LT-Z32/26SX5 / LCT1869-001A-H / All Cover
Cover01
WIDE LCD PANEL TV
INSTRUCTIONS
LT-Z32SX5
LT-Z26SX5
ENGLISH
LCT1869-001A-H
LCT1869-001A-H_Cover.fm Page 1 Thursday, May 19, 2005 4:17 PM
LT-Z32/26SX5 / LCT1869-002A / All Cover
Cover02
LT-Z32&26SX5_Eng.book Page 2 Wednesday, May 18, 2005 5:54 PM
1
ENGLISH
LT-Z32/26SX5 / LCT1869-002A / English
Thank you for buying this JVC LCD flat television.
To make sure you understand how to use your new TV, please read this manual thoroughly before you
begin. (“LCD” stands for Liquid Crystal Display.)
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
WARNING
• Fingers may be trapped under the TV causing injuries.
Hold the TV at the bottom in the middle, and do not
allow it to tilt up or down.
WARNING
• The TV may fall causing injuries. Hold the bottom of the
stand with your hand and tilt the TV up and down.
• Do not allow children to hang from the TV, place their
elbows on the TV or lean against the TV. Doing so may
cause the TV to fall over and lead to injuries.
CAUTION
• The TV screen may be damaged if the TV is carried as
shown in the diagram below.
The TV should always be carried by two people.
LT-Z32&26SX5_Eng.book Page 1 Wednesday, May 18, 2005 5:54 PM
2
LT-Z32/26SX5 / LCT1869-002A / English
ENGLISH
Failure to take the following precautions may cause damage to the television
or remote control.
DO NOT block the TV’s ventilation openings or holes.
(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be
able to get out.)
DO NOT place anything on top of the TV.
(such as cosmetics or medicines, flower vases, potted plants, cups, etc.)
DO NOT allow objects or liquid into the cabinet openings.
(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)
DO NOT place any naked flame sources, such as lighted candles, on the TV.
DO NOT subject the TV to direct sunlight.
Pixel defects
LCDs use collections of fine points (“pixels”) to display images. While there is no problem with
more than 99.99% of these pixels, please understand that a very small number of pixels may not
light, or may light all the time.
Distance recommendations
Avoid improper installation and never position the unit
where good ventilation is impossible.
When installing this TV, distance recommendations
must be maintained between the set and the wall, as well
as inside a tightly enclosed area or piece of furniture.
Keep to the minimum distance guidelines shown for
safe operation.
The surface of the TV screen is easily damaged. Be very careful with it when handling the TV.
Should the TV screen become soiled, wipe it with a soft dry cloth. Never rub it forcefully.
Never use any cleaner or detergent on it.
If there is a fault, unplug the unit and call a service technician. Do not attempt to repair it yourself
or remove the rear cover.
200 mm 200 mm
50 mm
150 mm 150 mm
LT-Z32&26SX5_Eng.book Page 2 Wednesday, May 18, 2005 5:54 PM
3
ENGLISH
LT-Z32/26SX5 / LCT1869-002A / English
Cleaning the screen
The screen is coated with a special thin film to reduce reflection. If this film is damaged, uneven
colours, discolouration, scratches, and other problems that cannot be repaired may occur. Pay
attention to the following when handling the screen.
• Do not use glue or adhesive tape on the screen.
• Do not write on the screen.
• Do not allow the screen to come in contact with any hard objects.
• Do not allow condensation to form on the screen.
• Do not use alcohol, thinner, benzene or other solvents on the screen.
• Do not rub the screen hard.
CAUTION:
• Operate only from the power source specified (AC 110 – 240 V, 50/60 Hz) on the unit.
• Avoid damaging the AC plug and power cord.
• When you are not using this unit for a long period of time, it is recommended that you disconnect
the power cord from the main outlet.
D.I.S.T. demonstration
To start the D.I.S.T. demonstration:
Press the H button to display the menu bar. Then press the yellow button.
A picture split in two (D.I.S.T. turned on and D.I.S.T. turned off) will appear on the screen.
To quit the D.I.S.T. demonstration:
Press the yellow button, b button, 6 p buttons or any of the number buttons.
