VEHS-S1 User Guide
For use with Snom™ 300/800 and 700 series phones*
1. VXi warrants that your product will be free from defects in material and workmanship for one year from
the date of purchase. If, during that period from the date of purchase, your product fails to work due to
a defect in material or workmanship, VXi will repair or replace the product, at its election, free of charge.
Without proof of purchase, the warranty period begins on the date of manufacture. Consumable
components (for example, cushion, battery and fuse) are not included in this warranty.
2. The foregoing limited warranty does not cover equipment failure attributable to accident, improper operation,
misuse, abuse, or any cause other than defects in the materials or workmanship of VXi’s products.
3. VXi’s obligations under this warranty are limited to repair or replacement (at our option) of any defective part
returned to VXi at the customer’s expense. Returned products require a Return Authorization that may be
obtained by calling 800-742-8588. Products returned to VXi for repair under this warranty will be return
shipped to the customer at VXi’s expense.
4. THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Some jurisdictions
do not permit the exclusion of implied warranties and the foregoing exclusions may not apply to you.
5. In no event shall VXi be responsible for any other damages whatsoever, including direct, indirect, special,
incidental, consequential, or other damages for breach of this or any other warranty, express or implied.
VXi LIMITED WARRANTY
VXi Corporation | 271 Locust Street, Dover, NH 03820 USA
Toll Free | Sans frais | Número gratuito: (800) 742-8588
Phone | Téléphone | Teléfono: 1 603 742-2888
www.vxicorp.com
© 2013 VXi Corporation. All other trademarks are property of their respective owners.
Printed in China | Imprimé en Chine | Impreso en China
APN 203427B
INSTALLATION
1. Remove the panel from the bottom of
the base station (refer to the V150
User Guide for additional information).
2. Attach the VEHS-S1 to the bottom of
the V150 by carefully inserting the
plastic guide pin into the screw-hole
s
ocket on the base of the V150, then
g
ently press together the rear of the
V150 base and VEHS-S1 until it
snaps into place.
3. Insert the color-coded cables from
the VEHS-S1 into the corresponding
color-coded jacks of the V150 base
s
tation; the connectors should ‘snap’
i
n place when fully inserted.
4. Select the correct adapter cable
(included) and connect it to the
l
onger VEHS-S1 cable. Connect the
o
pposite end to the AUX/EHS port on
the phone.
Additional V150 Setup
-
V150 should be in MODE 2.
- V150 ‘Compatibility Switch’ should be
placed in the ‘D” position.
L
ED Status Indicator
The LED status indicator indicates the
phone’s mode as shown by the table
below.
Phone Mode
300 Series
800 Series
700 Series
Cable
A
B
C
Connection Port
AUX
EHS
*This user guide describes the installation steps to connect the VEHS to your phone. For information about your
phone’s capabilities or provisioning requirements go to www.vxicorp.com/resources/vehs, visit your phone system
manufacturer’s website, or contact your IT administrator.
*Le manuel de l’utilisateur décrit les étapes de branchement du VEHS à votre téléphone.Pour des
renseignements sur les capacités de votre téléphone ou sur les exigences en matière d’approvisionnement, visitez le
www.vxicorp.com/resources/vehs ou le site Web du fabricant de votre téléphone, ou communiquez avec votre
administrateur TI.
*Esta guía de usuario describe los pasos de instalación para conectar el VEHS a su teléfono.Para obtener información
sobre las capacidades de su teléfono o requerimientos de provisiones visite www.vxicorp.com/resources/vehs, visite
el sitio web del fabricante del sistema de su teléfono o comuníquese con su administrador TI.
**Included with VEHS-S1+700 only.
**
P
hone Mode
O
n-hook
Off-hook
I
ncoming ring detected
L
ED indicator
S
olid on
Slow flash
F
ast flash