Secura QSF210 User manual

Brand: Secura

Model: QSF210

Category: Flat panel wall mounts

Type: User manual

QSF

210

INSTRUCTION MANUAL

We’ll Make It Stress-Free

If you have any questions along the way, just give us a call.

1-800-359-5520 We’re ready to help!

Scan for easy install video

san.us/1142

Wood Stud Install

Concrete Install

Tape

Measure

Pencil Level

Screw

driver

Electric

Drill

Socket

Wrench

Stud

Finder

Awl

Wood

Drill Bit

Masonry

Drill Bit

Hammer

3/8 in.

(10 mm)

1/2 in.

(13 mm)

7/32 in.

(5.5 mm)

CAUTION: IMPORTANT SAFETY INSTRUCTIONS — PLEASE READ ENTIRE MANUAL PRIOR TO USE — SAVE THESE INSTRUCTIONS

Before getting started, let’s make sure this mount is perfect for you!

No? Perfect – you may continue.

Yes? This mount is NOT compatible.

Visit secura-av.com or call 1-800-359-5520

(UK: 0800 056 2853) to ﬁ nd a compatible mount.

Please read through these instructions completely to be sure you’re comfortable with this easy install process.

Also check your TV owner’s manual to see if there are any special requirements for mounting your TV.

If you do not understand these instructions or have doubts about the safety of the installation, assembly or use

of this product, contact Customer Service at

1-800-359-5520 (UK: 0800 056 2853).

Do you have

all the tools

needed?

What is your

wall made of?

Ready to begin?

CAUTION:

DO NOT exceed the maximum weight

indicated. This mounting system is intended for use only

with the maximum weights indicated. Use with products

heavier than the maximum weights indicated may result

in collapse of the mount and its accessories, causing

possible injury.

Solid concrete or

concrete block?

Perfect!

Drywall with

wood studs?

Perfect!

CAUTION:

DO NOT

install into

drywall alone

Unsure?

Call Customer Service:

1-800-359-5520

(UK: 0800 056 2853)

25 lbs.

(11.3 kg)

Does your TV

(including accessories)

weigh MORE than

25 lbs. (11.3 kg)?

CAUTION: Avoid potential personal injury or property damage!

● This product is designed for use in wood stud, solid concrete, and concrete block walls - DO NOT install into drywall alone

● The wall must be capable of supporting ﬁ ve times the weight of the TV and mount combined

● Do not use this product for any purpose not explicitly speciﬁ ed by manufacturer

● Manufacturer is not responsible for damage or injury caused by incorrect assembly or use

3.94in

100mm

7.87in

200mm

7.87in

200mm

.35in

8.8mm

8.15in

207.1mm

2.80in

71mm

6.40in

162.6mm

30deg

10.47in

265.9mm

16deg DOWN TILT

4deg UP TILT

8.80in

223.6mm

8.80in

223.6mm

10.26in

260.5mm

3.20in

81.4mm

.86in

21.9mm

30° SWIVEL LEFT AND RIGHT WITH AN APPROXIMATE 32" TV

TV INTERFACE

WALL PLATE

FULLY ASSEMBLED MOUNT

TOP VIEW - EXTENDED

TOP VIEW - RETRACTED

SIDE VIEW - EXTENDED

SIDE VIEW - RETRACTED

3-D

in.

[mm]

Dimensions

NOTE: Not all hardware included will be used.

WARNING: This product contains small items that could be a choking hazard if swallowed.

Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to

your dealer; contact Customer Service. Never use damaged parts!

Supplied Parts and Hardware

M4 x 8mm

M4 x 12mm

M6 x 12mm

M4 x 35mm

M6 x 35mm

M6/M8

M8 x 16mm

M8 x 35mm

M8 x 20mm

STEP 1 Parts and Hardware

TV Screws

Washers

Spacers

TV Bracket

Extenders

TV Bracket

TV Bracket Screws

(TV Bracket extenders)

22mm

01 x1

02 x4

03 x8

04 x4

08 x4

09 x4

10 x4

11 x4 12 x4

13 x4

05 x4

06 x4

07 x4

5/16 x 2¾ in.

5/16 in.

Fischer UX 10 x 60R

Concrete Anchors

For concrete installations ONLY

CAUTION: Do not use in drywall or wood

STEP 2 Parts and Hardware

STEP 3 Parts and Hardware

Additional Parts and Hardware

Wall Plate Assembly

Lag Bolts

Lag Bolt Washers

Securement Washer

Securement Screw

7/32 in.

