Crypto F200 User manual

Brand: Crypto

Model: F200

Type: User manual

Crypto F200, a powerful ADSL USB modem, offers a reliable and high-speed internet connection for your home or office. With download speeds of up to 8Mbps and upload speeds of up to 1Mbps, you can enjoy a seamless and lag-free browsing, streaming, and gaming experience. It supports various protocols, including PPPoA, PPPoE, and bridged Ethernet, making it compatible with most ISPs. The F200 is easy to set up and use, with a user-friendly interface and clear instructions provided in the user manual.

USER MANUAL

F200 ADSL USB MODEM

CONTENTS

1. Introduction 4

2. Specifications 4

2.1 ADSL Standards supported 4

2.2 Supported Protocols 4

2.3 Connections 5

3. Hardware Installation Procedures 5

3.1 Hardware Requirements 5

3.2 Preparing your network information 5

3.3 Configure the ISP parameters for your Windows XP 6

3.4 Driver Installation on Windows XP 7

3.5 Software Configuration 8

3.6 Connection to the Internet 11

4. Troubleshooting 13

1. Introduction

F200 ADSL USB modem is a high performance and high-speed device that

provides a full rate ADSL modem with the superb reliability and is a complete

solution for home and office. The F200 ADSL USB modem can have a maxi-

mum downstream data rate of up to 8Mbps and an upstream of up to 1Mbps.

You can safely enjoy the new generation broadband Internet with the F200

ADSL USB modem. Included drivers for Win98/ ME/ 2000/ XP.

2. Specifications

2.1 ADSL Standards supported:

ñSupports ITU-T G.992.1(G.DMT) and ANSI T1.413 Issue 2

ñSupports G.992.2 (G.LITE)

ñAnnex A & B

2.2 Supported Protocols:

WAN

ñPPP over ATM (PPPoA) VC MUX

ñPPP over ATM (PPPoA) with LLC/SNAP

ñPPP over Ethernet (PPPoE) with LLC/SNAP

ñPPP over Ethernet (PPPoE) with VC MUX

LAN

ñBridged Ethernet (IP over ATM) with LLC/SNAP

ñBridged Ethernet (IP over ATM) with VC MUX

ñRouted IP over ATM with LLC/SNAP

ñClassical IP over ATM

This package includes:

ñF200 USB modem

ñ1 USB cable

ñ1 RJ11 telephone cable

ñ1 CD with drivers

ñ1 users manual

2.3 Connections

USB – Connects the USB cable from the USB port of the F200 modem to the

USB port of the computer.

LINE – Connects the RJ11 telephone cable from the telephone line port of

F200 modem to the telephone plug..

LED indications:

POWER: After successfully installing the modem, the POWER LED light turns

on. It will stay on every time you start your computer.

3. Hardware Installation Procedures

3.1 Hardware Requirements

The following hardware is necessary to configure and use the F200:

ñRJ-11 (ADSL Ready) telephone Line

ñUSB cable (Included in the package)

3.2 Preparing your network information

To configure your ADSL modem smoothly, it is required that you contact your

ISP (Internet Service Provider) and acquire the following information:

Type of Mode Encapsulation used:

a. PPPoE, PPPoA, IPoA, Bridged or Routed.

DSL connection parameters:

b. For PPPoE or PPPoA, refer to Table 3 and fill-in all values (provided by your

ISP). During the driver installation, select ‘WAN’.

c.For Bridged, Routed, or IPoA, refer to Table 4 and fill-in all values (provided by

your ISP). During the driver installation, select ‘LAN’.

Table 3 WAN (PPPoE/PPPoA parameters)

Information Value

PVC Settings VPI

VCI

Encapsulation (LLC ‹ VCMux)

Information Password

Line Modulation Automatic ITU G.dmt or G.lite preferred

Automatic ANSI T1.413 i2 preferred

ITU (G.dmt or G.lite)

G.dmt

G.lite

table 4 LAN (Bridged/Routed/IPoA parameters)

Information Value

PVC Settings VPI

VCI

Encapsulation (LLC or VC Mux)

IP Information IP Address

Subnet Mask

Gateway IP Address

Preferred DNS address

Alternate DNS address (If available)

Line Modulation Automatic ITU G.dmt or G.lite preferred

Automatic ANSI T1.413 i2 preferred

ITU (G.dmt or G.lite)

G.dmt

G.lite

3.3 Configure the ISP parameters for your Windows XP

F200 is initially set to function on Annex B protocol (ADSL over ISDN). To

install the F200 based on Annex A protocol ( ADSL over PSTN), follow the

procedure below.

NOTE: THE FOLLOWING PROCEDURES APPLY FOR PPPoA MODE..

Table 5

Annex A

Driver Setup ‰È·Ï¤ÁÔ˘ÌÂ WAN

Protocol PPPoA

Encapsulation VCMUX

Modulation Automatic ITU G.dmt or G.lite preferred

VPI 8

VCI 35

USERNAME test

PASSWORD test_passw

3.4 Driver Installation on Windows XP

Step 1:

Windows will detect the newly installed device

and the screen below will appear after the

F200 USB ADSL Modem is attached to the

systems USB port.

Select "Install from a specific Location",

and click "NEXT".