LT-Z32&26SX5_Eng.book Page 3 Wednesday, May 18, 2005 5:54 PM
4
LT-Z32/26SX5 / LCT1869-002A / English
ENGLISH
CONTENTS
Setting up your TV ...................................5
Installation.................................................. 5
Using the stand .......................................... 5
Removing the terminal covers ................... 6
Connecting the aerial and video cassette
recorder (VCR) ....................................... 7
Connecting the power cord to the AC
outlet....................................................... 8
Putting the batteries into the remote
control..................................................... 8
Initial settings (Setup tour) ......................... 8
TV buttons and functions......................10
Turn the TV on from standby mode ......... 10
Choose a TV channel .............................. 10
Adjust the volume .................................... 10
Using the Menu........................................ 10
Using the Illumination............................... 10
Remote control buttons and
functions..............................................11
Turn the TV on or off from standby mode
... 11
Choose a TV channel and watch images
from external devices ........................... 12
Adjust the volume .................................... 13
Display function........................................ 13
ZOOM function......................................... 14
CINEMA SURROUND function................ 15
Using the “Freeze” function...................... 15
Using the “Multi-picture” function ............. 16
RETURN PLUS function and Return
function................................................. 17
Favourite channel function....................... 18
Operating a JVC brand DVD player......... 19
Teletext function ....................................20
Basic operation ........................................ 20
Using the List Mode ................................. 20
Hold.......................................................... 21
Sub-page ................................................. 21
Reveal...................................................... 21
Size .......................................................... 21
Index ........................................................ 22
Cancel...................................................... 22
Using the TV’s menu..............................23
Basic operation ........................................ 23
PICTURE menu ...................................... 25
PICTURE MODE...................................... 25
BACK LIGHT............................................ 25
CONTRAST ............................................. 25
BRIGHT.................................................... 25
SHARP..................................................... 25
COLOUR.................................................. 25
TINT ......................................................... 25
WHITE BALANCE.................................... 25
FEATURES .............................................. 26
SOUND menu ......................................... 29
STEREO / I • II ......................................... 29
BASS........................................................ 29
TREBLE ................................................... 29
BALANCE ................................................ 29
CINEMA SURROUND ............................. 29
A.H.B. (Active Hyper Bass) ...................... 29
BBE .......................................................... 30
FEATURES menu................................... 31
SLEEP TIMER ......................................... 31
CHANNEL GUARD .................................. 31
APPEARANCE......................................... 33
BLUE BACK ............................................. 33
CHILD LOCK............................................ 33
AUTO SHUTOFF ..................................... 33
FAVOURITE SETTING ............................ 33
ILLUMINATION ........................................ 34
SET UP menu ......................................... 35
AUTO PROGRAM.................................... 35
EDIT/MANUAL ......................................... 35
LANGUAGE ............................................. 39
VIDEO-1 SETTING/VIDEO-3 SETTING .. 39
AI VOLUME.............................................. 39
TELETEXT LANGUAGE .......................... 40
HDMI SETTING ....................................... 40
Displaying a computer screen.............. 41
Connecting to the computer ..................... 41
Watching images from a computer .......... 41
Table of signals for each type of
computer............................................... 41
Additional preparation .......................... 42
Connecting external equipment ............... 42
Using the HDMI terminal .......................... 45
CH/CC numbers ..................................... 47
Troubleshooting .................................... 48
Specifications ........................................ 50
LT-Z32&26SX5_Eng.book Page 4 Wednesday, May 18, 2005 5:54 PM
5
ENGLISH
LT-Z32/26SX5 / LCT1869-002A / English
Setting up your TV
• When you install the TV on the wall, only use a JVC wall mounting unit (optional) which is
designed for this TV.
• Make sure that the TV is installed on the wall by a skilled installer.
Installation
Cautions for installation
• Install the TV in a corner on a wall or on the floor so as to keep cords out of the way.
• The TV will generate a slight amount of heat during operation. Ensure that sufficient space is
available around the TV to allow satisfactory cooling. See “Distance recommendations” on
page 2.
Using the stand
This TV comes with a table top stand already attached.
This stand can be used to adjust the direction of the TV screen 5° up, 10° down, and 20° to the left
or right.
Tilt the TV up and down:
While holding the bottom of the stand with one
hand, use your other hand to hold the middle of
the top of the TV and slowly tilt the TV up and
down.
• As a safety measure, the stand is
constructed so that it requires a certain
amount of force to tilt the TV.
Rotate the TV to the left and right:
While holding the bottom of the stand with one
hand, use your other hand to hold the edge of
the panel and slowly adjust the direction of the
TV screen.
LT-Z32&26SX5_Eng.book Page 5 Wednesday, May 18, 2005 5:54 PM
6
Setting up your TV
LT-Z32/26SX5 / LCT1869-002A / English
ENGLISH
Removing the terminal covers
There are connection terminals behind the covers on the left and right of the rear of the TV.
Remove these two covers before connecting an antenna or VCR.
• Leave the covers off if they do not fit properly. Do not force to replace the covers. Doing so
may cause damage to the connection cables and the covers.
Cable holder
A cable holder which is used to keep the
connection cables tidy is attached to the back
of the stand. Gently squeeze the left and right
of the cable holder and pull it to remove it from
the stand. After putting the cables in the cable
holder, attach it to the back of the stand again.
Remove the covers by removing the hooks.
When replacing the covers, place the side of
the covers against the TV and insert the hooks.
cable holder
LT-Z32&26SX5_Eng.book Page 6 Wednesday, May 18, 2005 5:54 PM
Setting up your TV
7
ENGLISH
LT-Z32/26SX5 / LCT1869-002A / English
Connecting the aerial and
video cassette recorder (VCR)
Caution
• Turn off all the equipment including the
TV before connecting anything.
• Aerial cable is not supplied. Use a good
quality 75-ohm coaxial cable.
• Read the manual that came with the VCR
before connecting.
If not connecting a VCR (follow 1):
Connect an aerial cable to the aerial
socket on this TV.
If connecting a VCR:
1 Connect the aerial cable to the
aerial input socket on the VCR, and
connect the VCR and TV with
another aerial cable
2 Connect the VCR’s VIDEO OUT
(video output) terminal and the
TV’s VIDEO terminal with a video
cable
To connect a VCR to the TV with an S-
VIDEO cable:
Connect the VCR’s S-VIDEO OUT (S-
VIDEO output) terminal and TV’s S
VIDEO terminal with an S-VIDEO cable
A, instead of connecting with a video
cable.
Note that the connection with a video
cable will be ignored in case you connect
a VCR to the TV with both video cable
and S-VIDEO cable.
3 Connect the VCR’s VIDEO OUT
(audio L/R output) terminals and
the TV’s AUDIO terminals with an
audio cable
• To connect additional external devices,
please see “Connecting external
equipment” on page 42.
1
1
23
IN
(ANALOG)
L
R
IN (HDMI AUDIO)
IN
(A
NALO
G)
IN(H
D
M
I AU
D
IO
)
without terminal covers
LT-Z32&26SX5_Eng.book Page 7 Wednesday, May 18, 2005 5:54 PM
8
Setting up your TV
LT-Z32/26SX5 / LCT1869-002A / English
ENGLISH
Connecting the power cord to
the AC outlet
Insert the AC plug on the power cord from
the TV into AC outlet.
Caution
• Operate only from the power source
specified (AC 110 – 240 V, 50/60 Hz)
on the unit.
• Remove the AC plug from the outlet to
completely disconnect the TV from the
power supply.
Putting the batteries into the
remote control
Use two AA/R6 dry cell batteries.
Insert the batteries from the - end, making
sure the + and - polarities are correct.
• Follow the warnings printed on the
batteries.
• Battery life is about six months to one
year, depending on how much you use the
remote control.
• The batteries we supply are only for
setting up and testing your TV, please
replace them as soon as you need to.
• If the remote control does not work
properly, replace the batteries.
Initial settings (Setup tour)
When the TV is first turned on, it goes into
the initial settings mode, and you will see the
JVC logo. Follow the instructions on the
screen display to make the initial settings.
1 Make sure to set the PIP/TV/DVD
switch on the remote control to the
TV position
• You cannot turn the TV on when the
PIP/TV/DVD switch is set to the DVD
position.
2 Press the # button on the remote
control
The TV turns on from standby mode and
the JVC logo is displayed.
