Aventura FBR-1GE2LX-SFP User manual

Brand: Aventura

Model: FBR-1GE2LX-SFP

Category: Network media converters

Type: User manual

AventuraTechnologies

180AdamsAvenue

Hauppauge,NY11788

(877)707‐9600

www.aventuratechnologies.com

Instruction Manual

SFP Based, 10/100/1000 Ethernet, 3-Port Unmanaged Switch /

Media Converter

Model Numbers:

FBR-1GE2LX-SFP – SFP Based, 10/100/1000 Mbps Ethernet, 3-Port Unmanaged Switch

/ Media Converter

INSTALLATION AND OPERATION INSTRUCTIONS

FUNCTIONAL DESCRIPTION

The FBR-1GE2LX-SFP is a three-port unmanaged switch, with one UTP 10/100/1000 Ethernet

interface and two SFP based optical interfaces. The FBR-1GE2LX-SFP is ideal for optical daisy-chain

applications as an add-drop multiplexer, where multiple devices, such as IP cameras, share a single fiber

link. The unit uses industry standard Small Form-Factor, Pluggable (SFP) modules for connecting to the

fiber media. Proper Aventura Technologies approved SFP modules are selected by the customer to

accommodate the type and number of fibers, as well as the transmission distance for each link.

The FBR-1GE2LX-SFP converts a single 10/100/1000base-T/TX Ethernet input to an optical fiber

output and transmits it over one of the two fiber links, based on the address of the destination device.

The FBR-1GE2LX-SFP converts any packet received from either optical link and addressed to the IP

address of a device connected to the unit’s UTP port, to a single 10/100/1000base-T/TX Ethernet output.

The FBR-1GE2LX-SFP also passes through any packet received from either fiber link to the other fiber

link, based on the destination address.

The FBR-1GE2LX-SFP is configured to auto-negotiate the data rate on the UTP Ethernet port to either

10, 100, or 1000 Mbps and operating mode to either full or half-duplex. Additionally, the unit is

configured to perform the MDI/MDIX sensing and switching automatically. This feature allows for the

use of standard, straight through patch cords, without regard to the configuration (MDI or MDIX) of the

device the FBR-1GE2LX-SFP unit is connected to.

The data rate on the optical port of the FBR-1GE2LX-SFP is always 1000Mbps, full-duplex.

The FBR-1GE2LX-SFP can operate with two different SFP modules at the same time. This feature

allows the unit to interconnect two different fiber infrastructure types (e.g. convert a single fiber,

multimode, connection to a two-fiber, single mode connection.)

This unit is contained in a compact and rugged steel housing with internal dc voltage regulation. The

detachable terminal block and LED indicators provide for easy installation and monitoring of Ethernet,

optical link, and dc power status.

The unit operates as either a surface mounted, modular, stand-alone device, or within a rack mounted

card cage.

INSTALLATION

THE INSTALLATION OF THIS UNIT SHOULD BE MADE BY A QUALIFIED SERVICE

PERSON(S) AND MUST CONFORM TO ALL LOCAL CODES.

The physical outline and front/rear panel configuration of the unit is detailed in Figure 2.

Mount the unit to a secure surface using #8 (3mm) hardware in two places. See Figure 3 for a full size

mounting template. Be sure to allow sufficient room for the required minimum bend radius of the fiber

cable used.

POWER SOURCE

The unit requires a +12VDC power source for proper operation. The DC input is diode protected against

reverse polarity connection.

In the USA and in Canada, for standalone surface mounted installation, an Aventura Technologies FBR-

PSUS12DC1A is supplied with this unit. Contact Aventura Technologies for ordering power supply

units for use in countries other than the USA and Canada.

When installed in a rack mounted card cage, the power for the unit is supplied from the card cage’s

power supply.

POWER CONNECTION

Power is supplied to the unit via a two-pin terminal block connector. Follow the labeling on the unit for

proper connections of the +12 volt dc and ground leads.

ETHERNET CONNECTION

The UTP Ethernet connection is made via an RJ-45 connector on the front of the unit. For proper

operation, the use of a patch cord and/or cable rated Category-5e or better is required.

FIBER CONNECTION

There are two SFP module slots on the front of the unit. The fiber optic connections vary, depending on

the selection of SFP module. Refer to the instructions supplied with the SFP modules for the proper

procedure of installing the SFP modules in the FBR-1GE2LX-SFP unit, as well as for the proper

procedure for connecting the fibers to the SFP modules.

STATUS INDICATORS

Each unit provides the following LED status indicators to aid in installation and troubleshooting:

POWER INDICATOR

A bi-color LED indicator monitors the voltage at the unit’s input connector and the operating internal

voltage of the module. The power status associated with this indicator is summarized below.

Power Indicator Power Status

Green Proper Input Voltage Present – Proper Internal Operating Voltage Present

Red Proper Input Voltage Present – Internal Operating Voltage Faulty

Off No Input Voltage Detected

OPTICAL LINK INDICATOR

A bi-color LED indicator for each SFP interface monitors the power of, and proper synchronization with

the optical input signal that is being received at the FBR-1FE1FX-SFP. The optical link status

associated with these indicators is summarized below.

Optical Link Indicator Optical Status

Green Proper Optical Input Present

Red Optical Input Not Detected

Off Check Power Supply

ETHERNET INDICATORS

Two LED indicators on the RJ-45 connector of the FBR-1GE2LX-SFP unit monitor the status and

operating mode of the UTP Ethernet link. The Ethernet status associated with these indicators is

summarized below.

Ethernet Indicators Ethernet Status

Speed

(Bi-Color)

Lit Amber: Link operating at 1000Mbps

Lit Green: Link operating at 100Mbps

Unlit: link operating at 10Mbps or no link

Link/Activity

(GREEN)

Lit: Good link on the port

Blinking: The port is receiving/transmitting data

Unlit: No link

Device Compatible With

FBR-1GE2LX-SFP FBR-1GE1LX-SFP-MINI

FBR-1GE1LX-SFP

FBR-2X1GE1LX-SFP

FBR-1GE2LX-SFP

FBR-8FE1LX-SFP

Figure 1 – List of Compatible Devices

Figure 2 – Physical Outline And Front/Rear Panel Configuration Of Units

Figure 3 – Surface Mounting Template (1:1)

LIMITED LIFETIME WARRANTY INFORMATION

This limited lifetime warranty applies only to the original end user customer of the product for so long

as the original end user customer owns the product. This limited warranty is non-transferable.

Damage due to shipping the products to you is covered under this limited warranty. Otherwise, this

limited warranty does not cover damage due to external causes, including accident, abuse, misuse,

problems with electrical power, servicing not authorized by Aventura Technologies, Inc., usage not in

accordance with product instructions, failure to perform required preventive maintenance, and problems

caused by use of parts and components not supplied by Aventura Technologies, Inc.

During the warranty period beginning on the invoice date, Aventura Technologies, Inc. will repair or

replace products covered under this limited warranty that are returned to Aventura Technologies, Inc.'s

facility. To request limited warranty service, you must contact Aventura Technologies, Inc.'s Customer

Technical Support within the limited warranty period. Refer below to find the appropriate contact

information for obtaining customer assistance. If limited warranty service is required, Aventura

Technologies, Inc. will issue a Return Material Authorization Number. You must ship the products back

to Aventura Technologies, Inc. in their original or equivalent packaging, prepay shipping charges, and

insure the shipment or accept the risk of loss or damage during shipment. Aventura Technologies, Inc.

will ship the repaired or replacement products to you freight prepaid if you use an address in the

continental United States, where applicable. Shipments to other locations will be made freight collect.

To view the full terms of the warranty, please go to: www.ati247.com

SERVICE INFORMATION

There are no user serviceable parts inside the unit.

In the event that service is required to this unit, please direct all inquiries to:

Aventura Technologies, Inc.

180 Adams Avenue Phone: (631) 300-4000

Hauppauge, NY 11788 FAX (631) 434-7000

E-mail:

[email protected]

Aventura FBR-1GE2LX-SFP User manual

Brand: Aventura

Model: FBR-1GE2LX-SFP

Category: Network media converters

Type: User manual

Download PDF

report

Aventura FBR-1GE2LX-SFP User manual

Aventura FBR-1GE2LX-SFP User manual

Related papers

Other documents