Supermicro H8DGi-F User manual

Category
Server/workstation motherboards
Type
User manual

This manual is also suitable for

USER’S MANUAL
Revision 1.2a
®
SUPER
H8DGi
H8DGi-F
H8DG6
H8DG6-F
The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
and makes no commitment to update or to keep current the information in this manual, or to notify
any person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at
www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and
documentation, is the property of Supermicro and/or its licensors, and is supplied only under a
license. Any use or reproduction of this product is not allowed, except as expressly permitted by
the terms of said license.
IN NO EVENT WILL Super Micro Computer, Inc. BE LIABLE FOR DIRECT, INDIRECT, SPECIAL,
INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE
OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPER MICRO COMPUTER, INC. SHALL
NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED
WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING,
INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall be
the exclusive venue for the resolution of any such disputes. Supermicro's total liability for all claims
will not exceed the price paid for the hardware product.
FCC Statement: Refer to Supermicro's web site for FCC Compliance Information.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See
www.dtsc.ca.gov/hazardouswaste/perchlorate”.
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.
Manual Revision 1.2a
Release Date: March 06, 2014
Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2014 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America
Preface
iii
Preface
About This Manual
This manual is written for system integrators, PC technicians and knowledgeable
PC users. It provides information for the installation and use of the H8DG6/i(-F)
serverboard.
The H8DG6/i(-F) serverboard is based on the AMD® Dual SR5690 and one SP5100
chipset and supports two AMD Socket G34 type processor with up to 128 GB of
ECC/Non-ECC UDIMM or 512 GB of ECC RDIMM. This board series includes the
following serverboards and characteristics:
Serverboard Embeded IPMI Onboard SAS2
H8DG6 Yes
H8DGi
H8DG6-F Yes Yes
H8DGi-F Yes
Please refer to the motherboard speci cations pages on our web site for updates on
supported processors (http://www.supermicro.com/aplus/). This product is intended
to be professionally installed.
Manual Organization
Chapter 1 includes a checklist of what should be included in your motherboard
box, describes the features, speci cations and performance of the motherboard
and provides detailed information about the chipset.
Chapter 2 begins with instructions on handling static-sensitive devices. Read this
chapter when installing the processor(s) and memory modules and when installing
the motherboard in a chassis. Also refer to this chapter to connect the hard disk
drives, the various ports, and the power and reset buttons and the system LEDs.
If you encounter any problems, see Chapter 3, which describes troubleshooting
procedures for the video, the memory and the setup con guration stored in CMOS.
For quick reference, a general FAQ (Frequently Asked Questions) section is
provided. Instructions are also included for contacting technical support. In addition,
you can visit our web site for more detailed information.
Chapter 4 includes an introduction to BIOS and provides detailed information on
running the CMOS Setup utility.
Appendix A provides BIOS Error Beep Code Messages.
Appendix B lists BIOS POST Checkpoint Codes.
iv
Table of Contents
Chapter 1 Introduction
1-1 Overview .........................................................................................................1-1
Checklist ..........................................................................................................1-1
1-2 Contacting Supermicro ....................................................................................1-2
H8DG6/i(-F) Quick Reference ......................................................................... 1-5
1-3 Motherboard Features .....................................................................................1-7
1-4 Chipset Overview ..........................................................................................1-10
AMD SR5690/SP5100 Chipset .....................................................................1-10
HyperTransport Technology .......................................................................... 1-10
1-5 PC Health Monitoring .................................................................................... 1-10
1-6 Power Con guration Settings.........................................................................1-11
1-7 Power Supply ................................................................................................1-12
1-8 Super I/O .......................................................................................................1-13
Chapter 2 Installation
2-1 Standardized Warning Statements ................................................................. 2-1
About Standardized Warning Statements .......................................................2-1
2-2 Static-Sensitive Devices ..................................................................................2-4
Precautions ..................................................................................................... 2-4
Unpacking ....................................................................................................... 2-4
2-3 Processor and Heatsink Installation................................................................ 2-5
2-4 Mounting the Motherboard into a Chassis ......................................................2-7
2-5 Installing Memory ............................................................................................2-7
DIMM Module Population Con guration ....................................................2-9
2-6 PCI Expansion Cards ....................................................................................2-10
2-7 I/O Port and Control Panel Connections .......................................................2-11
Front Control Panel ........................................................................................2-11
2-8 Connector De nitions ................................................................................... 2-12
2-9 Jumper Settings ............................................................................................2-19
Explanation of Jumpers ................................................................................ 2-19
2-10 Onboard Indicators ........................................................................................2-22
2-11 SAS and SATA Drive Connections ............................................................... 2-24
2-12 Enabling SATA RAID ..................................................................................... 2-25
Serial ATA (SATA)..........................................................................................2-25
Installing the OS/SATA Driver .......................................................................2-25
Building a Driver Diskette ......................................................................... 2-25
Enabling SATA RAID in the BIOS ................................................................. 2-26
Table of Contents
v
Using the DotHill and Adaptec RAID Utility .................................................. 2-28
Installing the RAID Driver During OS Installation .........................................2-28
2-13 Installing Drivers ............................................................................................2-29
Supero Doctor III ...........................................................................................2-30
2-14 Serverboard Battery ......................................................................................2-32
Chapter 3 Troubleshooting
3-1 Troubleshooting Procedures ........................................................................... 3-1
Before Power On ............................................................................................ 3-1
No Power ........................................................................................................3-1
No Video .........................................................................................................3-2
Memory Errors ............................................................................................... 3-2
Losing the System’s Setup Con guration ....................................................... 3-2
3-2 Technical Support Procedures ........................................................................3-2
3-3 Frequently Asked Questions ........................................................................... 3-3
3-4 Returning Merchandise for Service................................................................. 3-4
Chapter 4 BIOS
4-1 Introduction ......................................................................................................4-1
4-2 Main Menu ...................................................................................................... 4-2
4-3 Advanced Settings Menu ................................................................................ 4-2
4-3 Security Menu ...............................................................................................4-15
4-4 Boot Menu ..................................................................................................... 4-16
4-5 Exit Menu ......................................................................................................4-17
Appendix A BIOS Error Beep Codes
Appendix B BIOS POST Checkpoint Codes
B-1 Uncompressed Initialization Codes .................................................................B-1
B-2 Bootblock Recovery Codes .............................................................................B-2
B-3 Uncompressed Initialization Codes .................................................................B-3
H8DG6/i(-F) SERVERBOARD USER'S MANUAL
Notes
Table of Contents
vi
Chapter 1: Introduction
1-1
Chapter 1
Introduction
1-1 Overview
Checklist
Congratulations on purchasing your computer motherboard from an acknowledged
leader in the industry. Supermicro boards are designed with the utmost attention to
detail to provide you with the highest standards in quality and performance.
Please check that the following items have all been included with your motherboard.
If anything listed here is damaged or missing, contact your retailer.
One (1) H8DG6/i(-F) serverboard
One (1) I/O shield (MCP-260-00027-0N)
One (1) 9-pin serial port cable (CBL-0010L)
One (1) 15.7-inch USB 2.0 2-Port with Key cable (CBL-0083L)
Two (2) 50-cm I-Pass to four SATA PBF cables (CBL-0097L-02) (for H8DG6
and H8DG6-F only)
Four (4) 2ft. Amphenol, SATA cable (CBL-0044L) (Six for H8DGi or H8DGi-F)
Note: For your system to work properly, please follow the links below to download
all necessary drivers/utilities and the user’s manual for your motherboard.
Supermicro product manuals: http://www.supermicro.com/support/manuals/
Product drivers and utilities: ftp://ftp.supermicro.com
Product safety information:
http://super-dev/about/policies/safety_information.cfm
If you have any questions, please contact our support team at:
support@supermicor.com
1-2
H8DG6/i(-F) SERVERBOARD USER'S MANUAL
1-2 Contacting Supermicro
Headquarters
Address: Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: +1 (408) 503-8000
Fax: +1 (408) 503-8008
Email: [email protected] (General Information)
[email protected] (Technical Support)
Web Site:
www.supermicro.com
Europe
Address: Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel: +31 (0) 73-6400390
Fax: +31 (0) 73-6416525
Email: [email protected] (General Information)
[email protected] (Technical Support)
[email protected] (Customer Support)
Web Site:
www.supermicro.com
Asia-Paci c
Address: Super Micro Computer, Inc.
3F, No. 150, Jian 1st Rd.
Zhonghe Dist., New Taipei City 235
Taiwan (R.O.C)
Tel: +886-(2) 8226-3990
Fax: +886-(2) 8226-3992
Tel: +886-(2)-8226-3990
Web Site:
www.supermicro.com.tw
Chapter 1: Introduction
1-3
Figure 1-1. H8DG6/i(-F) Image
1-4
H8DG6/i(-F) SERVERBOARD USER'S MANUAL
Notes:
Jumpers not indicated are for test purposes only.
Not all ports, jumpers or LED Indicators are available on all serverboards.
Figure 1-2. H8DG6/i(-F) Motherboard Layout
(not drawn to scale)
LE1
BATTERY
JOH1
JI2C2
JI2C1
JPL1
JPG1
JWD1
JPS1
JPB1
DP3
LEDS1
DP1
JBT1
JIBTN1
T-SGPIO2T-SGPIO1
JWOL1
1
JSMB1
JTPM1
JWF1
JD1
JF1
FAN4
FAN3
FAN2
FAN5
FAN7/CPU1
FAN1
FAN6
FAN8/CPU2
JPI2C1
SAS 4~7
JPW1 JPW3 JPW2
BMC
Windbond
COM1
SLOT6 PCI-E 2.0 X16
SLOT5 PCI-E 2.0 X4 (IN X8)
COM2
USB7USB6
USB2/3
USB4/5
SATA0
SATA1
SATA2
SATA3
SATA4
SATA5
KB/MOUSE
USB0/1
IPMI_LAN
LAN1
LAN2
CPU1
CPU2
P2-DIMM1A
P2-DIMM1B
P2-DIMM2A
P2-DIMM2B
P2-DIMM3A
P2-DIMM3B
P2-DIMM4A
P2-DIMM4B
P1-DIMM4B
P1-DIMM4A
P1-DIMM3B
P1-DIMM3A
P1-DIMM2B
P1-DIMM2A
P1-DIMM1B
P1-DIMM1A
UID
SLOT2 PCI-E 2.0 X16
SLOT1 PCI-E 2.0 X4 (IN X8)
SLOT4 PCI-E 2.0 X16
SLOT3 PCI-E 2.0 X8
VGA
AMD
SP5100
AMD
SR5690
AMD
SR5690
LSI
2008
SAS2
INTEL
82576
SAS 0~3
JL1
Chapter 1: Introduction
1-5
H8DG6/i(-F) Quick Reference
Jumper Description Default Setting
JBT1 CMOS Clear (See Section 2-7)
JI2C1/JI2C2 I2C to PCI-E Slot Enable/Disable Both Open (Disabled)
JPB1 BMC Enable/Disable Pins 1-2 (Enabled)
JPG1 VGA Enable/Disable Pins 1-2 (Enabled)
JPL1 LAN 1 Enable/Disable Pins 1-2 (Enabled)
JPS1 SAS Controller Enable/Disable Pins 1-2 (Enabled)
JWD1 Watch Dog Pins 1-2 (Reset)
LED Description
LAN Ports LEDs for the LAN Ethernet ports
Dedicated IPMI LAN LEDs for the dedicated IPMI LAN Ethernet port (H8DGi/6-F only)
DP1 LED for BMC Heartbeat
DP3 LED for Serverboard Power-On
LE1 LED for UID Button
LEDS1 SAS2008 Heartbeat LED
1-6
H8DG6/i(-F) SERVERBOARD USER'S MANUAL
Connector Description
COM1/COM2 COM1 Serial Port/Header
FAN 1-8 Chassis/CPU Fan Headers
IPMI LAN Dedicated IPMI LAN Port (H8DGi/6-F only)
JD1 Speaker Header
JF1 Front Panel Connector
JIBTN1 RAIDKey for RAID 5 SAS support (optional for H8DG6(-F) only)
JL1 Chassis Intruder Header
