MECHANISM SERVICE
TECHNICAL INFORMATION
L54F4/US, XE
L5AE4/XE, US
FILE NO.
Dome type camera
REFERENCE No.MM5310481
VCC-9300
(Product code: 117 116 00)
(U.S.A.)
(Canada)
(Taiwan)
(Korea)
VCC-9300P
(Product code: 117 116 01)
(Europe)
VCC-9400P
(Product code: 117 119 00)
(Europe)
VCC-9400
(Product code: 117 119 01)
(U.S.A.)
(Canada)
(Taiwan)
(Korea)
–2–
CONTENTS
EXPLODED VIEWS
1. Exploded view of the Unit ..................................................................................................................................... 3
2. Exploded view of the Unit A ................................................................................................................................. 4
3. Exploded view of the Unit B ................................................................................................................................. 5
4. Exploded view of the Unit C ................................................................................................................................. 6
5. Exploded view of the Unit D ................................................................................................................................. 7
SERVICE TOOLS
Service tools................................................................................................................................................................ 8
DISASSEMBLY PROCEDURE OF MAIN PARTS
1. Removing Base unit .............................................................................................................................................. 9
2. Removing Rotation unit ........................................................................................................................................ 9
3. Removing Main board ass'y ............................................................................................................................... 10
4. Removing Power board ass'y ............................................................................................................................. 11
5. Removing Camera unit and Fan motor ass'y .................................................................................................... 12
6. Removing Slip ring ass'y .................................................................................................................................... 13
7. Removing Pan motor (Motor ass'y) ................................................................................................................... 14
8. Removing Pan belt (Synchro belt 140) and Synchro pulley (N132) ................................................................ 15
9. Removing Tilt motor (Motor ass'y) ..................................................................................................................... 16
10. Removing Tilt belt (Synchro belt (N180)) and Synchro pulley (N132) ............................................................ 17
11. Removing Bearing Tilt mechanism part ............................................................................................................ 18
12. Removing SY-1 Board ass'y (Compl pwb SY-1)............................................................................................... 19
13. Removing Power supply ..................................................................................................................................... 19
14. Removing Safefy wire ass'y ............................................................................................................................... 20
15. Disassembling Lock mechanism part ................................................................................................................ 20
REASSEMBLY PROCEDURE OF MAIN PARTS
1. Reassembling Slip ring ass'y ............................................................................................................................. 21
2. Reassembling Bearing (Tilt mechanism part) and Synchro pulley (N132) ..................................................... 22
3. Installing Slip ring ass'y ...................................................................................................................................... 24
4. Installing Pan motor (Motor ass'y) and Pan belt (Synchro belt 140) ............................................................... 25
5. Installing Tilt motor (Motor ass'y) and Tilt belt (Synchro belt 180) .................................................................. 26
6. Installing Camera cover ...................................................................................................................................... 27
7. Installing Frame B ............................................................................................................................................... 27
8. Installing Frame A and Supporter ...................................................................................................................... 28
9. Reassembling Camera unit ................................................................................................................................29
10. Installing Camera unit ......................................................................................................................................... 31
11. Installing Main board ass'y and Power board ass'y.......................................................................................... 32
12. Arranging Harness .............................................................................................................................................. 33
13. Installing Inner cover .......................................................................................................................................... 34
14. Installing the parts to Case................................................................................................................................. 35
15. Installing the parts to Base section .................................................................................................................... 37
16. Reassembling and Installing Power supply....................................................................................................... 40
17. Installing SY-1 board ass'y (Compl pwb SY-1) ................................................................................................. 42
18. Installing O-Ring to Base.................................................................................................................................... 44
19. Setting Switch of SY-1 board ass'y (Compl pwb SY-1)................................................................................... 44
20. Installing O-Ring to Clear dome ......................................................................................................................... 45
21. Installing Base unit and Main unit ...................................................................................................................... 45
22. Adjusting the tilt of Inner cover .......................................................................................................................... 46
23. Installing Clear come .......................................................................................................................................... 46
–3–
EXPLODED VIEWS
MAIN BOARD ASS'Y
RH M SCR. 2.6*4MM
BH SCR. 2*4MM
RH SCR. 2.6*3MM
RH SCR. 2.6*4MM
RH SW/W SCR. 3*10MM
O-RING
CLEAR DOME
INNER COVER
CAMERA COVER
Quantity
1
1
1
1
4
4
4
4
3
1
No.
6
5
28
60
101
104
103
102
117
201
Parts name
101
D
C
A
B
117
103
104
201
5
6
28 + 60
102
1. Exploded view of the Unit
–4–
2. Exploded view of the Unit A
107
31
5
22
23
17
106
20
4
156
63
9
102
155
15224
52
101
21
116
13
104
203
102
101
151
20
106
116
55
21
3
101
152
54
53
10
102
103
A
1
A
SYNCHRO PULLEY (N22)
SYNCHRO PULLEY (N132)
SHIM
SUPPORTER
CAMERA BASE
FRAME B
FRAME A
CAMERA COVER
T-HOLDER
MAIN FRAME
Quantity
1
1
1
1
1
1
1
1
2
2
No.
4
3
5
9
10
17
13
11
20
RH SCR. 2.6*4MM
RH SW/W SCR. 3*10MM
SYNCHRO BELT (140)
SYNCHRO BELT (180)
BEARING
LOCK NUT
SPACE COLLAR
T-SHAFT
RITINA
1
1
1
1
1
1
2
7
6
22
21
23
24
52
55
54
53
101
102
MOTOR ASS'Y
SLIP RING ASS'Y
SET SCR. 3*3MM
FH SCR. 3*8MM
FH SCR. 2.6*6MM
BH SCR. 2*4MM
RH SCR. 2.6*3MM
2
4
4
4
4
1
2
103
104
116
107
106
151
152
Parts name
–5–
3. Exploded view of the Unit B
Quantity
Parts name
1
1
2
FAN BRACKET
MAGNET BASE
CAMERA SUPPORT
MAGNET
1
1
10
2
RH SCR. 2.6*3MM
BH SCR. 2*4MM
FH SCR. 2*12MM
1
FAN MOTOR ASS'Y
CAMERA(300P)
1
1
FLEXIBLE FALT CABLE
I-F BOARD ASS'Y
1
No.
7
8
12
59
103
104
105
153
64
65
204
12
59
8
7
12
204
104
104
64
65
103
104
104
105
153
–6–
4. Exploded view of the unit C
CASE
1
Quantity
Parts name
1
1
MAGNET BASE
LOCK PLATE
CLEAR DOME
O-RING
MAGNET
RH SCR. 2.6*4MM
RATING LABEL
1
No.
8
15
28
60
59
102
29
2
1
1
1
1
102
15
8
59
102
1
29
60
28
–7–
Quantity
Parts name
1
1
1
1
1
1
1
BASE
PRESSURE PLATE
STOPPER PLATE
STOPPER
CORD BUSH
PACKING
INSULATION PLATE
POWER SUPPLY
O-RING
SPRING A
VENTILATION FILM
1
1
1
1
1
FERRITE CORE
2
2
4
1
2
8
2
FH SCR. 3*8MM
FH SCR. 3*10MM
RH SW/W SCR. 3*6MM
RH SCR. 2.3*10MM
BH SCR. 3*6MM
BH SCR. 3*12MM
DC NUT 3MM
WASHER 3.2*7*0.5MM
2
1
1
1
1
1
SAFETY WIRE ASS'Y
POWER/I-O CABLE ASS'Y
POWER SWITCH CABLE ASS'Y
RELAY/I-O CABLE ASS'Y
DC24V POWER CABLE ASS'Y
COMPOUND CABLE ASS'Y
MICRO SWITCH
RATING LABEL
1
I-O BOARD ASS'Y
1
No.
2
14
16
19
25
26
27
62
61
60
57
56
51
107
108
109
110
111
112
113
114
160
159
158
157
154
29
164
202
1
1
51
25
19
16
27
2
26
14
29
108
109
56
57
107
154
60
61
110
111
158
157
159
113
114
202
112
111
160
164
62
63
5. Exploded view of the unit D
–8–
SERVICE TOOLS
VHJ-0154
VHJ-0153
VHJ-0152
GUIDE WRENCH A
VHJ-0151
1
1
1
1
GUIDE WRENCH B
PULLEY JIG
EXTENSION CABLE
OIL COMPOUND
1
VHJ-0155
304
303
302
301
307
No.
