Home Styles 5033-949 Assembly Instructions

Type
Assembly Instructions

This manual is also suitable for

Part List
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occurring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure
a completed product as it was designed.
88 5033 942
Kitchen Island
D.
Side Panel
1 pc.
E.
Side Panel
1 pc.
K.
Back Panel
2 pcs.
L.
Shelf
4 pcs.
M.
Shelf
1 pc.
P.
Base
1 pc.
U.
Door
1 pc.
T.
Door
1 pc.
For assembly also need carton 88 5033 941
M6x30
Head Cap Bolt
26 pcs. (+1 extra)
Cam Lock
16 pcs.(+2 extra)
Cam Lock Screw
16 pcs.(+1 extra)
Machine Screw
6 pcs.
Adjustable Pin
20 pcs. (+1 extra)
Small
Hex Wrench
1 pc.
Knob
2 pcs.
M3.5x16
Wood Screw (short)
for Drawer Base Part
6 pcs. (+1 extra)
M3.5x25
Wood Screw (long)
for Drawer Side Part
8 pcs. (+1 extra)
Pull Handle
2 pcs.
Hardware List
S.
Plinth
2 pcs.
H2.
Front Rail
1 pc.
M4x16
Wood Screw
for Hinge
27 pcs. (+2 extra)
Tools recommended for assembly : Level
Home Styles Consumer Assistance : www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Tools required for assembly : Phillips screwdriver
Hex Wrench
1 pc.
C.
Side Panel
1 pc.
B.
Side Panel
1 pc.
J.
Stretcher
1 pc.
H1.
Front Rail
1 pc.
I.
Back Stretcher
2 pcs.
R.
Leg Support
1 pc.
Q.
Plinth
2 pcs.
V.
Drawer
1 pc.
F.
Side Panel
1 pc.
N.
Back Support
1 pc.
G.
Side Panel
1 pc.
O.
Back Support
1 pc.
Assembly Instructions 2/6
STEP 1
IMPORTANT
* Do not tighten up all the screws until each part is properly assembled.
*You should keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
* After assembly, item must be level to work properly. Use the included adjustable levelers to level.
Attach Top (A1) to Top (A2) with
Wood Screws.
Put Cam Lock Screws into
the pre-drilled holes of Top (A1),
Side Panel (D), (E), (F), (G)
and tighten.
Cam Lock Screw
A1
D
E
F
G
A2
A1
Wood Screw
Cam Lock Screw
Assembly Instructions 3/6
STEP 2
STEP 3
D
E
B
P
Attach Side Panel (B) to Base (P) with
Head Cap Bolts.
Attach Side Panels (D) and (E) to
Base (P) with Head Cap Bolts.
H1
I
I
J
Attach Front Rail (H1) and
Front Rail (H2) to unit
using Cam Locks.
Attach Back Stretcher (I) to unit using
Cam Locks.
Slide Back Panel (K) into Place.
Attach Stretcher (J) to unit then slide Back Panel (K)
into place.
Head Cap Bolt
K
K
H2
Assembly Instructions 4/6
STEP 4
Attach Side Panel (C) to Base (P)
with Head Cap Bolts.
Attach Side Panels (F) and (G) to
unit with Head Cap Bolts.
P
F
G
C
Q
Q
R
S
S
P
STEP 5
Attach Plinths (Q) to Base (P)
with Head Cap Bolts.
Attach Plinths (S) and Leg Support (R)
to unit with Head Cap Bolts.
Head Cap Bolt
Cam Lock
Head Cap Bolt
Assembly Instructions 5/6
STEP 7
STEP 6
Attach Back Support (N) and (O)
to unit with Wood Screws into
pre-drilled holes.
O
N
A
Place Top (A) onto unit with Cam Locks.
Attach Doors (T) and (U) by sliding the door lift hinges into the side panels lift hinges.
(See Figure 1)
Attach Knobs to Doors (T) and (U) with Machine Screws.
(See Figure 2)
Insert Adjustable Pins into side panels at the desired level,
then place Shelves (L) and (M) into position.
Slide the Drawers (V) into position.
T
U
L
L
L
L
M
V
Figure 1
Figure 2
Adjustable Pin
Cam Lock
Wood Screw
(Figure 3)
To level the unit, adjust the adjustable levelers on the bottom of unit. (See Figure 3)
Note: Unit must be level to work properly.
V2
V3
V4
V5
V1
(Figure 3)
Assembly Instructions 6/6
Insert wood screws (6X)short
into the pre-drilled holes in V5,
tighten screws. (See Figure 3)
Attach hardware pulls with
machine screws.
(See Figure 4)
Slide V5 into the grooves in V3
and V4. Be sure to push V5 all
the way forward to it meets V1.
(See Figure 2)
STEP 4
Tighten all screws used in
drawer assembly.
(Figure 1)
(Figure 2)
MAKE SURE ROLLER
IS ON THE BACK
V2
V3
V4
V5
V1
Drawer
Part List
V1.
Front Part
1 pc.
V5.
Base Part
1 pc.
V2.
Back Part
1 pc.
V3.
Side Part
1 pc.
V4.
Side Part
1 pc.
(Figure 4)
STEP 1
STEP 2
STEP 3
Attach V1 to V3 and V4, using
a andPhillips screwdriver
wood screws (4X),long
tighten halfway.
Attach V2 to V3 and V4 using
wood screws (4X),long
tighten halfway. (See Figure 1)
V1
V2
V4
V3
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Home Styles 5033-949 Assembly Instructions

Type
Assembly Instructions
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI