM PROTECTION AND BEST
COMFORT OF YOUR CHILD, IT IS ESSENTIAL TO READ AND FOLLOW THE ENTIRE INSTRUCTION MANUAL
CAREFULLY.
4 | CONTENT
AMARAN! MANUAL RINGKAS INI BERTUJUAN UNTUK GAMBARAN KESELURUHAN SAHAJA. ADALAH MENJADI
KEMESTIAN UNTUK MERUJUK DAN MEMATUHI KESELURUHAN MANUAL ARAHAN DENGAN TELITI BAGI
KESELAMATAN OPTIMA DAN PERLINDUNGAN MAKSIMUM UNTUK ANAK ANDA.
5 | KANDUNGAN
3
EN
MY
CYBEX JUNO-FIX
Kerusi penggalak dengan sandaran belakang,
sandaran kepala dan kusyen keselamatan mudah ubah
DISYORKAN UNTUK:
Umur: dari 9 bulan hingga 4 tahun
Berat: 9-18 kg
Untuk kerusi kenderaan yang dilengkapi tali pinggang
perenggang automatic tiga penjuru, selaras dengan
ECE R16
PERAKUAN:
ECE R44/04, Kumpulan 1, 9 - 18 kg
CYBEX JUNO-FIX
Booster seat with backrest, headrest and adjustable
safety cushion
RECOMMENDED FOR:
Age: from approx. 9 months to 4 years
Weight: 9 - 18 kg
For vehicle seats with three-point automatic retractor
belt according to ECE R16
HOMOLOGATION:
ECE R44/04, Group 1, 9 - 18 kg
03/2013
THANK YOU FOR PURCHASING THE CYBEX JUNO-FIX. WE ASSURE YOU THAT
IN THE PROCESS OF DEVELOPING THE CYBEX JUNO-FIX WE FOCUSED ON
SAFETY, COMFORT AND FUNCTIONALITY. THE PRODUCT IS MANUFACTURED
UNDER SPECIAL QUALITY SURVEILLANCE AND COMPLIES WITH THE
STRICTEST SAFETY REQUIREMENTS.
SHORT MANUAL ...........................................................................................................................2
HOMOLOGATION ...........................................................................................................................4
FIRST INSTALLATION ....................................................................................................................6
ADJUSTING TO THE BODY SIZE ...............................................................................................8
THE BEST POSITION IN THE CAR ...........................................................................................10
INSTALLATION OF THE CHILD SEAT WITH ISOFIX CONNECT SYSTEM ....................12
RELEASING THE ISOFIX CONNECTORS .............................................................................14
PLACING THE CHILD SEAT IN THE CAR ............................................................................... 14
SITTING AND RECLINING POSITION ............................................................................. 16 - 18
ADJUSTING THE SAFETY CUSHION .....................................................................................18
SECURING THE CHILD ...............................................................................................................20
IS YOUR CHILD PROPERLY SECURED? ...............................................................................20
PRODUCT CARE ..........................................................................................................................22
CLEANING ......................................................................................................................................22
REMOVING THE SEAT COVER ................................................................................................22
WHAT TO DO AFTER AN ACCIDENT ......................................................................................24
DURABILITY OF THE PRODUCT .............................................................................................24
DISPOSAL ......................................................................................................................................24
WARRANTY ...................................................................................................................................26
CONTENT
DEAR CUSTOMER
4
Page is loading ...
L.S.P.
WARNING! For your child’s maximum protection, it is essential to use and install
the child seat according to the instructions in this User Guide.
!
WARNING! The components of the CYBEX child seat must not be used either on
their own or in combination with seat cushions, backrests or headrests from other
manufacturers or other model ranges. In any such cases the child seat will no
longer be certied for use.
!
WARNING! Always ensure that the individual components of the child seat are
never compressed or jammed (e.g. by the car door or while adjusting the back
seat.)
!
Note! Please keep the User Guide handy in the slot under the cover at the back of the
backrest.
The child seat consists of a seat cushion (d) and a backrest (a) with a headrest
(e), which adjusts to suit the child‘s height, as well as a safety cushion (p), which is
adjustable for depth. Your child will benefit from maximum protection and comfort only
when all components are used together.
The backrest (a) is hooked onto the axis (c) of the seat cushion (d) by means of the
guide lug (b). Push the two side protectors provided with the „Linear Side-impact
Protection“ System (L.S.P.) into the installation holes (z) provided for this purpose, on
the outer edges of the shoulder brackets. These will lock into place with an audible
„CLICK“.
Note! Please always keep the User Guide in the slot provided for it under the seat
cover, on the back of the backrest.
FIRST INSTALLATION
b
a
a
c
e
p
z
d
6
Page is loading ...
Use the adjustable headrest (e) to adjust the seat to the child‘s height. Only when
the headrest (e) is adjusted to the optimum height does it offer maximum protection
and comfort to the child. There are 8 possible positions for adjusting the height of the
headrest. It should be adjusted so that there is a space of two fingers‘ width between
the lower edge of the headrest and the child‘s shoulder. To adjust the headrest (e)
release the adjustment handle (h) by pulling it. The adjustment handle (h) is located
on the underside of the headrest (e). Push the headrest into the required position. As
soon as you release the adjustment handle (h) the headrest (e) automatically locks into
place.
ADJUSTING TO THE CHILD’S HEIGHT
e
h
8
Page is loading ...
There is a „semi-universal“ homologation for securing the child seat with ISOFIX
connectors. For this reason the CYBEX JUNO-fix with ISOFIX CONNECT
system may be installed only in certain types of cars. Please see the details
of authorised vehicles and positions on the enclosed list of approved cars. A
constantly updated list of authorised cars can be found on
www.cybex-online.com. Items of luggage and other loose objects in the car, which
could cause injury in an accident, must always be safely secured. Such items and
objects can become deadly projectiles inside the car.
Note! Never leave your child unattended in the car.
THE BEST POSITION IN THE CAR
The CYBEX JUNO-fix can be used without the ISOFIX CONNECT system on
all seats with a three-point automatic belt. However, we generally recommend
that you install the child seat on the rear seat behind the front passenger. There
is greater danger in most accidents of injury to your child, if the child seat is installed
on the middle rear passenger seat. In exceptional cases, however, the child seat can
be used on the front passenger seat. Please note the following points:
w
• In cars with front airbags the passenger seat must be pushed as far back as
possible.
• It is imperative that you comply with the car manufacturer‘s recommendations.
WARNING! The child seat is not suitable for use with 2-point or lap belts. If you
are involved in an accident and the seat is secured with a 2-point seat belt, the
child may be severely injured or killed.
!
WARNING! The child seat must not be used on vehicle seats which are installed
at right angles to the direction of travel. On rear-facing seats in vehicles, as for
example, in a van or minibus, use of the child seat is authorised, provided that the
vehicle seat is authorised for the carriage of an adult. It is essential to ensure that
the headrest is not removed when the child seat is installed in a rearward-facing
direction. The child seat must always be secured in place with the vehicle seat
belt, even when not in use. If you have to perform an emergency stop or if you
are involved in a minor collision an unsecured child seat can injure you and other
passengers.
!
10
Page is loading ...
• Activate the handle (v) on the underside of the child seat.
• Pull out the ISOFIX connectors (w) as far as possible.
• Turn the connectors 180°, so that they show in the direction of the ISOFIX
GUIDES (u).
• Push the two ISOFIX connectors (w) into the GUIDES (u) until they lock into
place on the anchorage points (i) with an audible „CLICK“.
• Make certain that the child seat is securely fixed in place by trying to pull it out.
• The green safety indicator (x) must be clearly visible on both red release
buttons (y).
• You can now use the handle (v) on the underside of the child seat to adjust the
position of the seat.
• You can now secure your child in the child seat; see „SECURING THE CHILD“
x
y
If it is difficult to access the ISOFIX anchorage points (i) of your car, and to protect the
seat cover you can permanently fit the ISOFIX guides (u) provided in both anchorage
points. In many cars it is more effective to install the ISOFIX guides (u) in an opposing
direction.
INSTALLATION OF THE CHILD SEAT WITH ISOFIX
CONNECT SYSTEM
With the ISOFIX CONNECT System you can secure the child seat safely in
the car and thus make your child safer. Your child is further protected by the
security of your car‘s three-point automatic seat belt.
u
w
x
y
u
w
v
i
Note! The ISOFIX anchorage points (i) are two metal rings per seat and are located
between the backrest and the seat of the car. If you are in any doubt, consult your
car’s instruction manual for assistance.
Note! Take care that the two green safety indicators (x) on the ISOFIX connectors (w)
are not visible. If necessary, release the connectors (w) by pressing and pulling back
the red release button (y). Repeat the process as appropriate for the second connector
Note! Please refer to the section „PLACING THE CHILD SEAT IN THE CAR“.
To secure the CYBEX JUNO-fix correctly, observe the following instructions:
12
Page is loading ...
PLACING THE CHILD SEAT IN THE CAR
• Place the child seat on the appropriate seat in the car.
• To install the seat in an upright position for the child it is essential
to take care that the backrest (a) of the child seat lies flush against
backrest of the car seat. To achieve this, push the seat toward the car
seat backrest.
• By using the ISOFIX anchorage points (i) in the car, you can adjust this
distance with the handle (v) on the underside of the child seat.
• If the headrests of the car seats get in the way, pull these completely
out, turn them round, or detach them completely (exception see section
„THE BEST POSITION IN THE CAR“). The backrest (a) adjusts itself in
one movement to almost every position of the car seat.
RELEASING THE ISOFIX CONNECTORS
Note! Retracting the connectors not only protects the car seat, but also protects the
ISOFIX CONNECT system from dirt and damage.
Note! Some car seat covers made from delicate materials (e.g. velour, leather etc.)
may be marked by the use of child seats. This can be avoided by placing a blanket or
a towel beneath the child seat.
y
x
a
w
v
• Release the ISOFIX connectors (w) on both sides, by pressing and
pulling back the red release buttons (y).
• Pull the seat out of the ISOFIX guides (u).
• Turn the ISOFIX connectors (w) 180°.
• Activate the handle (v) on the underside of the child seat and push the
connectors in until they reach the end position.
Carry out the installation steps in reverse order.
WARNING! The CYBEX JUNO- x backrest must lie fl ush with the back of the car
seat. In order to guarantee maximum protection for the child, the seat must be
in a normal, upright position. (exception see section „SITTING AND RECLINING
POSITION“)
!
14
Page is loading ...
Note! The maximum safe and permissible reclining position is limited by the edge of
the seat of the car seat. The child seat must not extend beyond this limit! If the CYBEX
JUNO-fix backrest loses contact with the car seat or if the seat cushion (d) rises away
from the seat of the car seat, the maximum position has been exceeded and must be
corrected.
Note! If the CYBEX JUNO-fix is used without ISOFIX CONNECT, putting the child seat
in the reclining position is prohibited!
• Now you can continue with the section “SECURING THE CHILD“
• When you have taken the child out of the car seat and want to return the seat
from the reclining to the sitting position, activate the handle (v) again and apply
slight pressure to the seat cushion (d) to guide the child seat back into the
upright position.
• Install the seat as described in the section, „INSTALLATION OF THE CHILD
SEAT WITH ISOFIX CONNECT“.
• To adjust the reclining position, activate the handle (v) on the underside of the
seat cushion (d) and pull the connectors out as far as the end stop.
SITTING AND RECLINING POSITION
In order to adjust the child seat reclining position the car seat belt must be released.
The reclining position can only be adjusted by using the ISOFIX CONNECT
system.
w
v
d
WARNING! Always ensure that the handle (v) locks into the reclining and sitting
positions with an audible click.
!
16
Page is loading ...
Activating both adjustment handles (q) simultaneously causes the safety cushion (p) to
glide automatically into its furthest forward position. Releasing the adjustment handles
(q) fixes the safety cushion (p) in place. The side parts of the safety cushion (p) fit
exactly into the arm rests of the seat cushion (d) and provide support for the seat.
Adjust the safety cushion (p) so that it lies against the child‘s chest without excerting
any pressure on the childs body.
ADJUSTING THE SAFETY CUSHION
d
p
q
WARNING! The safety cushion (p) must be used only with the seat and only for
children weighing not more than 18 kg.
!
18
Page is loading ...
• Put the child in the child seat.
• Put the previously adjusted safety cushion (p) in place (see section
„ADJUSTING THE SAFETY CUSHION“)
• Draw out the three-point automatic belt to its fullest extent. Take the lap belt (n)
and insert it into the belt routing marked in red (r) of the safety cushion (p).
• Push the belt tongue (m) into the belt buckle (l). This must lock into place with
an audible „CLICK“.
• Pre-tension the lap belt (n) by pulling on the shoulder belt (f).
• Now guide the shoulder belt (f) back through the belt routing (r) of the safety
cushion (p).
• Pull the shoulder belt (f) taut, taking care that both parts of the belt run over the
total width of the safety cushion (p), within the belt routing (r).
• the safety cushion (p) is correctly adjusted.
• the belt tongue (m) has locked into place in the belt buckle (l).
• the lap belt (n) and the shoulder belt (f) are running taut through the belt routing
of the safety cushion (p) and are not twisted.
• the seat cushion (d), when ISOFIX Connect is used, has locked into place on
both sides with the connectors (w) into the ISOFIX anchorage points (i) and
both green safety indications (x) can be seen clearly.
• the backrest (a) of the child seat lies completely flush with the backrest of the
car seat. (Exception see section, „SITTING AND RECLINING POSITION“).
SECURING THE CHILD
To guarantee the maximum safety for your child, please test the following before
departure:
m
n
n
r
f
l
IS YOUR CHILD PROPERLY SECURED?
WARNING! Do not twist the belt!
!
20
Page is loading ...
REMOVING THE SEAT COVER
• Once the press-studs on the back of the backrest have been undone, the cover
can be removed by drawing it forwards.
• To remove the seat cushion cover, release both belt straps and also undo the
press-studs on the underside and draw the cover forward.
• The headrest cover can simply be pulled forward to remove it.
• All visible parts of the child seat must be regularly checked for damage. The
mechanical parts must function faultlessly.
• It is essential to make sure that the child seat is not jammed between hard
parts such as the car door, seat rails etc., which can damage it.
• If the child seat is dropped it must be tested by the manufacturer before being
used again.
PRODUCT CARE
CLEANING
Care must be taken that only an Original CYBEX Seat Cover is used, because the
cover is also a fundamental component of the good functioning of the child seat.
Replacement covers may be obtained from a specialist shop.
Note! Please wash the cover before using it for the first time. The cover should be
washed at 30 °C in a delicate wash cycle. Washing it at temperatures higher than 30
°C may result in the colours running. Wash separately from other items and never dry
in the tumble dryer! Never dry in strong sunlight! The plastic parts can be cleaned with
a mild cleaning agent.
To guarantee that your child seat provides the maximum protection, it is essential to
comply with the following points:
The cover consists of three main components for headrest, backrest and seat cushion,
which are secured to the child seat either by velcro, press-studs or elastic bands. Once
you have released all the fastenings, you can remove the individual components for
washing.
To detach the individual components of the cover carry out the following steps:
To replace the cover, carry out the same steps in the reverse order.
WARNING! Never use chemical cleaning or bleaching agents!
!
22
Page is loading ...
At the end of the life of the child safety seat, it must be disposed of properly. Waste
disposal regulations may vary from region to region. In order to guarantee proper
disposal, please contact your local waste management office or your local council.
Please be sure to observe the waste disposal regulations in your country.
The child seat is designed to fulfil its purpose for its expected service life of up to 4
years. However, since cars can be exposed to high fluctuations in temperature and
unforeseeable stresses, please take note of the following points:
DISPOSAL
If you are involved in a collision, the seat may sustain damage that is not visible to the
naked eye. If this is the case, the child seat must be examined by the manufacturer
and replaced if necessary.
WHAT TO DO AFTER AN ACCIDENT
• If the car is exposed to direct sunlight for a longer period of time, the child seat
must be taken out of the car or covered with a cloth.
• Examine all plastic and metal parts of the seat for any damage or changes to
their shape or colour at least once a year. Should you notice any changes, the
child seat should either be discarded or examined by the manufacturer and
replaced if necessary.
• Changes to the fabric in general and fading colours in particular are normal
after long periods of use in a car and do not constitute a fault.
DURABILITY OF THE PRODUCT
24
Page is loading ...
CYBEX GmbH,
Riedinger Str. 18, 95448 Bayreuth, Germany
Tel.: +49 921 78511-0, Fax.: +49 921 78511- 999
CONTACT
The following warranty applies solely in the country where this product was initially
sold by a retailer to a customer. The warranty covers all manufacturing and material
defects, existing and appearing, at the date of purchase or appearing within a term
of three (3) years from the date of purchase from the retailer who initially sold the
product to a consumer (manufacturer’s warranty). In the event that a manufacturing
or material defect should appear, we will – at our own discretion – either repair the
product free of charge or replace it with a new product. To obtain such warranty it is
required to take or ship the product to the retailer, who initially sold this product to a
customer and to submit an original proof of purchase (sales receipt or invoice) that
contains the date of purchase, the name of the retailer and the type designation of this
product. This warranty shall not apply in the event that this product is taken or shipped
to the manufacturer or any other person other than the retailer who initially sold this
product to a consumer. Please check the product with respect to completeness and
manufacturing or material defects immediately at the date of purchase or, in the
event that the product was purchased in distance selling, immediately after receipt. In
case of a defect stop using the product and take or ship it immediately to the retailer
who initially sold it. In a warranty case the product has to be returned in a clean and
complete condition. Prior to contacting the retailer, please read this instruction manual
carefully. This warranty does not cover any damages caused by misuse, environmental
influence (water, fire, road accidents etc.) or normal wear and tear. It does solely apply
in the event that the use of the product was always in compliance with the operating
instructions, if any and all modifications and services were performed by authorized
persons and if original components and accessories were used. This warranty does
not exclude, limit or otherwise affect any statutory consumer rights, including claims in
tort and claims with respect to a breach of contract, which the buyer may have against
the seller or the manufacturer of the product.
WARRANTY
26
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
CYBEX Juno-Fix is a booster seat with backrest, headrest, and adjustable safety cushion, designed to provide maximum protection and comfort for children aged approximately 9 months to 4 years, weighing 9 to 18 kg.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Crown Automotive SC30121 Installation guide
-
IKEA MATMÄSSIG Important information
-
mothercare iZi Up X3 Fix User manual
-
-
Silver Cross Discover Car Seat User manual
-
BESAFE Download user manual User manual
-
Yowza JUNO Owner's manual
-
Hernik IPAI-NXT User manual
-
CONCORD ABSORBER XT Owner's manual
-
CONCORD air.safe Owner's manual