Jig No.
Quantity
Parts name
301 302 303
304 307
–9–
1. Removing Base unit
1-1. Lift up on Stopper
19
from Base unit, then snap it to stop.
1-2. Turn Main unit counterclockwise 10 degree to remove Base unit from Main unit.
1-3. Remove Sefety wire ass'y
154
from Base unit.
1-3-1. Push Sefety wire ass'y
154
slightly while holding its end, then release it from locking.
1-3-2. Move Sefety wire ass'y
154
along with the groove.
1-3-3. Remove Sefety wire ass'y
154
from the hole of groove.
2. Removing Rotation unit
2-1. Turn Clear dome
28
counterclockwise 13 degree to remove.
2-2. Remove Screws
101
(x4) from the inside of Case
1
, then remove Rotation unit.
DISASSEMBLY PROCEDURE OF MAIN PARTS
Stopper
Base unit
Safey wire ass'y
Main unit
2
1
2
3
1
19
154
Figure of Step 1-1 through Step 1-3
Clear dome
Rotation unit
Case
Screws
3x10 mm (x4)
28
101
101
1
Figure of Steps 2-1 and 2-2
–10–
3. Removing Main board ass'y
3-1. Remove Screws
117
(x3) on Rotation unit, then remove Inner cover
6
.
This is the disassembly procedure after the disassembling of:
1. Removing Base unit: Page 9
2. Removing Rotation unit: Page 9
3-2. Removing Main board ass'y
3-2-1. Remove the connectors (x5) on Main board ass'y
201
.
3-2-2. Remove Screws
104
(x4), then remove Main board ass'y
201
.
Refer to Step 11-1 on page 32, Step 12-1 on page 33 and Step 13-1 on page 34 for reassembling.
Inner cover
Screws
2.6x4 mm (x3)
117
117
117
6
Figure of Step 3-1
Main board ass'y
1
2
3
4
5
Screws
2x4 mm (x4)
104
104
104
104
201
Figure of Step 3-2
–11–
4. Removing Power board ass'y
4-1. Removing Power board ass'y
4-1-1. Remove the connectors (x3) on Power board ass'y
203
.
4-1-2. Remove Screws
104
(x4), then remove Power board ass'y
203
.
This is the disassembling procedure after the disassembling of:
1. Removing Base unit: Page 9
2. Removing Rotation unit: Page 9
Refer to Step 11-2 on page 32 and Step 12-1 on page 33 for reassembling.
Power board ass'y
1
2
3
Screws
2x4 mm (x4)
104
203
104
Figure of Step 4-1
–12–
5. Removing Camera unit and Fan motor ass'y
5-1. Turn Camera cover
5
clockwise as far as possible.
5-2. Remove Screws
103
(x4), then remove Camera cover
5
.
This is the disassembling procedure after the disassembling of:
1. Removing Base unit: Page 9
2. Removing Rotation unit: Page 9
3. Removing Main board ass'y: Page 10
5-3. Remove Screws
102
(x4) to remove the connector on Camera unit, then remove Camera unit.
5-4. Remove the 2P connector on Fan motor ass'y
153
and remove Screws
105
(x2), then remove Fan motor ass'y
153
.
Refer to page 29 through page 34 for reassembling.
Camera cover
Screws
2.6x3 mm
(x4)
103
5
103
Figure of Steps 5-1 and 5-2
12
59
8
7
12
204
104
104
64
103
104
104
105
153
65
Camera unit
Screws
2.6x4 mm (x4)
Disassembly of Camera unit
102
102
102
Figure of Step 5-3
Screws
2x12 mm (x2)
105
105
Fun motor ass'y
153
2P connector
Figure of Step 5-4
–13–
6. Removing Slip ring ass'y
6-1. Remove Screws
107
(x4), then remove Camera base
11
and Camera cover
5
.
This is the disassembling procedure after the disassembling of:
1. Removing Base unit: Page 9
2. Removing Rotation unit: Page 9
3. Removing Main board ass'y: Page 10
5. Removing Camera unit and Fan motor ass'y: Page 12
6-2. Remove Pan belt (Synchro belt 140)
55
. Turn Pan belt (Synchro belt 140)
55
while lifting up on, so that you can
remove it easily.
6-3. Remove Frame B
10
and Binder
63
using nipper.
6-4. Remove Screws
102
(x2) and Screws
103
(x2), then remove Frame B
10
.
6-5. Remove Screws
101
(x3), then remove Slip ring ass'y
151
.
Refer to Step 3-1 on page 24, Step 4-2 through Step 4-4 on page 25, Steps 6-1 and 7-1 on page 27 and page 31
through page 34 for reassembling.
Camera cover
5
Camera base
11
Screws
3x8mm (x4)
107
107
Figure of Step 6-1
Screws
2.6x4 mm (x4)
102
Frame B
10
Binder
63
Slip ring ass'y
151
Pan belt (Synchro belt 140)
55
Binder
63
Screws
3x10 mm (x3)
101
101
103
Screws
2.6x3mm (x2)
103
Figure of Step 6-2
Figure of Step 6-4
Figure of Steps 6-3 and 6-4
–14–
7. Removing Pan motor (Motor ass'y)
7-1. Remove Pan belt (Synchoro belt 140)
55
. Turn Pan belt (Synchro belt 140)
55
while lifting up on, so that you can
remove it easily.
7-2. Remove the connector from Pan motor (Motor ass'y)
152
.
This is the disassembling procedure after the disassembling of:
1. Removing Base unit: Page 9
2. Removing Rotation unit: Page 9
7-3. Remove Binder
63
holding the cable of Pan motor (Motor ass'y)
152
using nipper.
7-4. Remove Screws
101
(x2), then remove Pan motor (Motor ass'y)
152
.
7-5. Remove Screws
116
(x2), then remove Synchro pulley (N22)
21
from Pan motor (Motor ass'y)
152
.
Refer to Step 4-1 through Step 4-4 on page 25 for reassembling.
Connector
to be removed
1
Pan belt
(Synchro belt 140)
55
Figure of Steps 7-1 and 7-2
Synchro pulley (N22)
21
Pan motor
(Motor ass'y)
152
Binder
63
Screws
3x10 mm (x2)
101
Figure of Step 7-3 through Step 7-5
–15–
8. Removing Pan belt (Synchro belt 140) and Synchro pulley (N132)
8-1. Remove Pan belt (Synchro belt 140)
55
. Turn Pan belt (Synchro belt 140)
55
while lifting up on, so that you can
remove it easily.
This is the disassembling procedure after the disassembling of:
1. Base unit: Page 9
2. Removing Rotation unit: Page 9
8-2. Remove Screws
106
(x2), then remove Synchro pulley (N132)
20
.
Refer to Step 1-4 on page 21 and Step 4-2 through Step 4-4 on page 25 for reassembling.
Connector
to be removed
1
Pan belt
(Synchro belt 140)
55
Figure of Step 8-1
Synchro pulley (N132)
20
Screws
2.6x6 mm (x2)
106
106
Figure of Step 8-2
–16–
9. Removing Tilt motor (Motor ass'y)
9-1. Remove Screws
107
(x4), then remove Camera base
11
and Camera cover
5
.
This is the disassembling procedure after the disassembling of:
1. Removing Base unit: Page 9
2. Removing Rotation unit: Page 9
3. Removing Main board ass'y: Page 10
4. Removing Power board ass'y: Page 11
5. Removing Camera unit and Fan motor ass'y: Page 12
9-2. Remove Tilt belt (Synchro belt (N180))
54
while turning.
9-3. Remove Screws
101
(x2), then remove Tilt motor (Motor ass'y)
152
.
Refer to Step 5-2 through Step 5-4 on page 26, Step 6-1 on page 27 and page 31 through page 34 for
reassembling.
Camera cover
5
Camera base
11
Screws
3x8mm (x4)
107
107
Figure of Step 9-1
Screws
3x10 mm (x2)
101
Tilt motor (Motor ass'y)
152
Tilt belt (Synchro belt (N180))
54
–17–
10. Removing Tilt belt (Synchro belt (N180)) and Syncro pulley (N132)
10-1. Remove Screws
107
(x4), then remove Camera base
11
and Camera cover
5
.
This is the disassembling procedure after the disassembling of:
1. Removing Base unit: Page 9
2. Removing Rotation unit: Page 9
3. Removing Main board ass'y: Page 10
4. Removing Power board ass'y: Page 11
5. Removing Camera unit and Fan motor ass'y: Page 12
10-2. Remove Tilt belt (Synchro belt (N180))
54
while turning.
10-3. Remove Screws
106
(x2), then remove Synhcro pulley (N132)
20
.
Refer to Step 5-2 through Step 5-4 on page 26, 6-1 on page 27 and page 31 through page 34 for reassembling.
Camera cover
5
Camera base
11
Screws
3x8mm (x4)
107
107
Figure of Step 10-1
Synchro pulley (N132)
20
Tilt belt (Synchro belt (N180))
54
Screws
2.6x6 mm (x2)
106
Figure of Steps 10-2 and 10-3
–18–
Guide wrench B
(VHJ-0152)
302
Lock nut
52
Shim
17
Space collar
T-Holder unit
24
Guide wrench A
(VHJ-0151)
301
Ritina
22
T-Holder
4
T-Shaft
23
Bearing
53
Figure of Steps 11-2 and 11-3
11. Removing Bearing Tilt mechanism part
11-1. Remove Camera cable
155
while bending the connector on the camera side 90 degree.
This is the disassembling procedure after the disassembling of:
1. Removing Base unit: Page 9
2. Removing Rotation unit: Page 9
3. Removing Main board ass'y: Page 10
5. Removing Camera unit and Fan motor ass'y: Page 12
6. Removing Slip ring ass'y (Step 6-1): Page 13
11-2. Remove Lock nut
52
using Guide wrench B
302
, then remove T-Holder unit.
11-3. Remove Ritina
22
on T-Holder unit using Guide wrench A
301
, then remove Bearing
53
(x2).
Guide wrench A: VHJ-0151
Guide wrench B: VHJ-0152
Refer to Page 22 through Page 23, Step 5-2 through Step 5-4 on page 26, Step 6-1 on Page 27 and page 31
through page 34 for reassembling.
Camera cable
155
Figure of Step 11-1
–19–
12. Removing SY-1 Board ass'y (Compl pwb SY-1)
12-1. Remove Screws
111
(x4) from Base 2.
12-2. Remove the five connectors on SY-1 board ass'y (Compl pwb SY-1)
202
, then remove SY-1 board ass'y (Compl pwb
SY-1)
202
.
This is the disassembling procedure after the disassembling of:
1. Removing Base unit: Page 9
Refer to page 42 through page 43 for reassembling.
13. Removing Power supply
13-1. Remove Screws
111
(x4) from Base
2
, then remove Power supply
61
.
13-2. Remove Insulation plate
27
.
13-3. Remove Screws
110
(x2), then remove Micro switch
62
.
13-4. Remove Power/ I-O cable ass'y 157.
This is the disassembling procedure after the disassembling of:
1. Removing Base unit: Page 9
12.Removing SY-1 Board ass'y (Compl pwb SY-1): Page 19
Refer to page 40 through page 43 for reassembling.
SY-1 board ass'y
(Compl pwb SY-1)
202
Screws
3x6 mm (x4)
1
5
4
3
2
Figure of Step 12-1
111
Base
2
111
111
Power/ I-O cable ass'y
157
Insulation plate
27
Screws
3x6 mm (x4)
Screws
2.3x10 mm
(x2)
110
110
Base
2
Power supply
61
Micro switch
62
111
111
Figure of Step 13-1 through Step 13-4
–20–
14. Removing Safety wire ass'y
14-1. Remove Screws
107
(x2) on Base
2
, then remove Safety wire ass'y
154
.
This is the disassembling procedure after the disassembling of:
1. Removing Base unit: Page 9
Refer to Step 15-2 on page 37 for reassembling.
15. Disassembling Lock mechanism part
15-1. Remove Screw
109
(x1), then remove Stopper plate
16
.
Note: Be carefull with Stopper
19
and Spring A
57
jumping out.
This is the disassembling procedure after the disassembling of:
1. Removing Base unit: Page 9
Refer to Step 15-1 through 15-2 on page 37 for reassembling.
Screws
3x8 mm
(x2)
107
Safety wire ass'y
154
Base
2
Figure of Step 14-1
Screw
3x6 mm (x1)
109
Stopper plate
16
Spring A
57
Stopper
19
Figure of Step 15-1
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/