Part List
Hardware List
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the wood parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Cam Lock Screw
28 pcs.(+1 extra)
88 5180 64
Arts & Crafts Pantry
Flat Washer
4 pcs. (+1 extra)
Hex Wrench
1 pc.
Small
Hex Wrench
1 pc.
Tools required for assembly : Tools recommended for assembly :Phillips screwdriver Level
Home Styles Consumer Assistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Knob
4 pcs.
Machine Screw
8 pcs.
Adjustable Pin
16 pcs. (+1 extra)
Wood Screw
for Back Panel
16 pcs. (+1 extra)
Cam Lock
28 pcs.(+1 extra)
S.
Door
1 pc.
D.
Bottom
1 pc.
N.
Top
1 pc.
Q.
Side Panel
1 pc.
H.
Door
1 pc.
U.
Back Post
1 pc.
T.
Back Panel
2 pcs.
O.
Front Rail
1 pc.
L.
Leg Frame
1 pc.
M.
Back Rail
4 pcs.
P.
Side Panel
1 pc.
K.
Leg Frame
1 pc.
C.
Shelf
4 pcs.
A.
Top
1 pc.
B.
Front Rail
1 pc.
E.
Side Panel
1 pc.
F.
Side Panel
1 pc.
G.
Door
1 pc.
R.
Door
1 pc.
I.
Back Panel
2 pcs.
J.
Back Post
1 pc.
Spring Washer
4 pcs. (+1 extra)
Head Cap Bolt
4 pcs. (+1 extra)
Assembly Instructions 2/5
IMPORTANT
* Do not tighten up all the screws until each part is properly assembled.
* You should keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
* After assembly, item must be level to work properly. Use the included adjustable levelers to level.
* Use a soft cloth between these parts and the floor.
Figure 1
STEP 1
Insert Cam Lock Screws into the pre-drilled holes of
Top (A), (N), Bottom (D) and Side Panel (E), (F), (P), (Q).
(see Figure 1)
A
D
Q
N
F
P
Cam Lock Screw
E
Assembly Instructions 3/5
B
E
F
L
K
Figure 2
Figure 3
STEP 2
Attach Back Rail (M) to Side
Panel (F) using a Cam Lock.
Attach Back Post (J) to Back
Rail (M). Slide Back Panels
(I) to the unit. Attach Back
Rail (M) to unit using a Cam
Lock. Attach Front Rail (B) to
unit using a Cam Lock.
Attach Side Panel (E) to the
unit using Cam Locks.
(see Figure 2)
D
STEP 3
Attach Leg Frames (K), (L) to the Bottom
with Head Cap Bolts, Spring Washers and Flat Washers.
(see Figure 3)
A
Flat Washer
Cam Lock
Cam Lock
I
M
J
I
M
Head Cap Bolt
Spring Washer
STEP 4
Attach unit from Step 2 to unit
from Step 3 using Cam Locks.
Place Top (A) onto unit using Cam
Locks.
Assembly Instructions 4/5
STEP 5
Attach Back Rail (M) to Side Panel (Q) using a Cam Lock. Attach Back Post (U) to Back Rail
(M). Slide Back Panels (T) to the unit. Attach Back Rail (M) to unit using a Cam Lock.
Attach Front Rail (O) to unit using a Cam Lock. Attach Side Panel (P) to the unit using Cam
Locks.
STEP 6
Place Top (N) onto unit using
Cam Locks.
STEP 7
Attach unit from Step 6 to unit from
Step 4 using Cam Locks.
Cam Lock
Cam Lock
Head Cap Bolt
P
Q
M
M
U
T
T
O
N
Assembly Instructions 5/5
Figure 7
STEP 9
Insert 16X Wood Screws from
the back of the unit. (see Figure 6)
Note: Please make sure unit is
level before tightening these
screws.
To level the unit, adjust the adjustable
levelers on the bottom of unit.
(see Figure 7)
Adjustable Pin
Figure 6
Figure 5
Figure 4
STEP 8
Insert Adjustable Pins into side panels at desired location.
Place Shelves (C) into position.
Attach Doors (G), (H), (R) and (S) to the side panels by
sliding the door lift hinges into the side panel lift hinges.
(see Figure 4)
Assemble Pull Handles to Door (G), (H), (R) and (S)
with Machine Screws. (see Figure 5)
C
Wood Screw
for Back Panel
C
C
S
C
H
R
G
-
1
-
2
-
3
-
4
-
5
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Home Styles 5760-101 Assembly Instructions
-
-
-
-
-
-
-
-
-
