Behringer Tube Ultragain MIC200 Quick start guide

Quick Start Guide (Check Out behringer.com for FullManual)

TUBE ULTRAGAIN MIC200

Audiophile Vacuum Tube Preamplier with

Preamp Modeling Technology

INPUT OUTPUT

2 TUBE ULTRAGAIN MIC200 3Quick Start Guide

Terminals marked with this

symbol carry electrical current

of sucient magnitude to

constitute risk of electric shock. Use only

high-quality professional speaker cables

with ¼" TS or twist-locking plugs

pre-installed. Allother installation or

modication should be performed only by

qualiedpersonnel.

This symbol, wherever it

appears, alerts you to the

presence of uninsulated

dangerous voltage inside the enclosure -

voltage that may be sucient to constitute

a risk ofshock.

This symbol, wherever it

appears, alerts you to

important operating and

maintenance instructions in the

accompanying literature. Please read

themanual.

Caution

To reduce the risk of electric

shock, do not remove the

top cover (or the rear section). No user

serviceable parts inside. Refer servicing to

qualiedpersonnel.

Caution

To reduce the risk of re or

electric shock, do not expose

this appliance to rain and moisture.

Theapparatus shall not be exposed to

dripping or splashing liquids and no objects

lled with liquids, such as vases, shall be

placed on the apparatus.

Caution

These service instructions are

for use by qualied service

personnel only. Toreduce the risk of electric

shock do not perform any servicing other

than that contained in the operation

instructions. Repairshave to be performed

by qualied servicepersonnel.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus

nearwater.

6. Clean only with dry cloth.

7. Do not block any ventilation

openings. Install in accordance with the

manufacturer’s instructions.

8. Do not install near any heat sources

such as radiators, heat registers, stoves,

orother apparatus (including ampliers)

thatproduceheat.

9. Do not defeat the safety purpose

of the polarized or grounding-type plug.

Apolarized plug has two blades with one

wider than the other. A grounding-type

plug has two blades and a third grounding

prong. The wide blade or the third prong

are provided for your safety. Ifthe provided

plug does not t into your outlet, consult

an electrician for replacement of the

obsoleteoutlet.

10. Protect the power cord from being

walked on or pinched particularly at plugs,

convenience receptacles, and the point

where they exit from theapparatus.

11. Use only attachments/accessories

specied by themanufacturer.

12. Use only

with the cart,

stand, tripod,

bracket, ortable

specied by the

manufacturer, orsold

with the apparatus. When a cart is used,

usecaution when moving the cart/

apparatus combination to avoid injury from

tip-over.

13. Unplug this apparatus during

lightning storms or when unused for long

periods oftime.

14. Refer all servicing to qualied service

personnel. Servicing is required when

the apparatus has been damaged in any

way, such as power supply cord or plug

is damaged, liquid has been spilled or

objects have fallen into the apparatus,

the apparatus has been exposed to rain or

moisture, does not operate normally, orhas

beendropped.

15. The apparatus shall be connected to

a MAINS socket outlet with a protective

earthingconnection.

16. Where the MAINS plug or an

appliance coupler is used as the disconnect

device, thedisconnect device shall remain

readilyoperable.

LEGAL DISCLAIMER

TECHNICAL SPECIFICATIONS AND

APPEARANCES ARE SUBJECT TO CHANGE

WITHOUT NOTICE AND ACCURACY IS NOT

Important Safety

Instructions

4 TUBE ULTRAGAIN MIC200 5Quick Start Guide

GUARANTEED. BEHRINGER IS PART OF

THE MUSIC GROUP (MUSIC-GROUP.COM).

ALL TRADEMARKS ARE THE PROPERTY OF

THEIR RESPECTIVE OWNERS. MUSICGROUP

ACCEPTS NO LIABILITY FOR ANY LOSS

WHICH MAY BE SUFFERED BY ANY PERSON

WHO RELIES EITHER WHOLLY OR IN PART

UPON ANY DESCRIPTION, PHOTOGRAPH

OR STATEMENT CONTAINED HEREIN.

COLORSAND SPECIFICATIONS MAY VARY

FROM ACTUAL PRODUCT. MUSICGROUP

PRODUCTS ARE SOLD THROUGH

AUTHORIZED FULLFILLERS AND RESELLERS

ONLY. FULLFILLERS AND RESELLERS ARE

NOT AGENTS OF MUSICGROUP AND HAVE

ABSOLUTELY NO AUTHORITY TO BIND

MUSICGROUP BY ANY EXPRESS OR IMPLIED

UNDERTAKING OR REPRESENTATION.

