3D Systems Cubify CUBEX Trio Replacement Manual

Brand: 3D Systems

Model: Cubify CUBEX Trio

Type: Replacement Manual

This manual is also suitable for

Cubify CUBEX Duo

3D Systems Cubify CUBEX Trio is a 3D printer that offers a range of features and capabilities to help you create high-quality 3D prints. With its triple-jetting technology, the CUBEX Trio can print in three different colors or materials simultaneously, giving you the ability to create complex and multi-colored objects. The printer also features a large build volume, allowing you to print objects up to 10 x 10 x 10 inches in size.

The CUBEX Trio is easy to use, with a user-friendly interface and a variety of software options to help you design and print your models. The printer is also compatible with a range of materials, including PLA, ABS, and HIPS, giving you the flexibility to choose the right material for your project.

CUBEX

Print Jet

Replacement

Manual

Contents

Removing the damaged print jet ................................................................................3

Installing the new print jet...........................................................................................7

Levelling the print tips for CubeX Duo/Trio...............................................................10

Setting Print Tip offsets............................................................................................11

Fastening the print tip on a CubeX...........................................................................12

What you will need

Print jet assembly

2.5mm Hex driver

Pliers

Before beginning this process please remove all filament from the print jets

and check that your print pad is level. For instructions on how to do this

please refer to the CubeX users guide

Removing the damaged print jet

1. Turn off the CubeX printer and unplug it from the mains power.

2. Unplug the two white looms from the top of the damaged print jets sensor

board,

3. Label the Print Jet motor looms with the corresponding print jet number and

unplug them.

4. Remove the bolts holding the Feed Tube mount in place. The amount of bolt

will vary depending on the amount of print jets your CubeX has.

A CubeX will have the bolts circled in red.

A CubeX duo will have the two bolts circled in red and the bolt circled in green.

A CubeX trio has the bolts circled in red, green and blue.

5. You should now be able to move the Feed Tube mount from the top of the

print jets to expose the print jet mounting bolt.

6. Remove the mounting bolt. This can be very tight.

7. You should now be able to lift the print jet away from the Print Jet carriage

plate.

Installing the new print jet

1. Check your Print Jet is assembled and that the print tip moves freely when

pushed in and out of the drive. The Print tip moves freely for the levelling

process. Once the levelling process has been completed the Print tip will be

locked off.

If your Print Jet and print tip are not assembled together when you receive them, you

can assemble them by inserting the locating end of the Print tip into the Print Jet as

pictured below.

2. Place the Print Jet onto the Print Jet carriage plate as pictured, note the

locating standoff and corresponding hole present on the Print Jet

3. Ensure that the wires from the Print tip are orientated to travel straight up to

the Sensor board

4. Replace the M3 x 20 bolt into the hole as pictured and fasten. This must be

tight.

5. Re attach the Feed Tube mount.

6. Plug the motor looms back into their corresponding motors.

7. Plug in the Print Jet sensor board looms.

Levelling the print tips for CubeX Duo/Trio

If your CubeX only has a single print jet please see section ‘Fastening the print

tip on a CubeX’

1. Power on the CubeX printer

2. To clean the nozzles for levelling, put the CubeX printer into PJ-Control mode.

Heat all of the print jets EXCEPT for the new one to 230° and clean of any

plastic debris with pliers. Allow the Print Jets to cool down.

3. Put the CubeX printer into manual move mode.

4. Raise the print pad until it is approximately 5mm away from the print tips.

5. Slowly raise the print pad until it lifts the new print tip in line with the others. All

three print tips should be touching the bed without putting any pressure on it.

6. Turn the CubeX printer off and unplug it from the mains power supply.

7. Using the 2.5mm hex driver, tighten the print jet holding bolt (pictured) to lock the

print jet in place.

With the print tips levelled you can now turn on the CubeX printer and set the print tip

offsets

Setting Print Tip offsets

See the CubeX user guide for instructions on how to set your print tip offsets.

Fastening the print tip on a CubeX

A CubeX with a single print jet does not have a second or third nozzle to reference

the print tip level. Instead you have to use the CubeX wiping stick.

1. Power on the CubeX printer

2. Put the CubeX into manual move.

3. Raise the print pad until it is approximately 5mm away from the print tip.

4. Slowly raise the print pad until the print tip is touching it.

5. Continue raising the print pad until there is approximately 0.5mm between the

print pad and the CubeX wiping stick.

6. Turn the CubeX printer off and unplug it from the mains power supply.

7. Using the 2.5mm hex driver, tighten the print jet holding bolt (pictured) to lock

the print jet in place.

With the print tip fastened you can now turn on the CubeX printer and start printing.

3D Systems Cubify CUBEX Trio Replacement Manual

Brand: 3D Systems

Model: Cubify CUBEX Trio

Type: Replacement Manual

This manual is also suitable for

Cubify CUBEX Duo

Download PDF

report

3D Systems Cubify CUBEX Trio Replacement Manual

This manual is also suitable for

3D Systems Cubify CUBEX Trio Replacement Manual

Related papers

Other documents