• Check that the AC plug on the power
cord from the TV is connected to AC
outlet.
6
buttons
# button
PIP/TV/DVD
switch
POWER PROGRAM/TIMER
Remote control
sensor
Power lamp Illumination
lamp
LT-Z32&26SX5_Eng.book Page 8 Wednesday, May 18, 2005 5:54 PM
Setting up your TV
9
ENGLISH
LT-Z32/26SX5 / LCT1869-002A / English
• If the JVC logo does not appear this is
because your TV has already been
turned on for the first time:
use the “LANGUAGE”, “TELETEXT
LANGUAGE” and “AUTO
PROGRAM” functions to make the
initial settings. For details, see “SET
UP menu” on page 35.
3 Press the a button
The LANGUAGE menu appears.
4 Press the 6 buttons to choose
ENGLISH. Then press the a
button
The TELETEXT LANGUAGE menu
appears. Set the teletext language group
that corresponds to the language of the
teletext programme that you want to watch.
For details, see “TELETEXT
LANGUAGE” on page 40.
5 Press the 6 buttons to choose a
group. Then press the a button
The AUTO PROGRAM function starts.
The TV channels you receive are
automatically stored in the programme
numbers (PR) list.
• To stop the AUTO PROGRAM
function, press the a button.
6 After the TV channels have been
registered in the programme
numbers (PR), the EDIT menu
appears
• You can proceed to edit the
programme numbers (PR) list using
the EDIT/MANUAL function. For
details, see “EDIT/MANUAL” on
page 35.
• If a TV channel you want to view is
not stored in the programme numbers
(PR) list, you can register it using the
MANUAL function. For details, see
“EDIT/MANUAL” on page 35.
• The AUTO PROGRAM function does
not store a TV channel to the
programme number PR 0 (AV).
• If you do not need to use the EDIT/
MANUAL function, press the a
button to close the EDIT menu.
Now, setting up is complete. Please
enjoy your new JVC TV!
D1003
OK
GROUP-1
> TELETEXT LANGUAGE
GROUP-2
GROUP-3
GROUP-4
-EN
CH
>>
14%
D0004
OK
28
AUTO PROGRAM
-EN
>
PR ID
AV
21
22
23
24
25
26
D0038
OK
DELETE
MANUAL
ID
MOVE
INSERT
CC
CC
CC
01
02
03
CH
CH
CH
CH
CH
CH
CH/CC
EDIT
02
03
05
04
06
07
08
09
01
-EN
LT-Z32&26SX5_Eng.book Page 9 Wednesday, May 18, 2005 5:54 PM
10
LT-Z32/26SX5 / LCT1869-002A / English
ENGLISH
TV buttons and functions
Refer to the pages in parentheses for details.
1 Remote control sensor
2 Power lamp (page 8)
3 Illumination lamp (page 34)
4 TV/VIDEO button
5 MENU/OK button (page 23)
6 CHANNEL p buttons
6 (page 23)
7 VOLUME q buttons
5 (page 23)
8 A (Stand by) button
9 Headphone jack (mini jack) (page 42)
Turn the TV on from standby
mode
Press the A button or the CHANNEL
p buttons to turn the TV on from
standby mode.
When the TV is turned on, the power lamp
lights blue.
To turn the TV off:
Press the A button again.
The power lamp goes off.
Caution
•The A button on the TV does not fully
isolate the TV from the AC supply. If
you are not going to use the TV for a
long period, be sure to disconnect the
AC plug from the AC socket.
Choose a TV channel
Press the CHANNEL p buttons to
choose a programme number (PR) or
a VIDEO terminal
Press the TV/VIDEO button to choose a
VIDEO terminal.
Adjust the volume
Press the VOLUME q buttons
The volume level indicator appears.
Using the Menu
Use the MENU/OK button
Refer to “Using the TV’s menu” (see
page 23) for details of using the menu.
Using the Illumination
When the TV is turned on the Illumination
lamp lights. To adjust the illumination
settings, refer to “ILLUMINATION” on
page 34.
POWER PROGRAM/TIMER
4
5
6
7
8
9
LT-Z32&26SX5_Eng.book Page 10 Wednesday, May 18, 2005 5:54 PM
11
ENGLISH
LT-Z32/26SX5 / LCT1869-002A / English
Remote control buttons and functions
1 Muting button
2 Number buttons
3 1 button
4 c button
5 2 button
6 4 button
7 7 buttons
8 5 button
9 6 p buttons
0 VCR/DVD/Teletext control buttons
- p buttons
= d (Favourite) button
~ # (Standby) button
! PIP/TV/DVD switch
@ g (Text) button
# Colour buttons
$ H button
% a button
^ b button
& 7 q buttons
* f (Freeze) button
( X (Multi) button
) c (Select) button
Turn the TV on or off from
standby mode
Press the # (standby) button to turn
the TV on or off
When the TV is turned on, the power lamp
lights blue.
• The power can be turned on by pressing
the 4 button, 6
p buttons or Number buttons.
~
!
0
3
4
5
9
6
7
8
-
@
%
^
(
&
$
1
2
#
=
*
)
To turn the TV on or off, set the PIP/TV/
DVD switch on the remote control to the
TV position and press the # button.
If the PIP/TV/DVD switch on the remote
control is set to the DVD position, the TV
will not be turned on or off even if the #
button is pressed.
LT-Z32&26SX5_Eng.book Page 11 Wednesday, May 18, 2005 5:54 PM
12
Remote control buttons and functions
LT-Z32/26SX5 / LCT1869-002A / English
ENGLISH
Choose a TV channel and
watch images from external
devices
Use the number buttons:
Enter the programme number (PR)
of the channel using the number
buttons.
Example:
•PR 6 → press 6
• PR 12 → press 1 and 2
Use the 6 p buttons:
Press the 6 p buttons
to choose the programme number
(PR) you want or a VIDEO
terminal.
Use the 4 button:
Press the 4 button to
choose a VIDEO terminal.
• The leading character is changed from V
to S (eg V1 is changed to S1) when
VIDEO-1 or VIDEO-2 is connected to the
S terminal.
• If you do not have a clear picture or no
colour appears, follow the operation
procedure “COLOUR SYSTEM” on
page 27.
• If you cannot hear the normal sound even
if the picture of the TV channel appears
normally. Follow the description “EDIT/
MANUAL” on page 35 to use the
MANUAL function to change the
SYSTEM setting.
• Since this TV is designed to make full use
of the resolution of the original video
source, the motion may appear unnatural
when the video source is input with
progressive-scanning component signals.
• If this happens, change the output setting
of the connected device to interlace-
scanning component signal output. See
the instructions that came with the device
for more information.
• The PC sound is the same as the VIDEO-3
sound.
To return to a TV channel:
Press the 4 button, the
6 p buttons or the number
buttons.
To use the programme number PR 0
(AV):
When the TV and VCR are connected only
by the aerial cable, choosing the programme
number PR 0 (AV) allows you to view
images from the VCR. Set the VCR RF
channel to the programme number PR 0
(AV) manually. For details, see “EDIT/
MANUAL” on page 35.
(HDMI)
4
4
Programme
numbers
PR 1 – PR 99
or
or
LT-Z32&26SX5_Eng.book Page 12 Wednesday, May 18, 2005 5:54 PM
Remote control buttons and functions
13
ENGLISH
LT-Z32/26SX5 / LCT1869-002A / English
Adjust the volume
Press the 7 q buttons to
adjust the volume.
The volume level indicator appears and the
volume changes as you press the 7
q buttons.
Muting the sound
Press the
l
(muting) button to
turn off the sound.
Pressing the
l
(muting) button again
restores the previous volume level.
Display function
You can see the channel number of the
programme you are watching or the PR
LIST.
From the PR LIST, you can choose a channel
or VIDEO terminal.
Press the
5
button to display
the information you want to see.
Pressing the
5
button changes the
display as follows:
Channel number display:
The channel number and channel name
(when the channel name is registered) of the
programme you are watching or the VIDEO
terminal number is displayed.
PR LIST:
The programme number (PR) and VIDEO
terminal list is displayed.
Pressing the a button after choosing the
programme number (PR) or VIDEO terminal
with the 7 buttons will display the
chosen programme or VIDEO terminal.
• For programme numbers (PR) for which
the CHANNEL GUARD function is set,
the n (CHANNEL GUARD) mark is
displayed. For details see “CHANNEL
GUARD” on page 31.
• The VIDEO terminals are registered after
the programme number PR 99.
• For programme numbers (PR) which is
registered as a favourite channel, the d
(favourite) mark is displayed. For details
see “Favourite channel function” on
page 18.
PR ID
AV
01
02
03
04
05
06
07
08
09
D0011
PR LIST
OK
+10-10
-EN
No indication
Channel number display
LT-Z32&26SX5_Eng.book Page 13 Wednesday, May 18, 2005 5:54 PM
14
Remote control buttons and functions
LT-Z32/26SX5 / LCT1869-002A / English
ENGLISH
ZOOM function
You can change the screen size according to
the picture aspect ratio. Choose the optimum
one from the following ZOOM modes.
• The ZOOM mode is fixed at FULL when
you are using the TV as a PC screen or
watching a 1080i or 720p picture signal.
AUTO:
When a WSS (Wide Screen Signalling)
signal, which shows the aspect ratio of the
picture, is included in the broadcast signal or
the signal from an external device, the TV
automatically changes the ZOOM mode to
16:9 ZOOM mode or FULL mode according
to the WSS signal.
If a WSS signal is not included, the picture is
displayed according to the ZOOM mode set
with the 4:3 AUTO ASPECT function.
• For details of the 4:3 AUTO ASPECT
function, see “4:3 AUTO ASPECT” on
page 28.
• When the AUTO (WSS) mode does not
function correctly due to poor WSS signal
quality or when you want to change the
ZOOM mode, press the c button
and change to another ZOOM mode.
REGULAR:
Use to view a normal picture (4:3 aspect
ratio) as this is its original shape.
PANORAMIC:
This stretches the left and right sides of a
normal picture (4:3 aspect ratio) to fill the
screen, without making the picture appear
unnatural.
• The top and bottom of the picture are
slightly cut off.
14:9 ZOOM:
This zooms up the wide picture (14:9 aspect
ratio) to the upper and lower limits of the
screen.
16:9 ZOOM:
This zooms up the wide picture (16:9 aspect
ratio) to the full screen.
16:9 ZOOM SUBTITLE:
This zooms up the wide picture (16:9 aspect
ratio) with subtitles to the full screen.
FULL:
This uniformly stretches the left and right
sides of a normal picture (4:3 aspect ratio) to
fill the wide TV screen.
• For 16:9 aspect ratio pictures that have
been squeezed into a normal picture (4:3
aspect ratio), use the FULL mode to
restore the picture to its original shape.
Choose the ZOOM mode
1 Press the c button to display
the ZOOM menu
2 Press the 6 buttons to choose a
ZOOM mode. Then press the a
button
The picture expands and the chosen
ZOOM mode is displayed in about 5
seconds.
• The ZOOM mode may be
automatically changed by the control
signal from an external device. When
you want to return to the previous
ZOOM mode, choose the ZOOM
mode again.
D0009
AUTO
ZOOM
OK
REGULAR
PANORAMIC
14:9 ZOOM
16:9 ZOOM
16:9 ZOOM SUBTITLE
FULL
-EN
LT-Z32&26SX5_Eng.book Page 14 Wednesday, May 18, 2005 5:54 PM
Remote control buttons and functions
15
ENGLISH
LT-Z32/26SX5 / LCT1869-002A / English
Adjusting the visible area of the
picture
If subtitles or the top (or bottom) of the
picture are cut off, you can adjust the visible
area of the picture manually.
1 Press the c button
The ZOOM menu appears.
2 Press the a button to display the
ZOOM mode indicator
The indicator appears.
3 While it is displayed, press the 6
buttons to change the position of
the picture
• You cannot adjust the visible area in
REGULAR or FULL mode.
The visible area adjustment is saved even
after the TV channel is changed.
However, it is cancelled if the following
operations are performed.
• The power is turned off/on
• The ZOOM mode is changed
• The X (Multi) button, f (Freeze)
button, or g (Text) button is pressed
• The TV is switched between TV mode
and VIDEO mode
CINEMA SURROUND function
You can enjoy sounds with a wider
ambience.
• This function does not work for the sound
from headphones.
Press the 2 button to select
one of CINEMA SURROUND modes
HIGH/LOW:
When you listen to stereo sound, please
select HIGH or LOW mode.
You can enjoy sound similar to the
experience at the theatre.
When you combine the functions of A.H.B.
and BBE, you can enjoy more powerful
sound.
• When you set the CINEMA SURROUND
function to HIGH mode, there may be
slight volume distortion. If that occurs,
please switch to LOW mode. The effect
of CINEMA SURROUND functions will
be less noticeable, but the volume
distortion will be corrected.
MONO:
Select the MONO mode, when you listen to
the mono sound.
You can enjoy the sound for a wider
audience similar to stereo sound.
OFF:
The CINEMA SURROUND function
switches off.
• You can choose the CINEMA
SURROUND mode with the “SOUND
menu” (see page 29).
Using the “Freeze” function
You can view the current programme as a
still picture.
1 Set the PIP/TV/DVD switch to the
PIP position
When using the “Freeze” function, set the
PIP/TV/DVD switch to the PIP position.
2 Press the f button
The still picture of the current picture will
appear.
16 : 9 ZOOM
D0010-EN
D0056
current
programme
still picture
LT-Z32&26SX5_Eng.book Page 15 Wednesday, May 18, 2005 5:54 PM
16
Remote control buttons and functions
LT-Z32/26SX5 / LCT1869-002A / English
ENGLISH
To cancel the “Freeze” function:
Press the f button, the 6
p buttons or the number buttons.
• The “Freeze” function does not work
while a sub-picture is displayed.
• The still picture cannot be output from
the TV.
• The “Freeze” function does not work
for picture of PC signals.
Using the “Multi-picture”
function
1 Set the PIP/TV/DVD switch to the
PIP position
When using the “Multi-picture” function,
set the PIP/TV/DVD switch to the PIP
position.
2 Press the X button
The “Multi-picture” menu appears.
3 Press the 5 buttons to choose
the number of screens and then
press the a button
2-pictures multi:
With 1125i and 750p signals, the screen is
split into two as shown below.
12-pictures multi:
• When set to 2-pictures multi, you can
view a TV picture and a picture from
an external device. You cannot view a
TV picture on more than one screen at
the same time.
• When 12-pictures multi is set, pictures
from external devices are not displayed.
• When watching a picture from the
HDMI signal, 12-pictures multi can
not be displayed.
• When set to 2-pictures multi, the main-
picture can be changed by pressing the
6 p buttons. The sub-
picture screen can be changed by
pressing the 6 buttons.
When set to 12-pictures multi and
there are more than 12 pictures, the
next or previous 12 screens can be
displayed by pressing the
6 p buttons.
• When set to 2-pictures multi, the main-
picture sound from the TV speaker can
be changed to the sub-picture sound by
pressing the c button when the PIP/
TV/DVD switch is set to the PIP
position. (The speaker mark moves
from the main-picture to the sub-
picture.)
The sound changes to the main-picture
sound if the c button is pressed again.
When the headphones are connected,
you can listen to the sound from the
side at which the headphones mark is
displayed. No sound comes from the
TV speaker.
• When set to 2-pictures multi, picture
from HDMI can not be displayed on
the Sub-picture.
• The pictures from VIDEO-1 (or
VIDEO-3) cannot be displayed in the
sub-picture when the VIDEO-1
SETTING (or VIDEO-3 SETTING) is
set to COMPONENT (see page 39).
1
D0101
212
D0102
1
D0103
2
D0104
12
Choose to return to one screen.
Choose to change to 2-pictures multi.
Choose to change to 12-pictures multi.
D0056
Main-
picture
Sub-
picture
D1056
Main-
picture
Sub-
picture
D0058
Still
pictures
Moving
picture
LT-Z32&26SX5_Eng.book Page 16 Wednesday, May 18, 2005 5:54 PM
Remote control buttons and functions
17
ENGLISH
LT-Z32/26SX5 / LCT1869-002A / English
• The “Multi-picture” function does not
work for a PC signals.
• When set to 12-pictures multi, press
the 7 buttons to choose the
screen you want to view and the press
the a button to display that picture
on the whole screen.