Allen Key

Cable Ties

14 x1

15 x2

16 x2

17 x2

18 x1

19 x1

8mm

STEP 1 Attach TV Bracket to TV

These smaller hole patterns only use TV bracket

Do not use the four TV bracket extenders

and eight screws

10.0

7.5

10.0

7.5

1.1 Measure Your TV Hole Pattern 1.2 Assemble Your TV Bracket

Measure the width and height of your TV hole pattern in cm.

Record your measurements:

Determine which TV bracket configuration to use, A, B, or C

based on your TV hole pattern measurements.

inches

Width ______cm x Height ______cm

inch dimensions are approximate

inches cm mm

3 7.5 75

4 10 100

7 ⅞ 20 200

7.5 x 7.5

10.0 x 10.0

Dimensions in cm

TV Hole Pattern

Measurement

Assemble TV bracket extenders

onto TV bracket

as illustrated.

Secure using eight screws

in the corner holes shown.

Assemble TV bracket extenders

onto TV bracket

as illustrated.

Secure using eight screws

in the corner holes shown.

20.0

10.0

20.0 x 20.0

Dimensions in cm

TV Hole Pattern

Measurement

20.0 x 10.0

Dimensions in cm

TV Hole Pattern

Measurement

M6 M8

FLAT BACK ROUND BACK CABLESINSET HOLES

1.3 Select TV Screw Diameter 1.4 Select TV Screw Length

If your TV has a flat back, use the shorter screws.

Spacers and longer screws are supplied to accommodate:

● irregular / round back TVs

● TVs with inset mounting holes

● extra space needed for cables

Hand thread screws into the threaded inserts

on the back of your TV to determine which

screw diameter (M4, M6 or M8) to use.

Too Short

Too Long

CAUTION:

Verify adequate thread

engagement with your screw/

washer/spacer combination AND

TV bracket. (STEP 1.5)

- Too short will not hold the TV.

- Too long will damage the TV.

Correct

Standard configurations

are shown. For special

applications, or if you

are uncertain about your

hardware selection,

contact Customer Service

at 1-800-359-5520.

Flat Back

Round Back / Extra Space

1.5 Attach TV Bracket

NOTE: For 200 x 200 or

200 x 100 hole patterns, you may

need to loosen the screws

align the bracket extenders

After bracket extenders

are

secured to the back of your TV,

re-tighten screws

TV Bracket Conﬁ gurations

and

(from page 7)

Conﬁ guration B Illustrated, with spacers

TV Bracket Conﬁ guration

(from page 6)

Illustrated with spacers

04 05 06 07

11 12

08 09 10

11 12

Position your TV bracket configuration (A, B, or C)

over your TV hole pattern - making sure the bracket is centered over the TV hole pattern and level.

CAUTION: Avoid potential personal injuries and property damage! DO NOT use power tools for this step. Tighten the screws only enough to secure the TV

bracket to the TV. DO NOT overtighten the screws.

IMPORTANT: Ensure TV bracket is securely fastened before moving on to the next step.

2 3

1. Locate your stud. Verify and mark the center of the stud by finding the stud edges using an awl, a thin nail, or an edge to edge stud finder.

2. Position the wall plate assembly

at your desired height and line up the holes with your stud center line. Level the wall plate assembly

and mark the hole locations.

3. Drill pilot holes using a 7/32 in. (5.5 mm) diameter drill bit.

IMPORTANT: Pilot holes must be drilled to a depth of 2 ¾ in. (70 mm). Be sure to drill into the center of the stud.

CAUTION: Avoid potential personal injury or property damage!

● Drywall covering the wall, must not exceed 5/8 in. (16 mm)

● Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal 1½ x 3½ in. (38 x 89 mm)

● Stud center must be verified

7/32 in.

(5.5 mm)

2 ¾ in. (70 mm)

Max. 5/8 in.

(16 mm)

STEP 2A Attach Wall Plate to Wall

Wood Stud Option

4. Install wall plate assembly

using two lag bolts

and two washers

. Tighten the lag bolts

only until the washers

are

pulled firmly against the wall plate assembly

NOTE: If needed, you can make small level adjustments to the wall plate assembly

by loosening the bottom lag bolt

and shifting the

wall plate assembly

until level. Tighten the bottom lag bolt

when adjustments are complete.

CAUTION: Avoid potential personal injury or property damage! All lag bolts

MUST BE firmly tightened to prevent unwanted

movement of the wall plate assembly

Ensure the wall plate assembly is securely fastened to the wall before continuing on to the next step.

Go to STEP 3 on PAGE 14.