JOH1 Overheat Warning Header
JPI2C1 Power I
2
C Header
JPW1 24-pin Main ATX Power Connector
JPW2/3 +12V 8-pin CPU Power Connectors
JTPM1 Trusted Platform Module Header
JSMB1 System Management Bus Header (SMBus)
JWF1 SATA DOM (Disk_On_Module) PWR
JWOL1 Wake-On-LAN Header
LAN1/2 Gigabit Ethernet (RJ45) Ports
PS2 Mouse/Keyboard PS2 Mouse/Keyboard connectors
SAS0~3, SAS4~7 SAS Ports (H8DG6(-F) only)
SATA0 ~ SATA5 SATA Ports
T-SGPIO1/T-SGPIO2 Serial General Purpose Input/Output Header for SATA
USB0/1, USB2/3, USB4/5, USB6/7 Universal Serial Bus (USB) Ports, Headers and Type-A Ports
VGA VGA Connector
Chapter 1: Introduction
1-7
1-3 Motherboard Features
CPU
Dual AMD Opteron 6000 series (AMD Socket G34 type) processor
Note: Refer to our web site for details on supported processors.
Memory
Sixteen (16) four channel DIMM slots support up to 128 GB of ECC/Non-ECC
UDIMM or 512 GB of ECC RDIMM, with DDR3-1600/1333/1066 Mhz speed
SDRAM in 1 GB, 2 GB, 4 GB, 8 GB, 16 GB or 32 GB sizes of 1.5V or 1.35V
voltages.
Note: Refer to Section 2-5 before installing memory and our web site for recommended DIMMs.
Chipset
Dual AMD SR5690 chipsets and one SP5100 Southbridge chipset
Expansion Slots
Three (3) PCI-Express x16 Gen. 2
One (1) PCI-Express x8 Gen. 2
Two (2) PCI-Express x4 (in x8 slot) Gen. 2
BIOS
16 Mb AMIBIOS
®
SPI Flash ROM
DMI 2.3, PCI 2.2, ACPI 1.0 (ACPI 2.0 is BIOS supported), SMBIOS 2.3, Real
Time Clock Wakeup, Plug and Play (PnP), BIOS resume hot keys, Hardware
BIOS Virus Protection
PC Health Monitoring
Onboard voltage monitors
Fan status monitor with rmware/software on/off and speed control
Watch Dog
Environmental temperature monitoring via BIOS
Power-up mode control for recovery from AC power loss
System resource alert (via included utility program)
Auto-switching voltage regulator for the CPU core
CPU thermal trip support
I
2
C temperature sensing logic
Chipkill Support
1-8
H8DG6/i(-F) SERVERBOARD USER'S MANUAL
ACPI Features
Microsoft OnNow
Slow blinking LED for suspend state indicator
BIOS support for USB keyboard
Wake-On-LAN (WOL)
Onboard I/O
Six (6) SATA ports supported by an on-chip SATA controller (RAID 0, 1 and 10
supported)
Eight (8) SAS ports supported by an SAS2008 SAS2 controller (RAID 0, 1 and 10
supported; Raid 5 Optional) (H8DG6 and H8DG6-F only)
Eight (8) USB (Universal Serial Bus 2.0) ports (2x rear, 2x headers (USB 2/3
and USB 4/5), 2x type A)
Two (2) LAN ports supported by one onboard Intel® 82576 Ethernet controllers
for 10/100/1000Base-T
One (1) dedicated IPMI LAN port (H8DG6/i-F only)
One (1) VGA port supported by an onboard Matrox
®
G200 graphics controller
(with 16 MB DDR2 memory)
Two COM Ports (one external serial port, one Fast UART 16550 port)
Other
Onboard power LED
Chassis intrusion detection
CD Utilities
BIOS ash upgrade utility
Super Doctor III
IPMI 1.5 / 2.0
Dimensions
Extended-ATX form: (LxW) 12" x 13" (305 x 330 mm)
Chapter 1: Introduction
1-9
8x DIMM
LPC BUS
KEYBOARD/
MOUSE
8x DIMM
FWH
G34-SOCKET #2
LPC SIO
W83627DHG-P
AMD
SR5690#1
PCIE (X16)
PCIE (X8)
H/W_MONITOR
W83795
FAN
CONN. (8)
SATA PORT X6
SATA
SLOT#1
PCIE_(X4)
VRM
VRM
SLOT#6
PCIE_(X16)
HT Link
16/16-2.6GHz
SLOT#4
PCIE_(X16)
SLOT#3
PCIE_(X8)
HT Link
16 x16
b
it
s 6.4GHz
USB
USB PORT X8
LSI
SAS2 2008
PCIE (X8)
LAN
Intel 82576
PCIE (x4)
AMD
SP5100
Winbond
WPCM450
VGA
HT Link
AMD
SR5690#2
16/16-2.6GHz
DDR3
1600/1333/1066
PCIE (X4)
SLOT#5
PCIE_(X4)
G34-SOCKET #1
SLOT#2
PCIE_(X16)
DDR3
1600/1333/1066
Figure 1-3. AMD Dual SR5690 and one SP5100 Chipset:
System Block Diagram
Note: This is a general block diagram and may not exactly represent
the features on your motherboard. See the previous pages for the
actual speci cations of your motherboard.
1-10
H8DG6/i(-F) SERVERBOARD USER'S MANUAL
1-4 Chipset Overview
The H8DG6/i(-F) serverboard is based on the AMD Dual SR5690 and one SP5100
chipset. This chipset functions as a Media and Communications Processor (MCP).
Controllers for the system memory are integrated directly into AMD Opteron
processors.
AMD SR5690/SP5100 Chipset
The AMD Dual SR5690 and one SP5100 are each a single-chip, high-performance
HyperTransport peripheral controller. It includes a 42-lane PCI Express interface, an
AMD Opteron 16-bit Hyper Transport interface link, a six-port Serial ATA interface
and an eight-port USB 2.0 interface. This hub connects directly to the CPU.
HyperTransport Technology
HyperTransport technology is a high-speed, low latency point to point link that was
designed to increase the communication speed by a factor of up to 48x between
integrated circuits. This is done partly by reducing the number of buses in the
chipset to reduce bottlenecks and by enabling a more ef cient use of memory
in multi-processor systems. The end result is a signi cant increase in bandwidth
within the chipset.
1-5 PC Health Monitoring
This section describes the PC health monitoring features of the H8DG6/i(-F)
serverboard. The serverboard has an onboard System Hardware Monitor chip that
supports PC health monitoring.
Onboard Voltage Monitors
The onboard voltage monitor will continuously scan crucial voltage levels. Once
a voltage becomes unstable, it will give a warning or send an error message to
the screen. Users can adjust the voltage thresholds to de ne the sensitivity of the
voltage monitor. Real time readings of these voltage levels are all displayed in BIOS.
Fan Status Monitor with Firmware/Software Speed Control
The PC health monitor can check the RPM status of the cooling fans. The onboard
fans are controlled by thermal management via BIOS.
Chapter 1: Introduction
1-11
CPU Overheat/Fan Fail LED and Control
This feature is available when the user enables the CPU overheat/Fan Fail warning
function in the BIOS. This allows the user to de ne an overheat temperature. When
this temperature is exceeded or when a fan failure occurs, the Overheat/Fan Fail
warning LED is triggered.
Auto-Switching Voltage Regulator for the CPU Core
The 6-phase-switching voltage regulator for the CPU core can support up to
AMD Opteron 6000SE series processors and auto-sense voltage IDs ranging from
0.8 V to 1.55V. This will allow the regulator to run cooler and thus make the system
more stable.
1-6 Power Con guration Settings
This section describes the features of your motherboard that deal with power and
power settings.
Microsoft OnNow
The OnNow design initiative is a comprehensive, system-wide approach to system
and device power control. OnNow is a term for a PC that is always on but appears
to be off and responds immediately to user or other requests.
Slow Blinking LED for Suspend-State Indicator
When the CPU goes into a suspend state, the chassis power LED will start blinking
to indicate that the CPU is in suspend mode. When the user presses any key, the
CPU will wake-up and the LED will automatically stop blinking and remain on.
BIOS Support for USB Keyboard
If a USB keyboard is the only keyboard in the system, it will function like a normal
keyboard during system boot-up.
Note: To wake up the system from an S4 state by the USB keyboard/mouse, please
connect the keyboard/mouse to USB port 0/1 at the rear I/O side.
1-12
H8DG6/i(-F) SERVERBOARD USER'S MANUAL
Main Switch Override Mechanism
The power button can function as a system suspend button. When the user
depresses the power button, the system will enter a SoftOff state. The monitor
will be suspended and the hard drive will spin down. Depressing the power button
again will cause the whole system to wake-up. During the SoftOff state, the power
supply provides power to keep the required circuitry in the system alive. In case the
system malfunctions and you want to turn off the power, just depress and hold the
power button for 4 seconds. The power will turn off and no power will be provided
to the motherboard.
Wake-On-LAN (WOL)
Wake-On-LAN is de ned as the ability of a management application to remotely
power up a computer that is powered off. Remote PC setup, up-dates and access
tracking can occur after hours and on weekends so that daily LAN traf c is kept
to a minimum and users are not interrupted. The motherboard has a 3-pin header
(WOL) to connect to the 3-pin header on a Network Interface Card (NIC) that has
WOL capability. Wake-On-LAN must be enabled in BIOS.
1-7 Power Supply
As with all computer products, a stable power source is necessary for proper and
reliable operation. It is even more important for processors that have high CPU
clock rates.
The H8DG6/i(-F) serverboard requires the use of proprietary power supplies. Please
refer to the pinout information for the power connectors in Section 7 of Chapter 2
for detailed information on power requirements.
In areas where noisy power transmission is present, you may choose to install a
line lter to shield the computer from noise. It is recommended that you also install
a power surge protector to help avoid problems caused by power surges.
Warning: To prevent the possibility of explosion, do not use the wrong type of
onboard CMOS battery or install it upside down.
Chapter 1: Introduction
1-13
1-8 Super I/O
The disk drive adapter functions of the Super I/O Winbond® BMC chip includes a
data separator, write pre-compensation circuitry, decode logic, data rate selection,
a clock generator, drive interface control logic and interrupt and DMA logic. The
wide range of functions integrated onto the Super I/O greatly reduces the number
of components required for interfacing with oppy disk drives.
The Super I/O provides two high-speed, 16550 compatible serial communication
ports (UARTs), one of which supports serial infrared communication. Each UART
includes a 16-byte send/receive FIFO, a programmable baud rate generator,
complete modem control capability and a processor interrupt system. Both UARTs
provide legacy speed with baud rate of up to 115.2 Kbps as well as an advanced
speed with baud rates of 250 K, 500 K, or 1 Mb/s, which support higher speed
modems.
The Super I/O provides functions that comply with ACPI (Advanced Con guration
and Power Interface), which includes support of legacy and ACPI power management
through a SMI or SCI function pin. It also features auto power management to reduce
power consumption.
The IRQs, DMAs and I/O space resources of the Super I/O can be exibly adjusted
to meet ISA PnP requirements, which support ACPI and APM (Advanced Power
Management).
1-14
H8DG6/i(-F) SERVERBOARD USER'S MANUAL
Notes
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82

Supermicro H8DGi-F User manual

Category
Server/workstation motherboards
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI