Add-On Computer Peripherals (ACP) 10GB-LR-SFPP-AO Datasheet
- Category
- Network transceiver modules
- Type
- Datasheet
Add-On Computer Peripherals (ACP) 10GB-LR-SFPP-AO is a 10Gb/s serial optical interface compliant to 802.3ae 10GBASE LR standards. It is designed to transmit and receive optical data over single mode optical fiber for link lengths up to 10km. The device features a 1310nm DFB transmitter and a PIN photo-detector, and is compliant with SFF-8431 and SFF 8472 specifications. It has a 2-wire interface for management, supports digital diagnostic monitoring and has low power consumption.
Add-On Computer Peripherals (ACP) 10GB-LR-SFPP-AO is a 10Gb/s serial optical interface compliant to 802.3ae 10GBASE LR standards. It is designed to transmit and receive optical data over single mode optical fiber for link lengths up to 10km. The device features a 1310nm DFB transmitter and a PIN photo-detector, and is compliant with SFF-8431 and SFF 8472 specifications. It has a 2-wire interface for management, supports digital diagnostic monitoring and has low power consumption.
AddOn Computer Phone: 877.292.1701
Page 1 of 10
10GB-LR-SFPP-AO
ENTERASYS, 10GBASE-LR SFP+ SMF
1310NM 10KM REACH LC
10GB-LR-SFPP-AO
10Gbase SFP+ Transceiver
Features
• 10Gb/s serial optical interface compliant to 802.3ae
10GBASE LR
• Electrical interface compliant to SFF-8431
specifications for enhanced 8.5 and 10 Gigabit
small from factor pluggable module “SFP+”
• 1310NM DFB transmitter, PIN photo-detector
• 2-wire interface for management specifications
compliant with SFF 8472 digital diagnostic monitoring
interface for optical transceivers
• Operating case temperature: 0°C to +70°C
• All-metal housing for superior EMI performance
• Low power consumption
• Advanced firmware allow customer system encryption
Information to be stored in transceiver
• Cost effective SFP+ solution, enables higher port
densities and greater bandwidth
Applications
High-speed storage area network
Computer cluster cross-connect
Customer high_speed data pipes
10GE Storage, 8G Fiber Channel
Product Description
This 1310 nm DFB 10Gigabit SFP+ transceiver is designed to transmit and receive
optical data over single mode optical fiber for link length 10km.
The 10GB-LR-SFPP-AO module electrical interface is compliant to SFI electrical
specifications The transmitter input and receiver output impedance is 100 Ohms
differential. Data lines are internally AC coupled. The module differential termination and
reduce differential to common mode conversion for quality signal termination and low
EMI. SFI typically operates over 200mm of improved FR4 material or up to about
150mm of standard FR4 with connector.
The transmitter converts 10Gbit/s serial PECL or CML electrical data into serial optical
data compliant with the 10GBASE-LR standard. An open collector compatible Transmit
Disable (Tx_Dis) is provided. A logic “1,” or connection on this pin will disable the laser
from transmitting. A logic “0” on this pin provides normal opteration. The transmitter has
a internal automatic power control loop (APC) to ensure constant optical power output
across supply voltage and temperature variations. An open collector compatible
AddOn Computer Phone: 877.292.1701
Page 2 of 10
10GB-LR-SFPP-AO
ENTERASYS, 10GBASE-LR SFP+ SMF
1310NM 10KM REACH LC
Transmit Fault (TFault) is provided. TX_Fault is a module output contact that when high,
indicates that the module transmitter has detected a fault condition related to laser
operation or safety. The TX_Fault output contact is an open drain.collector and shall be
pulled up to Vcc-Host in the host with a resistor in the range 4 7-10kΩ. TX_Disable is a
module input contact. When TX_Disable is asserted high or left open, the SFP+ module
transmitter output shall be turned off. This contact shall be pulled up to VccT with a
4.7kΩ to 10kΩ resistor.
The Receiver converts 10Gbit/s serial optical data into serial PECL/CML electrical data.
An open compatible Loss of Signal is provided. Tx_LOS when high indicates an optical
signal level below that specified in the relevant standard. The Rx-LOS contact is an open
drain.collector output and shall be pulled up to Vcc_Host in the host with a resistor in the
range 4.7-10kΩ, or with an active termination. Power supply filtering is recommended for
both the transmitter and receiver. The Rx_LOS signal is intended as a preliminary
indication to the system in which the SFP+ is installed that the received signal strength is
below the specified range. Such an indication typically points to non-installed cables,
broken cables, or a disabled, failing or a powered off transmitter at the far end of the
cable.
Pin Definition
The SFP+ modules are hot-pluggable. Hot pluggable refers to plugging or unplugging a
module while the host board is powered. The SFP+ host connector is a 0.8mm pitch 20
position right angle improved connector specified by SFF-8083 or stacked connector
with equivalent electrical performance. Host PCB contacts mates with the host in the
order of ground, power, followed by signal as illustrated by Figure 3 and the contact
sequence order listed in Table 2.
AddOn Computer Phone: 877.292.1701
Page 3 of 10
10GB-LR-SFPP-AO
ENTERASYS, 10GBASE-LR SFP+ SMF
1310NM 10KM REACH LC
Figure 2: Module Interface to Host
Figure 3: Module Contact Assignment
AddOn Computer Phone: 877.292.1701
Page 4 of 10
10GB-LR-SFPP-AO
ENTERASYS, 10GBASE-LR SFP+ SMF
1310NM 10KM REACH LC
Note:
1. Module ground pins GND are isolated from the module case.
2. Shall be pulled up with 4.7K-10Kohms to a voltage between 3.15V and 3.45V on
the host bard.
PIN
Logic
Symbol
Name/Description
Unit
1
VEET
Module transmitter Ground
1
2
LVTTL-O
TX_Fault
Module Transmitter Fault
3
LVTTL-I
TX_Dis
Transmitter Disable; Turns off
transmitter laser output
4
LVTTL-I/O
SDA
2-Wire Serial Interface Data Line
2
5
LVTTL-I
SCL
2-Wire Serial Interface Clock
2
6
MOD_DEF0
Module Definition, Grounded in
the module
7
LVTTL-I
RS0
Receiver Rate Select
8
LVTTL-O
RX_LOS
Receiver Loss of Signal
Indication Active LOW
9
LVTTL-I
RS1
Transmitter Rate Select (not
used)
10
VeeR
Module Receiver Ground
1
11
VeeR
Module Receiver Ground
1
12
CML-O
RD-
Receiver inverted Data Output
13
CML-O
RD+
Receiver Data Output (not used)
14
VeeR
Module Receiver Ground
1
15
VccR
Module Receiver 3.3 V Supply
16
VccT
Module Receiver 3.3 V Supply
17
VccT
Module Transmitter Ground
1
18
CML-I
TD+
Receiver Non-Inverted Data
output
19
CML-I
TD-
Transmitter Inverted Data Input
20
VeeT
Module Transmitter Ground
1
AddOn Computer Phone: 877.292.1701
Page 5 of 10
10GB-LR-SFPP-AO
ENTERASYS, 10GBASE-LR SFP+ SMF
1310NM 10KM REACH LC
Table 1: SFP+ Module PIN Definition
4. TRANSCEIVER BLOCK DIAGRAM
5. ABSOLUTE MAXIMUM RATING
These values represent the damage threshold of the module. Stress in excess of any of
the individual Absolute Maximum Ratings can cause immediate catastrophic damage to
the module even if all other parameters are within Recommended Operating
Table 2: Absolute Maximum Rating
6. RECOMMENDED OPERATING ENVIRONMENT
Recommended Operating Environment specifies parameters for which the
electrical and optical characteristics hold unless otherwise noted.
Parameters
Symbol
Min.
Max.
Unit
Power Supply Voltage
Vcc
0
3.6
V
Storage Temperature
Tc
-40
85
°C
Operating Case
Temperature
Tc
0
70
°C
Relative Humidity
RH
5
95
%
RX Input Average Power
Pmax
-
0
dBm
Parameters
Symbol
Min.
Typical
Max.
Unit
Power Supply Voltage
Vcc
3.135
3.3
3.465
V
Operating Case
Temperature
Tc
0
25
70
°C
AddOn Computer Phone: 877.292.1701
Page 6 of 10
10GB-LR-SFPP-AO
ENTERASYS, 10GBASE-LR SFP+ SMF
1310NM 10KM REACH LC
Table 3: Recommended Operating Environment
7. OPTICAL CHARACTERISTICS
The following characteristics are defined over the Recommended Operating
Environment unless otherwise specified.
Parameter
Values
Unit
Operating Reach
2-10K
m
Transmitter
Center wavelength (range)
1260-1355
nm
Side Mode Suppression Ratio (min)
30
dB
Launched power
- maximum (average)
0.5
dBm
- maximum (average)
-8.2
dBm
- OMA
0.2
dBm
- OMA-TDP (min)
-6.2
dBm
Transmitter and dispersion penalty (max)
3.2
dB
Average launch power of OFF transmitter (max)
-30
dBm
Extinction ratio (min)
3.5
dB
RIN12 OMA (max)
-128
dB/Hz
Optical Return Loss Tolerance (min)
12
dB
Receiver
Center wavelength (range)
1260-1355
nm
Receive overload (max) in average power (note 1)
0.5
dBm
Receive sensitivity (min) in average power (note 1)
-14.4
dBm
Receiver sensitivity (max) in OMA (note2)
-12.6
dBm
Receiver Reflectance (max)
-12
dB
Stressed receiver sensitivity (max) in OMA (note2)
-10.3
dBm
Vertical eye elosure penalty (min)(note3)
2.2
dB
Los Assert (min)
-30
dBm
Los Dessert (max)
-12
dBm
Los Hysteresis (min)
0.5
dB
Stressed eye jitter (min)(note2)
0.3
Ulp-p
Receive electrical 3dB upper cut off frequency (max)
12.3
GHz
AddOn Computer Phone: 877.292.1701
Page 7 of 10
10GB-LR-SFPP-AO
ENTERASYS, 10GBASE-LR SFP+ SMF
1310NM 10KM REACH LC
Receiver power (damage, Max)
1.5
dBm
Note:
1. Average optical power shall be measured using the methods spevified in
TIA/EIA-455-95.
2. Receiver sensitivity is informative. Stressed receiver sensitivity shall be
measured with conformance test signal for BER =1x 10
-12
3. Vertical eye closure penalty and stressed eye jitter are the test conditions for
measuring stressed receiver sensitivity. They are not the required characteristic
of the receiver.
4. Power budget is defined as the different between the Rx sensitivity and the Tx.
Output power of the interface.
5. Path penalty is intended as the power penalty of the interface between back-to-
back and the maximum applied dispersion.
8. DIGITAL DIAGNOSTIC FUNCTIONS
The following digital diagnostic characteristics are defined over the
Recommended Operating Environment unless otherwise specified. It is compliant
to SFF8472 Rev10.2 with internal calibration mode. For external clibration please
contact our sales staff.
Table 5: Digital diagnostic specification table
Parameters
Symbol
Min.
Max.
Unit
Notes
Temperature monitor
absolute error
DMI_Temp
-3
3
degC
Over operating temp
Laser power monitor
absolute error
DMI_TX
-3
3
dB
RX power monitor
absolute error
DMI_RX
-3
3
dB
-1dBm to -15dBm
range
Supply voltage
monitor absolute error
DMI_VCC
-0.08
0.08
V
Full operating range
Bias current monitor
DMI_Ibias
-10%
10%
mA
AddOn Computer Phone: 877.292.1701
Page 8 of 10
10GB-LR-SFPP-AO
ENTERASYS, 10GBASE-LR SFP+ SMF
1310NM 10KM REACH LC
9. ELETRICAL CHARACTERISTICS
The following electrical characteristics are defined over the Recommended Operating
Environment unless otherwise specified.
PIN
Symbol
Min.
Typical
Max.
Unit
Notes
Data Rate
-
10.3125
-
Gbps
Power Consumption
-
800
1000
mW
Transmitter
Single Ended Output Voltage
Tolerance
-0.3
-
4
V
C common mode voltage
tolerance
15
-
-
mV
Tx Input Diff Voltage
VI
90
350
mV
Tx Fault
VoI
-0.3
0.4
V
At 0.7 nA
Data Dependent Input Jitter
DDJ
0.1
UI
Data Input Total Jitter
TJ
0.28
UI
Receiver
Single Ended Output Voltage
Tolerance
-0.3
-
4
V
Rx Output Diff Voltage
Vo
150
425
mV
Rx Output Rise and Fall Time
Tr/Tf
30
ps
20% to
80%
Total Jitter
TJ
0.7
UI
Deterministic Jitter
DJ
0.7
UI
AddOn Computer Phone: 877.292.1701
Page 9 of 10
10GB-LR-SFPP-AO
ENTERASYS, 10GBASE-LR SFP+ SMF
1310NM 10KM REACH LC
11. MECHANICAL
Complies with SFF-8432 rev. 5.0
AddOn Computer Phone: 877.292.1701
Page 10 of 10
10GB-LR-SFPP-AO
ENTERASYS, 10GBASE-LR SFP+ SMF
1310NM 10KM REACH LC
Contact Information
AddOn Computer, Inc. is a leading supplier of Memory Upgrade, Network Transceivers
and Network connectivity products to Channel Partners, Resellers and OEMs, with more
than seventeen years of direct industry experience. AddOn Computer (ACP) has been
the exclusive supplier to Ingram Micro's "Memory Upgrades" program for the past nine
years.
AddOn Computer maximizes profitable opportunities for our partners. Our ability to
source product worldwide, ensures that our pricing will always be competitive. Offering
turnkey solutions, AddOn Computer has forged a reputation as a solutions provider,
delivering high quality, cost effective product in a timely and reliable manner.
Corporate offices:
AddOn Computer
34A Mauchly
Irvine, CA 92618
Tel: 877-292-1701
Fax: 949-861-2812
Email: sales@addoncomputer.com
Email: support@addoncomputer.com
Web: http://www.addoncomputer.com
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
Add-On Computer Peripherals (ACP) 10GB-LR-SFPP-AO Datasheet
- Category
- Network transceiver modules
- Type
- Datasheet
Add-On Computer Peripherals (ACP) 10GB-LR-SFPP-AO is a 10Gb/s serial optical interface compliant to 802.3ae 10GBASE LR standards. It is designed to transmit and receive optical data over single mode optical fiber for link lengths up to 10km. The device features a 1310nm DFB transmitter and a PIN photo-detector, and is compliant with SFF-8431 and SFF 8472 specifications. It has a 2-wire interface for management, supports digital diagnostic monitoring and has low power consumption.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Add-On Computer Peripherals (ACP) 10G-SFPP-LR-AO Datasheet
-
-
-
-
-
-
-
