Albatron PX915GC PRO User manual

PX915PC/ PX915GC Series

Copyright

All rights are reserved. No part of this publication may be reproduced, transmitted, transcribed,

stored in a retrieval system or translated into any language or computer language, in any form or by

any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the

prior written permission of the company. Brands and product names are trademarks or registered

trademarks of their respective companies.

The vendor makes no representations or warranties with respect to the contents herein and especially

disclaim any implied warranties of merchantability or fitness for any purpose. Further the vendor

reserves the right to revise this publication and to make changes to the contents herein without

obligation to notify any party beforehand. Duplication of this publication, in part or in whole, is not

allowed without first obtaining the vendor’s approval in writing.

Trademark

All the trademarks or brands in this document are registered by their respective owner.

Disclaimer

We make no warranty of any kind with regard to the content of this user’s manual. The content is

subject to change without notice and we will not be responsible for any mistakes found in this user’s

manual. All the brand and product names are trademarks of their respective companies.

FCC Compliance Statement

This equipment has been tested and found to comply with the limits of a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. Operation of this equipment in a residential area

is likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense. However, there is no guarantee that interference will not occur in a

particular installation.

CE Mark

The device is in accordance with 89/336 ECC-ENC Directive.

Important, please read!!!

120410127M1N

Ver: TC101

0 The images and pictures in this manual are for reference only and may vary

slightly from actual product installation depending on specific hardware

models, third party components and software versions.

0 Unplug your computer when installing components and configuring switches

and pins.

0 This mainboard contains very delicate IC chips. Use a grounded wrist strap

when working with the system.

0 Do not touch the IC chips, leads, connectors or other components.

0 Unplug the AC power when you install or remove any device on the

mainboard.

Package Contents

 PX915PC/ PX915GC Series mainboard

 IDE ATA Cable

 FDC Cable

 USB Bracket (optional)

 Game Port Bracket (optional)

 SPDIF & FRONT AUDIO Port Bracket (optional)

 SATA Power cord (optional)

 SATA Cable (optional)

 Mainboard Setup Driver CD

 Mainboard User Manual CD

 Mainboard Quick Installation Guide

Symbols

Attention …

Following the procedures …

Troubleshooting …

Please refer to …

PX915PC/ PX915GC Series

Intel

®

915P/ 915G & ICH6

Supports Socket 775 Intel

®

Pentium

®

4

Prescott Processor

User Manual

Enabling Hyper-Threading for your computer system requires ALL of the

following components

z CPU: An Intel

®

Pentium

®

4 Processor with HT Technology

z Chipset: An Intel

®

Chipset that supports HT Technology

z BIOS: A BIOS that supports HT Technology must be enabled

z OS: An operating system that supports HT Technology

For more information on Hyper-Threading Technology, go to:

http://www.intel.com/info/hyperthreading

Dimensions (ATX form-factor):

¾ 244mm x 305mm ( W x L )

Operating System:

¾ Supports most popular operating systems: Windows® 2000/ XP

Contents

CHAPTER 1. GETTING STARTED ....................................................1

INTRODUCTION..........................................................................................................1

SPECIFICATION..........................................................................................................2

CONFIGURATION .......................................................................................................5

Layout of PX915PC PRO-G.................................................................................5

Layout of PX915PC PRO.....................................................................................6

Layout of PX915PC..............................................................................................7

Layout of PX915GC PRO-G................................................................................8

Layout of PX915GC PRO....................................................................................9

Layout of PX915GC...........................................................................................10

HARDWARE INSTALLATION ....................................................................................11

CPU Processor Installation.................................................................................11

Back Panel Configuration...................................................................................13

Connectors..........................................................................................................15

Front Panel Indicator: SW/LED、PWRLED、SPEAKER...............................16

Headers & Jumpers.............................................................................................18

Audio Connectors...............................................................................................19

Slots....................................................................................................................21

Power Supply Attachments.................................................................................22

CHAPTER 2. BIOS SETUP........................................................... 23

INTRODUCTION........................................................................................................23

MAIN MENU............................................................................................................24

ADVANCED BIOS FEATURES..................................................................................26

INTEGRATED PERIPHERALS.....................................................................................33

POWER MANAGEMENT............................................................................................38

HARDWARE MONITOR ............................................................................................41

LOAD DEFAULTS.....................................................................................................42

EXIT MENU..............................................................................................................43

CHAPTER 3: SOFTWARE SETUP................................................... 44

SOFTWARE INSTALLATION......................................................................................44

CHAPTER 4: TROUBLESHOOTING................................................. 47

APPENDIX I: 2/ 4/ 6 /8 CHANNEL SETUP..................................................................50

APPENDIX II: INTEL® DESKTOP PROCESSORS FEATURE SET REFERENCE TABLE .51

PX915PC/ PX915GC Series

Chapter 1. Getting Started

Introduction

Congratulations on choosing from the PX915PC/PX915GC series of mainboards! The PX915PC series

includes the PX915PC PRO-G, PX915PC PRO and the PX915PC. The PX915GC series includes the

PX915GC PRO-G, PX915GC PRO and the PX915GC. These mainboards are based on the Intel

®

915P/915G

Northbridge chipsets and the Intel

®

ICH6 Southbridge chipset. They also support Intel

®

Pentium

®

4

Prescott Processors with FSB (Front Side Bus) 533/800 MHz.

These mainboards provide 4 DIMM sockets using 184-pin DDR SDRAM with a total capacity of up to 4 GB

in dual-channel mode. You must install unbuffered, non-ECC DDR400/333 (PC3200/2700) DDR SDRAM

(for more details, see Memory Installation section).

These mainboards provide one 16-lane (x16) PCI-Express slot for use with a PCI-Express graphics card.

This slot can provide 4 GB/s bandwidths in each direction. It also has two 1-lane (x1) PCI-Express slots

for additional cards. These slots provide 250 MB/s bandwidths in each direction.

These mainboards provide a built-in IDE facility (Ultra ATA 66/100) that supports DMA and PIO modes.

These mainboards also have 4 built-in Serial ATA slots capable of 150 MB/s transfer rates on each

channel.

These mainboards also come with an HD Audio sound codec (Azalia standard compliant) which supports

high quality HD Audio with 8 channel capabilities. Sony/Philips Digital Interfaces are also supported.

These mainboards support up to 8 USB2.0 ports and also provide an infrared header for wireless

infrared transmissions.

The PX915PC PRO-G and the PX915GC PRO-G mainboards come with a LAN chip (Marvell

®

MV8001) that

provides up to 1 GB/s network connectivity. And the PX915PC PRO and PX915GC PRO come with

another LAN chip (VIA VT6105 LAN controller) which provides an additional back panel LAN port

capable of 10/100 Mbit/s transmission speeds.

The company’s 3 Year Limited Warranty for this product covers both labor costs and replacement parts

during the 1st year. Only labor costs are covered during the 2nd and 3rd years (replacement parts will

be charged during the 2nd and 3rd years).

All of the information in this manual is for reference only. This specification is subject to change

without notice.

1

PX915PC/ PX915GC Series

Specification

CPU:

¾ Supports Socket 775 Pentium

®

4 Prescott processor

¾ Supports Hyper-Threading Technology

¾ FSB (Front Side Bus)533/ 800 MHz

Chipset:

¾ Northbridge Chipset – Intel® 915P (PX915PC Series)/ 915G (PX915GC Series)

¾ Southbridge Chipset – Intel® ICH6

¾ I/O Controller – Winbond W83627THF

¾ HD Aduio Codec – Realtek ALC880

¾ Gb LAN Controller – Marvell® MV8001 (for PX915PC PRO-G/ PX915GC PRO-G)

¾ Mb LAN Controller – VIA® VT6105 (for PX915PC PRO / PX915GC PRO)

DRAM Memory:

¾ Uses either DDR400 (PC3200) or DDR333 (PC2700) SDRAM

¾ SDRAM modules must be unbuffered and non-ECC

¾ Supported memory module increments are 256 MB /512 MB /1 GB

¾ Total memory capacity is 4 GB (see Memory Installation section for more details)

¾ Supports Dual-Channel data bus

PCI-Express BUS Slots:

¾ Provides 1 x 16 PCI Express slot with 4 GB/s bandwidth (each direction)

¾ Provides 2 x 1 PCI Express slots with 250 MB/s bandwidth (each direction)

¾ All PCI Express slots are fully PCI Express 1.0a compliant

PCI BUS Slots:

¾ Provides 3 PCI slots

¾ Contains 33MHz, 32bit PCI interface, PCI 2.3 is compliant

Universal Serial Bus:

¾ Supports up to 8 USB ports for USB compliant interface devices

¾ Supports USB 2.0 Enhanced Host Controller Interface (EHCI) and USB 1.1 Universal Host

Controller Interface (UHCI)

2

PX915PC/ PX915GC Series

Onboard IDE Facilities:

¾ Supports Ultra ATA 66/ 100, DMA and PIO modes

¾ Supports IDE interface with CD-ROM

¾ Supports high capacity hard disk drives

¾ IDE slot can support 2 IDE drives

Onboard SATA Bus:

¾ 4 SATA IDE slots

¾ SATA 1.0 compatible

¾ Supports 150 MB/s transfer rates

Hardware Monitor Function:

¾ Monitors CPUFAN/ CHASFAN/ AUXFAN Speeds

¾ Monitors system Voltage

Infrared:

¾ Supports IrDA Version 1.0 SIR Protocol with a maximum baud rate of up to 115.2 Kbps

HD Audio Sound Codec Onboard:

¾ HD Audio (High Definition Audio) protocol compliance

¾ Compliant with Azalia specifications

¾ 8-channel playback capability

¾ Supports Sony/ Philips Digital Interfaces (S/PDIF)

LAN Controller:

¾ The PX915PC PRO-G and PX915GC PRO-G provide a LAN facility using a built-in Marvell®

MV8001 chipset which supports Ethernet 10/100/1000 Mbit/s connectivity.

¾ The PX915PC PRO and PX915GC PRO provide an additional LAN facility using a built-in VIA®

VT6105 chipset which supports Ethernet 10/100 Mbit/s network connectivity.

Onboard Video Graphic: (only for PX915GC series)

¾ Supports 2D Acceleration

3

PX915PC/ PX915GC Series

¾ Supports 3D Acceleration

¾ Supports Video Acceleration

¾ Micorsoft

®

DirectX compatible

¾ OpenGL driver available

I/O facilities:

¾ One multi-mode Parallel Port capable of supporting the following specifications:

1. Standard & Bi-direction Parallel Port

2. Enhanced Parallel Port (EPP)

3. Extended Capabilities Port (ECP)

¾ Contains one serial port, 16550 UART

¾ Contains one VGA port (PX915GC series only)

¾ Supports Infrared Data Transmissions using IrDA

¾ Supports PS/2 mice and PS/2 keyboards

¾ Supports 360 KB/720 KB/1.2 MB/1.44 MB/2.88 MB floppy disk drives

¾ Contains 1 Game header

BIOS:

¾ Phoenix-Award™ BIOS

¾ Supports APM1.2

¾ Supports ACPI2.0 power management

Watch Dog Timer:

¾ This mainboard contains a special feature called the “Watch Dog Timer” which is used to

detect when the system hangs during the POST stage due to certain BIOS configuration

problems. Once a problem is detected, the Watch Dog will reset the configurations and

reboot the system.

4

PX915PC/ PX915GC Series

Configuration

Layout of PX915PC PRO-G

5

PX915PC/ PX915GC Series

Layout of PX915PC PRO

6

PX915PC/ PX915GC Series

Layout of PX915PC

7

PX915PC/ PX915GC Series

Layout of PX915GC PRO-G

8

PX915PC/ PX915GC Series

Layout of PX915GC PRO

9

PX915PC/ PX915GC Series

Layout of PX915GC

10

PX915PC/ PX915GC Series

11

Hardware Installation

This section will assist you in quickly installing your system hardware. Wear a wrist ground strap before

handling components. Electrostatic discharge may damage the system’s components.

CPU Processor Installation

This mainboard supports Intel

®

Pentium

®

4 processors using a Socket 775. Before building your system,

we suggest you visit the Intel website and review the processor installation procedures.

http://www.intel.com

CPU Socket 775 Configuration Steps:

1. Locate the CPU socket 775 on your

mainboard and nudge the lever away from

the socket as shown. Then lift the lever to a

140-degree angle (A). Next, lift up the iron

cover (B).

2. There are 2 distinctive marks located

near the corners of the socket on the same

side as the lever as shown (C). Match these

marks with the marks on the CPU and

carefully lower the CPU down onto the

socket (D).

3. Replace the iron cover and then lower the

lever until it snaps back into position (E).

This will lock down the CPU (F).

4. Smear thermal grease on the top of the CPU. Lower the CPU fan

onto the CPU/CPU socket and secure it using the attachments or

screws provided on the fan. Finally, attach the fan power cable to

the CPUFAN adapter.

Attention: DO NOT touch the pins on the socket

(the pins are sensitive and can be

easily damaged). Also, make sure that you have completed all of the installation steps

before starting the system. Finally, double-check that the heatsink is properly installed

and make sure that the CPU fan power cable

is securely attached (cooling problems can

cause overheating, leading to damage to the CPU and other sensitive components).

A

B

D

C

F

E

PX915PC/ PX915GC Series

FAN Headers

Three power headers are available for the cooling fans. Cooling fans play an important role in

maintaining the ambient temperature in your system.

Attention: We strongly recommend that you use a CPU fan sink

with your CPU. You can attach the

power cable from the CPU fan

sink to the CPUFAN Header.

Memory Installation

These mainboards contain 4 memory slots which use 184-pin DDR SDRAM with a total memory capacity

of up to 4 GB. You must install unbuffered/non-ECC DDR-SDRAM DIMMs with either 256 MB, 512 MB, or

1 GB of memory. These modules must be either DDR400 (PC3200) or DDR333 (PC2700) SDRAM.

How to enable Dual-Channel DDR :

These mainboards provide Dual-Channel functionality for its DIMM slots. Enabling Dual-Channel can

significantly increase your data access rates. DIMM1 and DIMM2 share one channel, while DIMM3 and

Attention: We strongly recommend that You have to install modules in

same specification to achieve the best effects. (Same timing specifications

and same DDR speed) lest the failure of power-on or low memory speed if

you install modules in different type, different SPD (series presence

detect).

12

PX915PC/ PX915GC Series

DIMM4 share the second channel. Enabling Dual-Channel simply means to make sure that the total

memory for the two channels are balanced. For example: If you install one 256 MB module in DIMM1

and one in DIMM2 (256MB x 2 = 512MB), you must install a total of 512 MB between DIMM3 and DIMM4. In

balancing the memory on the two channels, you have, in effect, enabled Dual-Channel.

RAM Module Installation:

The following instructions explains memory module installation for these mainboards:

1. Pull the white plastic tabs at both ends of the slot away from the slot.

2. Match the notch on the RAM module with the corresponding pattern in the DIMM slot. This will

ensure that the module will be inserted with the proper orientation.

3. Lower the RAM module into the DIMM Slot and press firmly using both thumbs until the module snaps

into place.

4. Repeat steps 1, 2 & 3 for the remaining RAM modules.

＊ The pictures above are for reference only. Your actual

installation may vary slightly from the pictures.

Back

Panel

13

PX915PC/ PX915GC Series

Configuration

PS/2 Mouse & PS/2 Keyboard Connectors: KB/MS

These mainboards provide a standard PS/2 mouse connector and PS/2 keyboard connector. The pin

assignments are described below:

PS/2 Mouse

PS/2 Keyboard

Assignment

1 Data 4 +5 V (fused)

2 No connect 5 Clock

3 Ground 6 No connect

Serial and Parallel Interface Ports

These mainboards come equipped with one serial port and one parallel port. A VGA port is also

provided with the PX915GC series only.

Parallel Interface Port: PRT

The parallel port on your system has a 25-pin, DB25 connector that is used to interface with parallel

printers and other devices using a parallel interface.

The Serial Interface: COM1

The serial interface port is sometimes referred to as an RS-232 port or an asynchronous communication

port. Mice, modems and other peripheral serial devices can be connected to this port.

VGA Graphics Connector (PX915GC series only):

The PX915GC Series has a built in VGA port. Your VGA monitor can attach directly to this VGA

connector (D-SUB 15 pin).

14

PX915PC/ PX915GC Series

15

USB & (GB) LAN Connectors: USB/ LAN and

USB/ GBLAN (LAN and GBLAN are optional)

These mainboards come with 4 USB ports. The USB connectors are used to attach to keyboards, mice

and other USB devices. You can plug the USB devices directly into this connector. The PX915PC PRO-G

and PX915GC PRO-G have a 10/100/1000 Mbit/s LAN port. And the PX915PC PRO and PX915GC PRO

have an additional 10/100 Mbit/s LAN port. The LAN connectors can be attached directly to a network.

Audio Port Connectors: Sound

This mainboard comes equipped with 6 Audio Ports. The Mic-in, Line-in and Front Speaker-out are

standard audio ports that provide basic audio functionality. When you install the 8 Channel Audio

Effects driver (4/6/8 channel audio), the other 3 audio ports will be enabled (see appendix 1).

Line In (blue) Connects to an external audio device such as a CD player, tape player or other audio

devices that provide audio.

Front Speaker-Out (green) Connects to standard audio speakers for audio output. This port becomes

the surround sound front speakers when the 8 Channel Audio Effects (4/6/8 speakers) driver is

installed and enabled. Also note that this port provides the most amperage of all the ports making it

suitable for headphones and speakers without their own power cables.

Mic In (pink) Connects to a microphone.

Surround Back Speaker-out (black) This port represents the surround sound back speakers and is only

functional when the 4/ 6/ 8 Channel Audio Effects driver is installed and enabled.

Center/Subwoofer (orange) This port represents the Center/Subwoofer speakers and is only

functional when the 6/ 8 Channel Audio Effects driver is installed and enabled. Surround Speaker-out

(grey) This port represents an auxiliary port and is only functional when 8 Channel Audio Effects driver

is installed and enabled.

Con

Assignment

1 TX+ (TX+) 5 NC (TRD2-)

2 TX- (TX-) 6 RX- (RX-)

3 RX+ (RX+) 7 NC (TRD3+)

4 NC (TRD2+) 8 NC (TRD3-)

Assignment

1/5

+5 V (fused) 3/7

USBP0+/P1+

2/6

USBP0-/P1- 4/8

Ground

With these mainboards, you can turn your default 2-speaker audio system into a 4,

6, or 8 speaker audio system by installing the 8 Channel Audio Effects driver. See

appendix 1 for more information.

PX915PC/ PX915GC Series

16

nectors

Floppy Disk Connector: FDC

These mainboards provide a standard floppy disk connector (FDC) that supports 360K, 720K, 1.2M,

1.44M and 2.88M floppy diskette drives. This connector supports the floppy drive ribbon cables

provided in the packaging.

Hard Disk Connectors: IDE1/ SATA1-4

These mainboards provide a standard IDE connector that supports PIO Mode 0~4, Bus Master, Ultra ATA

66/100. 4 Serial ATA connectors are also available and can provide 150 MB/s transmission rates.

IDE1 (Primary IDE Connector)

You can connect 2 IDE devices to the IDE1 connector using a single ribbon cable with 3 connectors (2

for the drives and one to connect to the board). If you are connecting 1 drive, you should configure it

as the Master device. If you are connecting a second drive, you must configure it as the Slave device

(see your hard drive manual for master/slave configuration specifics). If you have an IDE CD-ROM drive,

you just can attach it to this connector.

SATA1-4 (Serial ATA connector)

These SATA connectors (SATA1 – SATA4) support Serial ATA 150. Each SATA connector can only support

one serial ATA device. Note: With most storage devices, there is a power cable that you need attach to

a power source (power supply).

Front Panel

Page is loading ...

Albatron PX915GC PRO User manual

This manual is also suitable for

Albatron PX915GC PRO User manual

Related papers

Other documents