1. Position the wall plate assembly

on the wall at your desired height. Level the wall plate assembly

and mark the hole locations.

2. Drill two pilot holes using a 3/8 in. (10 mm) diameter masonry drill bit.

IMPORTANT: Pilot holes must be drilled to a depth of 3 in. (75 mm). Never drill into the mortar between blocks.

CAUTION: Avoid potential personal injury or property damage!

● Mount the wall plate assembly

directly onto the concrete surface.

● Minimum solid concrete thickness: 8 in. (203 mm)

● Minimum concrete block size: 8 x 8 x 16 in. (203 x 203 x 406 mm)

STEP 2B

Attach Wall Plate to Wall

Solid Concrete or Concrete Block Option

3/8 in.

(10 mm)

3 in. (75 mm)

3. Insert two anchors

CAUTION: Be sure the anchors

are seated flush with the concrete surface.

4. Install wall plate assembly

using two lag bolts

and two washers

. Tighten the lag bolts

only until the washers

are

pulled firmly against the wall plate assembly

CAUTION: Improper use could reduce the holding power of the lag bolt

. DO NOT over-tighten the lag bolts.

NOTE: If needed, you can make small level adjustments to the wall plate assembly

by loosening the bottom lag bolt

and shifting the wall

plate assembly

until level. Tighten the bottom lag bolt

when adjustments are complete (see page 11).

HEAVY! You may need assistance with this step.

STEP 3 Hang TV onto Wall Plate

1. Position the arm of wall plate assembly

so the elbow is bent 90 degrees and pressed against the wall.

2. Hang the TV onto the arm of wall plate assembly

by first hooking the top support, then resting the TV into place.

3. Lock the TV to the wall plate assembly

with securement screw

and securement washer

CAUTION: Avoid potential personal injuries and property damage! This securement screw

must be installed to secure the TV

onto the wall plate assembly

Top Support

Manage Cables

If desired, thread a supplied cable tie

through the loop provided on the arm of the wall plate assembly

, and secure your TV cables

along the arm for a clean look.

IMPORTANT: Fully extend the arm of wall plate assembly

to ensure you have enough slack in the cables for full TV movement.

TV Adjustments

TILT ADJUSTMENT

Your TV should adjust easily when moved, then stay in place.

If your TV is too loose or too tight, adjust the tilt tension

knob by hand.

NOTE: Once your TV is in place, tighten the tilt tension

knob to prevent unwanted movement.

LEVEL ADJUSTMENT

To adjust the leveling of your TV, loosen the securement screw

level your TV, then tighten securement screw

IMPORTANT: This securement screw

must be installed to

secure the TV onto the wall plate assembly

Tighten

Loosen

Tilt Tension Knob

Tighten

Loosen

Arm Tension

Screw

14 mm (9/16 in.)

socket

REMOVING THE TV

To remove your TV from the

wall plate assembly

disconnect all cables and then

reverse the

procedures in STEP 3.

SWIVEL ADJUSTMENT

Your TV should adjust easily when moved,

then stay in place.

If your TV is too loose or too tight, adjust

the arm tension screws using hex key

and a 14 mm (9/16 in.) socket.

EXTENSION/RETRACTION ADJUSTMENT

Your TV should adjust easily when moved,

then stay in place.

If your TV is too loose or too tight, adjust

the arm tension screws using hex key

Arm Tension

Screw

Loosen

Tighten

HEAVY! You may need

assistance with this step.

Features

Fully articulating arm with 3

pivot points creates optimal

viewing positions

TV tilts up or down for the

perfect viewing angle

Level

adjustments

create a

worry-free

installation

Adjustments allow ﬁ ngertip control

of TV or restriction of TV movement

TV bracket expands

to ﬁ t TV hole patterns

from 75 x 75 mm up to

200 x 200 mm

Cable tie hook

holds cables

along mount arm

for a clean look

Milestone AV Technologies and its a liated corporations and subsidiaries (collectively, “Milestone”), intend to make this manual accurate and complete. However,

Milestone makes no claim that the information contained herein covers all details, conditions, or variations. Nor does it provide for every possible contingency in

connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind.

Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy,

completeness or su ciency of the information contained in this document.

All other brand names or marks are used for identiﬁ cation purposes and are trademarks of their respective owners.

Milestone AV Technologies • 6436 City West Parkway • Eden Prairie, MN 55344 USA 6901-002597 00

Thank you for choosing Secura! Please take a moment to let us know how we did:

Call us: 1-800-359-5520

UK: 0800 056 2853

Email us: info@secura-av.com