THISMANUAL IS COPYRIGHTED. NO PART

OF THIS MANUAL MAY BE REPRODUCED OR

TRANSMITTED IN ANY FORM OR BY ANY

MEANS, ELECTRONIC OR MECHANICAL,

INCLUDING PHOTOCOPYING AND

RECORDING OF ANY KIND, FORANY

PURPOSE, WITHOUTTHE EXPRESS WRITTEN

PERMISSION OF MUSICGROUPIPLTD.

Trident Chambers, Wickhams Cay,

P.O. Box 146, Road Town, Tortola,

BritishVirgin Islands

LIMITED WARRANTY

§ 1 Warranty

(1) This limited warranty is valid only

if you purchased the product from a

MUSICGroup Authorized Reseller in the

country of purchase. A list of authorized

resellers can be found on BEHRINGER’s

website behringer. com under “Where to

Buy“, oryou can contact the MUSIC Group

oce closest toyou.

(2) MUSICGroup* warrants the

mechanical and electronic components

of this product to be free of defects in

material and workmanship if used under

normal operating conditions for a period

of one (1) year from the original date of

purchase (seethe Limited Warranty terms

in §4below), unless a longer minimum

warranty period is mandated by applicable

local laws. If the product shows any defects

within the specied warranty period

and that defect is not excluded under

§4, MUSICGroup shall, at its discretion,

eitherreplace or repair the product using

suitable new or reconditioned product

or parts. Incase MUSICGroup decides to

replace the entire product, thislimited

warranty shall apply to the replacement

product for the remaining initial warranty

period, i.e., one(1) year (orotherwise

applicable minimum warranty period)

from the date of purchase of the

originalproduct.

(3) Upon validation of the warranty

claim, the repaired or replacement product

will be returned to the user freight prepaid

by MUSICGroup.

(4) Warranty claims other than those

indicated above are expressly excluded.

PLEASE RETAIN YOUR SALES RECEIPT.

ITISYOUR PROOF OF PURCHASE COVERING

YOUR LIMITED WARRANTY. THIS LIMITED

WARRANTY IS VOID WITHOUT SUCH PROOF

OFPURCHASE.

§ 2 Online registration

Please do remember to register your

new BEHRINGER equipment right after

your purchase at behringer. com under

“Support” and kindly read the terms and

conditions of our limited warranty carefully.

Registeringyour purchase and equipment

with us helps us process your repair claims

quicker and more eciently. Thank you for

yourcooperation!

§ 3 Return materials

authorization

(1) To obtain warranty service,

pleasecontact the retailer from whom the

equipment was purchased. Shouldyour

MUSIC Group Authorized Reseller not be

located in your vicinity, youmay contact

the MUSIC Group Authorized Fulller

for your country listed under “Support”

at behringer. com. Ifyour country is not

listed, please check if your problem can be

dealt with by our “Online Support” which

may also be found under “Support” at

behringer. com. Alternatively,please submit

an online warranty claim at behringer. com

BEFORE returning the product. All inquiries

must be accompanied by a description

of the problem and the serial number of

the product. Afterverifying the product’s

warranty eligibility with the original

sales receipt, MUSICGroup will then

issue a ReturnMaterials Authorization

(“RMA”)number.

(2) Subsequently, the product must be

returned in its original shipping carton,

together with the return authorization

number to the address indicated by

MUSICGroup.

(3) Shipments without freight prepaid

will not beaccepted.

§ 4 Warranty Exclusions

(1) This limited warranty does not

cover consumable parts including,

butnot limited to, fuses and batteries.

Whereapplicable, MUSICGroup warrants

the valves or meters contained in the

product to be free from defects in material

6 TUBE ULTRAGAIN MIC200 7Quick Start Guide

and workmanship for a period of ninety

(90) days from date ofpurchase.

(2) This limited warranty does not cover

the product if it has been electronically

or mechanically modied in any way.

If the product needs to be modied or

adapted in order to comply with applicable

technical or safety standards on a national

or local level, inany country which is not

the country for which the product was

originally developed and manufactured,

thismodication/adaptation shall not

be considered a defect in materials or

workmanship. Thislimited warranty

does not cover any such modication/

adaptation, regardlessof whether

it was carried out properly or not.

Underthe terms of this limited warranty,

MUSICGroup shall not be held responsible

for any cost resulting from such a

modication/ adaptation.

(3) This limited warranty covers only

the product hardware. It does not cover

technical assistance for hardware or

software usage and it does not cover

any software products whether or not

contained in the product. Any such

software is provided “AS IS” unless expressly

provided for in any enclosed software

limitedwarranty.

(4) This limited warranty is invalid if the

factory-applied serial number has been

altered or removed from theproduct.

(5) Free inspections and maintenance/

repair work are expressly excluded from this

limited warranty, in particular, ifcaused by

improper handling of the product by the

user. This also applies to defects caused

by normal wear and tear, in particular,

offaders, crossfaders, potentiometers,

keys/ buttons, guitarstrings, illuminants

and similarparts.

(6) Damage/defects caused by the

following conditions are not covered by this

limitedwarranty:

• improper handling, neglect or failure

to operate the unit in compliance

with the instructions given in

BEHRINGER user or servicemanuals;

• connection or operation of the unit in

any way that does not comply with

the technical or safety regulations

applicable in the country where the

product is used;

• damage/defects caused by acts of

God/Nature (accident, re, ood, etc)

or any other condition that is beyond

the control of MUSICGroup.

(7) Any repair or opening of the

unit carried out by unauthorized

personnel (userincluded) will void the

limitedwarranty.

(8) If an inspection of the product by

MUSICGroup shows that the defect in

question is not covered by the limited

warranty, theinspection costs are payable

by thecustomer.

(9) Products which do not meet the

terms of this limited warranty will be

repaired exclusively at the buyer’s expense.

MUSICGroup or its authorized service

center will inform the buyer of any such

circumstance. If the buyer fails to submit a

written repair order within 6 weeks after

notication, MUSICGroup will return the

unit C.O.D. with a separate invoice for

freight and packing. Such costs will also

be invoiced separately when the buyer has

sent in a written repair order.

(10) MUSIC Group Authorized Resellers

do not sell new products directly in online

auctions. Purchases made through an

online auction are on a “buyer beware”

basis. Onlineauction conrmations or sales

receipts are not accepted for warranty

verication and MUSICGroup will not repair

or replace any product purchased through

an onlineauction.

§ 5 Warranty transferability

This limited warranty is extended

exclusively to the original buyer

(customerof authorized reseller) andis

not transferable to anyone who may

subsequently purchase this product.

Noother person (reseller,etc.) shallbe

entitled to give any warranty promise on

behalf of MUSICGroup.

§ 6 Claim for damage

Subject only to the operation of mandatory

applicable local laws, MUSICGroup shall

have no liability to the buyer under this

warranty for any consequential or indirect

loss or damage of any kind. In no event

shall the liability of MUSICGroup under this

limited warranty exceed the invoiced value

of theproduct.

§ 7 Limitation of liability

This limited warranty is the complete

and exclusive warranty between you

and MUSICGroup. It supersedes all other

written or oral communications related

to this product. MUSICGroup provides no

other warranties for this product.

§ 8 Other warranty rights

and nationallaw

(1) This limited warranty does not

exclude or limit the buyer’s statutory rights

as a consumer in any way.

(2) The limited warranty regulations

mentioned herein are applicable unless

they constitute an infringement of

applicable mandatory local laws.

Page is loading ...

TUBE ULTRAGAIN MIC20038 39 Quick Start Guide

TUBE ULTRAGAIN MIC200 Controls

INPUT OUTPUT

(1) (2)(4) (5) (6) (7)(3) (8) (9)

User interface of the MIC200

(12)

(11)

(10)

The rear panel of your MIC200

TUBE ULTRAGAIN MIC20040 41 Quick Start Guide

TUBE ULTRAGAIN MIC200 Controls

(1) The GAIN control allows you to

control the gain from +26 to +60 dB

to the input signal. This control should

be set all the way to the left when

(dis)connecting a sound source from

the MIC200. When all connections

are made, slowly start raising the

gaincontrol.

(2) We recommend using the LED

meter to adjust gain. The LED chain

displays the output signal level in dB.

Pleasemake sure that the clip LED

never lights up permanently. It should

light up only at peak signals, but it

should never be on all the time.

(3) If your MIC200 is connected to the

mains via the enclosed power supply

unit, the POWER LED lights up to

indicate that your MIC200 is running.

(4) The 20 dB PAD switch reduces

the input sensitivity by 20 dB

(switchpressed). The appropriate

setting depends on the equipment

connected. Generally speaking,

lowering the signal level in mic

applications is not recommended.

No matter what your application is,

the clip LED warns you to reduce the

gain setting to avoiddistortion.

(5) This +48 V switch activates the

phantom power supply for the XLR

input. Phantom power supply is

required for operating condenser

microphones. Dynamic microphones

require no phantom power.

(6) Press the LOW CUT switch to

eliminate undesired subsonic noise,

such as oorrumble.