Step 2:

Select "Include this location in the search"

and type d:\driver\Wan

(where D:\ the CD-ROM)

Note: If the protocol being used is Bridged,

Routed or IpoA, then type d:\driver\Lan

Step 3:

Click Continue Anyway.

This window appears only on Windows XP.

Installation continues

Step 4:

Click "Finish"

Step 5:

Left click on 'My Computer' icon and

click on 'Properties_ > _Device Manager'

Double click on Network adapters and

check to see for:

'Crypto F200 USB ADSL WAN adapter'

3.5 Software Configuration

Continue the setup process of the F200.

Step 1:

Double click on

the ‘Access Runner’ icon

Step 2:

Initially there is no connection / synchronization

with the ADSL line ‘Attempting to Activate Line’.

Press ‘ALT – P’ on your keyboard

Step 3:

Here you can see that the connection has

not been established. ‘Attempting to Activate Line’.

Click the ‘Line Setup’ tab

Step 4:

Initially it is set to Annex B (ADSL over ISDN) as

shown on the bottom right.

Note: If the line was ISDN, then we do not change it.

Step 5:

Select Annex A (ADSL over POTS) (given that the line

was PSTN). Click Apply.

Note: Incase you take out the USB plug from your

computer and plug it back to the USB port of the

computer again (does not matter if its upon shut-down

or while the computer is on), then the Annex selection

will automatically be set to Annex B. To set it back

to Annex A, please follow this procedure again.

Select the Protocol Setup tab

Step 6:

In the Virtual Path Identifier (VPI) selection, and

under Virtual Circuit 0, the value is 0.

and

In the Virtual Circuit Identifier (VCI) selection, and

under Virtual Circuit 0, the value is 35.

Step 7:

For the example insert:

VPI = 8

VCI = 35

Click Apply.

Step 8:

For Encapsulation Mode select the connection

protocol:

PPP over ATM VCMUX (RFC2364)

Click Apply

Click on the General tab

Step 9:

Under Line Status, the indication ADSL Connection

Established, indicates that the connection /

synchronization with the ADSL line has been done

with success.

Note: 1 to 2 minutes are required after you make

the above configurations, in order for the F200 to

be synchronized with the ADSL line.

Step 10:

To see information regarding the connection,

click the Physical Layer Statistics tab,

and click OK.

Double click on the Access Runner icon

ADSL Connection Established indicates that the

connection / synchronization with the ADSL line

has been done with success.

Note: After power on the PC, it takes 1 to 2 minutes

in order for the F200 to be synchronized

with the ADSL line.

3.6 Connection to the Internet

Step 1:

To connect to the Internet, double click on the

Connect Access Runner DSL icon which is found

on the Desktop

Step 2:

Insert the "User Login & Password" that has been

given to you by your ISP, click Dial to connect.

Step 3:

Double click on the connection icon on the Windows toolbar.

Step 4:

To ensure that the F200 has been successfully

installed, under the General tab, check to see that

Connected is indicated next to Status.

You can also check your connection

speed: Speed -> 448.0kbps.

Step 5:

Under the Details tab, you can see various

information regarding the connection.

(i.e. Server Type, Server IP address etc.).

4. Troubleshooting

The POWER LED is not on

ñCheck to see that the connections between the USB port of the F200 and the

USB port of your computer are plugged in correctly.

Cannot access ISP

ñIf in PPPoA & PPPoE mode, check your login account and password for the

remote server.

ñCheck your VPI/VCI value and encapsulation mode are the same as your ISP

gave you.

ñTry to dial the phone to check if the phone line to CO is good if telephone

service is available.

Note: Incase you take out the USB plug from your computer and plug it back

to the USB port of the computer again (does not matter if its upon shut-down

or while the computer is on), then the Annex selection will automatically be set

to Annex B. To set it back to Annex A, please follow the procedure of Step 5

of 3.5 Software Configuration.

Reset (reset connection)

Restart the connection of the F200 modem by pressing ‘Stop’ and ‘Start’ in

the first window example of section 3.5.

Note: Check to see if it is successful or not.

Declaration of Conformity

The 'F200 ADSL USB MODEM' is approved for use for within the European

Union, and the compatibility of this unit and it’s basic requirements are declared

with the CE symbol.

Passage extract of the authentic declaration of conformity:

CE Verification of Compliance

Technical Standards:

EMC: ETSI EN 300 386 v1.3.2/2002.12

LVD: EC LOW VOLTAGE DIRECTIVE 73/23/EEC, 93/68/EEC

Measurement standards:

(1) EN 55022 : 1998

(2) EN 61000-3-2: 2000

(3) EN 61000-3-3: 1995

(4) EN 61000-4-2: 1998

(5) EN 61000-4-3: 1998

(6) EN 61000-4-4: 1995

(7) EN 61000-4-5: 1995

(8) EN 61000-4-6: 1996

(9) EN 61000-4-11: 1994

(10) EN 60950 : 2000

Measurement Facilities: BEST LABORATORY CO., LTD.

Note: Specifications are subject to change without prior notice.

www.crypto.gr

Crypto F200 User manual

Brand: Crypto

Model: F200

Type: User manual

Download PDF

report

in other languages

italiano: Crypto F200 Manuale utente

Crypto F200 User manual

Crypto F200 User manual

in other languages

Related papers

Other documents