• The BLUE BACK function does not
work when the “Multi-picture”
function is being used.
• The ZOOM function does not work
when the “Multi-picture” function is
being used.
To return the “Multi-picture” to one
screen:
Press the X button, press the 5
buttons to choose one screen, and then
press the a button.
• Pressing the 4 button will
also return the display to one screen.
RETURN PLUS function and
Return function
The 1 button has two functions;
the RETURN PLUS function and the Return
function. If a channel has been registered as
the “Return Channel”, the RETURN PLUS
function operates. If there is no setting for the
“Return Channel”, the Return function
operates.
RETURN PLUS
By registering a channel you frequently view
as the “Return Channel”, you can select that
channel at any time simply by pressing the
1 button.
To register a TV channel as the
“Return Channel”:
Choose the Programme number to which the
channel you want to register has been set,
and press the 1 button and hold
for more than 3 seconds continuously.
“RETURN PLUS PROGRAMMED!” is
displayed and the registration is completed.
To cancel a TV channel registered as
the “Return Channel”:
While viewing any TV channel, press the
1 button and hold for more than 3
seconds continuously. “RETURN PLUS
CANCELED!” is displayed and the
registration is cancelled.
• When you turn off the TV, the registration
for the “Return Channel” is cancelled.
• If you want to view the “Return Channel”
and another TV channel alternately, first
choose a channel other than the “Return
Channel”. And then press the
1 button to change the channel
to the “Return Channel” In this way, you
can view two channels alternately by
pressing the 1 button.
Return function
The TV temporarily memorises the TV
channel that was chosen right before the
current TV channel as the “Last Channel”.
By pressing the 1 button, you can
alternately view the current TV channel and
the “Last Channel”.
If you want to view two channels alternately
by using the Return function, first choose one
TV channel and then choose the other TV
channel with the number buttons. If you
choose the TV channel without using the
number buttons, there are cases where a
channel other than the one you first chose is
registered as the “Last Channel”.
LT-Z32&26SX5_Eng.book Page 17 Wednesday, May 18, 2005 5:54 PM
18
Remote control buttons and functions
LT-Z32/26SX5 / LCT1869-002A / English
ENGLISH
Favourite channel function
You can register your favourite TV channels
(PR 1 – PR 99) in the number buttons 1 to 4.
After registering, the channel can be called
by pressing the d (favourite) button and a
number button 1 to 4.
Favourite channel registration
1 In the normal screen, choose a TV
channel (PR 1 – PR 99) that you
want to register
For details, refer to “Choose a TV channel
and watch images from external devices”
on page 12.
2 Press and hold the d (favourite)
button for three seconds or more
Then “SET 1-4?” appears on the screen.
3 Press one of the number buttons 1
to 4
The current channel is registered in the
pressed number button.
After “PROGRAMMED!” appears on the
screen, the favourite channel icon appears
at the top-right of the screen.
• If the channel you are trying to register
is already registered in one of the other
number buttons 1 to 4, “NOT
AVAILABLE” appears on the screen.
• Channels locked with the CHANNEL
GUARD function cannot be registered.
• If AUTO PROGRAM is performed,
the registered favourite channels are
reset.
• When you want to delete a favourite
channel, delete the set channel and set
contents with FAVOURITE SETTING
(see page 33) in the FEATURES menu.
Calling the favourite channel
1 In the normal screen, press the d
(favourite) button
Then “FAVOURITE1-4?” appears.
2 Press one of the number buttons 1
to 4
The called favourite channel appears on
the screen.
• If a number button in which no
channel is registered is pressed, “NO
MEMORY” appears on the screen.
Setting the picture effect
When a favourite channel has been chosen
with the d (favourite) button and number
buttons 1 to 4, picture effect settings can be
memorised for each favourite channel by
setting the picture effects in the PICTURE
menu (see page 25).
The following items in the PICTURE menu
(see page 25) are memorised.
PICTURE MODE
BACK LIGHT
CONTRAST
BRIGHT
SHARP
COLOUR
TINT
WHITE BALANCE
DIGITAL VNR
COLOUR SYSTEM
The last setting made for each item is
memorised.
LT-Z32&26SX5_Eng.book Page 18 Wednesday, May 18, 2005 5:54 PM
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