(7) With the PHASE REVERSE switch,

the input signal is reversed by 180°.

This function is available for both mic

and line signals. Use this function

in a multi-microphone setup if you

detect phase cancellations in specic

frequency bands.

(8) The OUTPUT control governs the

output level within a range from

-∞to+10dB. If the control is

turned all the way to the left, there

is no output signal at all. The more

the control is turned to the right,

the higher the output level.

(9) The PREAMP MODE rotary switch

gives you a wide selection of

preamppresets. The options available

are: WARM, WARM/LIMITER,

LIMITERandNEUTRAL.

(EN) Controls

(10) The balanced ¼" TRS INPUT of

your MIC200 can be used to connect

your electric guitar, for example.

This input is wired parallell to the

XLR input.

Ideally, the balanced XLR INPUT should

be used to connect a microphone.

◊ In contrast to its outputs,

the MIC200’s inputs should never

be used simultaneously!

(11) This is the balanced XLR OUTPUT of

your MIC200. Use this connector to

feed the XLR input of your mixing

console, multitrack recorder or

poweramp.

The balanced ¼" TRS OUTPUT of

your MIC200 can also be connected

to a mixer, recording system or

poweramp.

(12) Use the POWER SUPPLY

CONNECTOR to hook up the enclosed

power supply unit. Next to this

connector you’ll nd the strain relief

clamp, which prevents accidental

release of the power supply.

Check Out behringer.com for Full Manual

Page is loading ...

50 TUBE ULTRAGAIN MIC200 51Quick Start Guide

Specications

Audio Inputs

XLR Input

Connector balanced/unbalanced

Type transformerless, DC-decoupledinput

Impedance approx. 2kΩ

Max. input level +7dBu / -20 dB with pad

¼" TRS Input

Connector balanced/unbalanced

Type transformerless, DC-decoupledinput

Impedance approx. 1MΩ

Max. input level

+16dBu / -20 dB with pad

E.I.N.

1

(20 Hz - 20 kHz)

@ 0Ω source resistance

-125.5dBu / -128.5dBu A-weighted

@ 150Ω source resistance

-124dBu / -126.8dBu A-weighted

@ 600Ω source resistance

-120dBu / -122.7dBu A-weighted

Audio Outputs

Connectors

XLR connector + ¼" TRS jack

balanced/unbalanced

Type transformerless, DC-decoupledoutput

Impedance approx. 700Ω balanced / 350Ω unbalanced

Max. output level approx. +26dBu @ 100kΩ

System Data

Signal-to-noise ratio 90dB A-weighted @ -28dBu inputlevel

Frequency Response

Mic input <10Hz to 47kHz (±3dB)

Line input <10Hz to 55kHz (±3dB)

Function Controls

GAIN variable ( +26dB to +60dB)

OUTPUT variable ( -∞ to +10dB)

Preamp mode control

selection of various preamp settings for

microphone andinstruments

Function Switches

20 dB PAD level attenuation (20dB)

+48 V activates the phantom power

LOW CUT High pass lter (cut-ofrequency90Hz)

PHASE REVERSE Phase reverse (180°)

Indicators

Input Level

8-segment LED meter:

-24, -18, -12, -6, 0, +6, +12, Clip

Power LED indicates operation

Power Supply

Mains Voltage

USA/Canada 120V~, 60Hz

Europe/U.K./Australia 230V~, 50Hz

China 220V~, 50Hz

Korea 220V~, 60Hz

Japan 100V~, 50 / 60Hz

Mains connector external power supply 9V~ / 1300mA

Dimensions

Dimensions (H x W x D)

approx. 2.5 x 5.3 x 5.3"

approx.64x 135x 135mm

Weight (without power supply) approx. 2.2 lbs / 1.0kg

1

Equivalent Input Noise

BEHRINGER is constantly striving to maintain the highest professional standards. As a result of these efforts,

modifications may be made from time to time to existing products without prior notice. Specifications and

appearance may differ from those listed or illustrated.

Page is loading ...

60 61Quick Start GuideTUBE ULTRAGAIN MIC200

1. Register online. Please register your

new MUSIC Group equipment right after you

purchase it by visiting behringer. com. Registering

your purchase using our simple online form helps

us to process your repair claims more quickly and

eciently. Also, read the terms and conditions of

our warranty, ifapplicable.

2. Malfunction. Should your

MUSICGroup Authorized Reseller not be located

in your vicinity, you may contact the MUSIC Group

Authorized Fulller for your country listed under

“Support” at behringer. com. Shouldyour country

not be listed, please check if your problem can be

dealt with by our “OnlineSupport” which may

also be found under “Support” at behringer. com.

Alternatively, please submit an online warranty

claim at behringer. com BEFORE returning

theproduct.

3. Power Connections. Before

plugging the unit into a power socket, please

make sure you are using the correct mains

voltage for your particular model. Faultyfuses

must be replaced with fuses of the same typeand

rating without exception.

1. Registro online. Le recomendamos

que registre su nuevo aparato MUSIC Group justo

después de su compra accediendo a la página

web behringer. com. Elregistro de su compra

a través de nuestro sencillo sistema online

nos ayudará a resolver cualquier incidencia

que se presente a la mayor brevedad posible.

Además,aproveche para leer los términos y

condiciones de nuestra garantía, si es aplicable

en sucaso.

2. Averías. En el caso de que no exista un

distribuidor MUSIC Group en las inmediaciones,

puede ponerse en contacto con el distribuidor

MUSIC Group de su país, queencontrará dentro

del apartado “Support” de nuestra página web

behringer. com. En caso de que su país no aparezca

en ese listado, acceda a la sección “Online Support”

(quetambiénencontrará dentro del apartado

“Support” de nuestra páginaweb) y compruebe si

su problema aparece descrito y solucionado allí. De

forma alternativa, envíenos a través de la página

web una solicitud online de soporte en periodo de

garantía ANTES de devolvernos el aparato.

3. Conexiones de corriente. Antes

de enchufar este aparato a una salida de corriente,

asegúrese de que dicha salida sea del voltaje

adecuado para su modelo concreto. En caso de que

deba sustituir un fusible quemado, deberá hacerlo

por otro de idénticas especicaciones, sinexcepción.

Important information

Aspectos importantes

Other important information

1. Enregistrez-vous en ligne.

Prenez le temps d’enregistrer votre produit

MUSIC Group aussi vite que possible sur le site

Internet behringer. com. Le fait d’enregistrer

le produit en ligne nous permet de gérer les

réparations plus rapidement et plus ecacement.

Prenezégalement le temps de lire les termes et

conditions de notre garantie.

2. Dysfonctionnement. Si vous

n’avez pas de revendeur MUSIC Group près de

chez vous, contactez le distributeur MUSIC Group

de votre pays: consultez la liste des distributeurs

de votre pays dans la page “Support” de notre

site Internet behringer. com. Si votre pays n’est

pas dans la liste, essayez de résoudre votre

problème avec notre “aideen ligne” que vous

trouverez également dans la section “Support”

du site behringer. com. Vous pouvez également

nous faire parvenir directement votre demande

de réparation sous garantie par Internet sur le

site behringer. com AVANT de nous renvoyer le

produit.

3. Raccordement au secteur.

Avant de relier cet équipement au secteur,

assurez-vous que la tension secteur de votre

région soit compatible avec l’appareil. Veillez

à remplacer les fusibles uniquement par des

modèles exactement de même taille et de même

valeur électrique — sans aucune exception.

1. Online registrieren. Bitte

registrieren Sie Ihr neues MUSIC Group-

Gerät direkt nach dem Kauf auf der

Website behringer. com. Wenn Sie Ihren Kauf mit

unserem einfachen online Formular registrieren,

können wir Ihre Reparaturansprüche schneller

und ezienter bearbeiten. Lesen Sie bitte auch

unsere Garantiebedingungen, fallszutreend.

2. Funktionsfehler. Sollte sich

kein MUSICGroup Händler in Ihrer Nähe

benden, können Sie den MUSICGroup

Vertrieb Ihres Landes kontaktieren, derauf

behringer. com unter „Support“ aufgeführt

ist. Sollte Ihr Land nicht aufgelistet sein,

prüfen Sie bitte, ob Ihr Problem von unserem

„Online Support“ gelöst werden kann, den Sie

ebenfalls auf behringer. com unter „Support“

nden. Alternativ reichen Sie bitte Ihren

Garantieanspruch online auf behringer. com ein,

BEVOR Sie das Produktzurücksenden.

3. Stromanschluss. Bevor Sie das

Gerät an eine Netzsteckdose anschließen, prüfen

Sie bitte, obSie die korrekte Netzspannung für

Ihr spezielles Modell verwenden. Fehlerhafte

Sicherungen müssen ausnahmslos durch

Sicherungen des gleichen Typs und Nennwerts

ersetztwerden.

Informations

importantes

Wegitere wichtige

Informationen

Page is loading ...

We Hear You

Behringer Tube Ultragain MIC200 Quick start guide

Related papers

Other documents