Xtant RGM Owner's manual

Brand
Xtant
Model
RGM
Type
Owner's manual

Xtant RGM is a remote gain module that allows you to control the gain of your amplifier from a remote location. This is useful for adjusting the gain of your amplifier without having to access the amplifier itself, which can be difficult or impossible in some installations. The RGM is also useful for adjusting the gain of your amplifier while you are listening to music, so you can find the perfect balance between sound quality and volume.

The RGM is easy to install and use. Simply connect the RGM to your amplifier's accessory port and run the supplied cord to the location in your vehicle where you want to mount the gain knob. The RGM knob is then used to control the gain of your amplifier.

Xtant RGM is a remote gain module that allows you to control the gain of your amplifier from a remote location. This is useful for adjusting the gain of your amplifier without having to access the amplifier itself, which can be difficult or impossible in some installations. The RGM is also useful for adjusting the gain of your amplifier while you are listening to music, so you can find the perfect balance between sound quality and volume.

The RGM is easy to install and use. Simply connect the RGM to your amplifier's accessory port and run the supplied cord to the location in your vehicle where you want to mount the gain knob. The RGM knob is then used to control the gain of your amplifier.

Owner’s Manual – RGM
Remote Gain Module
7676 South 46th Street • Phoenix, AZ 85040
602.449.8268 • Xtant.com
# NDM159
INSTALLING THE RGM
STEP 1: Locating the Connectors
INSTALLING THE RGM
STEP 2: Installing on Circuit Board
INSTALLING THE RGM
STEP 3: Rear & Surface Mount
FFOORR RREEAARR MMOOUUNNTT
A Gently pull the black gain knob off the shaft to
remove it
B Plug the cord into the RGM control box
C Use a /” size drill bit to make a hole in the surface
you wish to mount the knob to
D Place the control box behind the panel and insert the
knob through the hole
E Replace the nut located in the parts bag on the shaft
by turning it clockwise and then gently push the
knob back onto the shaft
F The RGM knob is now controlling the gain of
your amplifier
FFOORR SSUURRFFAACCEE MMOOUUNNTT
A Plug supplied cord into RGM control box
B Secure control box to surface where you wish to
mount it with supplied screws
C The RGM knob is now controlling the gain of
your amplifier
The RGM is designed to be adjusted with the use of a
control knob
A Plug the supplied cord into the RGM’s socket on
the module board
B Turnoff amplifier Remove amplifier cover and
locate the Accessory Port
C Remove the two header jumpers and locate the
missing pin (“key”) on the port
D Align the blocked receptacle on the right angle
header connector with the missing pin and press
the RGM onto the mounting port
E Rotate the amplifier’s gain control clockwise
(fully) to  dB
F Run the RGM’s cord out of the amp near the
RCA inputs
G Replace the amplifier’s cover and put the screws
back in to secure it to the baseplate
H Run the supplied  foot cord to the location in
the vehicle where you want to mount the gain knob
iilllluussttrraattiioonn
iilllluussttrraattiioonn
BBOOTTTTOOMM OOFF
RRGGMM
CCIIRRCCUUIITT BBOOAARRDD
TTOOPP OOFF
RRGGMM
CCIIRRCCUUIITT BBOOAARRDD
HHEEAADDEERR CCOONNNNEECCTTOORR
llooccaattiinngg ““kkeeyy””
RRIIGGHHTT AANNGGLLEE
HHEEAADDEERR CCOONNNNEECCTTOORR
A Remove the RGM from the packaging and
inspect the circuit board
B Locate the header connectors soldered onto the
top and bottom of the circuit board
See illustration 
C Notice that one of the openings on both header
connectors is blocked by white filler material
The RGM’s mounting system utilizes this
blocked receptacle as the “key” to insure proper
positioning when installing the RGM onto the
amplifier’s mounting port
  • Page 1 1
  • Page 2 2

Xtant RGM Owner's manual

Brand
Xtant
Model
RGM
Type
Owner's manual

Xtant RGM is a remote gain module that allows you to control the gain of your amplifier from a remote location. This is useful for adjusting the gain of your amplifier without having to access the amplifier itself, which can be difficult or impossible in some installations. The RGM is also useful for adjusting the gain of your amplifier while you are listening to music, so you can find the perfect balance between sound quality and volume.

The RGM is easy to install and use. Simply connect the RGM to your amplifier's accessory port and run the supplied cord to the location in your vehicle where you want to mount the gain knob. The RGM knob is then used to control the gain of your amplifier.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents