L'ACCES A L'ESPACE
CISEAUXARTICULEES TELESCOPIQUESMATS TRACTEES
ISO 9001
PINGUELY HAULOTTE • LA PERONNIERE - BP 9 - 42152 L'HORME • Tél. +33 (0) 4 77 29 24 24 • Fax SAV +33 (0) 4 77 31 28 11
email [email protected] • Web www.haulotte.com
OPERATING AND MAINTENANCE
INSTRUCTIONS
SELF-PROPELLED LIFT
HA 20PX - HA 26PX
242 031 6110 - E 10.02 GB
Operating and maintenance instructions
i
Caution !
GENERAL
You have just taken delivery of your mobile elevating work platform
It will give you complete satisfaction if you follow the operating and maintenance
instructions exactly.
The purpose of this instruction manual is to help you in this.
We stress the importance:
• of complying with the safety instructions relating to the machine itself, its use
and its environment,
• of using it within the limits of its performances,
• of proper maintenance upon which its service life depends.
During and beyond the warranty period, our After-Sales Department is at your
disposal for any service you might need.
Contact in this case our Local Agent or our Factory After-Sales Department,
specifying the exact type of machine and its serial number.
When ordering consumables or spares, use this documentation, together with the
«Spares» catalogue so as to receive original parts, the only guarantee of
interchangeability and perfect operation.
This manual is supplied with the machine and is included on the delivery
note.
REMINDER:You are reminded that our machines comply with the provisions of
the «Machines Directive» 89/392/EEC of June 14th 1989 as
amended by the directives 91/368/EEC of June 21st 1991, 93/44/
EEC of June 14th 1993, 93/68/EEC of July 22nd 1993 and 89/336/
EEC of May 3rd 1989, directive 2000/14/CE and directive EMC/89/
336/CE.
The technical data contained
in this manual cannot involve
our responsibility and we
reserve the right to proceed
with improvements or
modifications without
amending this manual.
Operating and maintenance instructions
ii
Operation and Maintenance - HA20PX - HA26PX
i
CONTENTS
1 - GENERAL RECOMMENDATIONS - SAFETY............................................................ 1
1.1 - GENERAL WARNING ................................................................................................. 1
1.1.1 - Manual ..................................................................................................................................... 1
1.1.2 - Labels ...................................................................................................................................... 1
1.1.3 - Safety....................................................................................................................................... 1
1.2 - GENERAL SAFETY INSTRUCTIONS......................................................................... 2
1.2.1 - Operators................................................................................................................................. 2
1.2.2 - Environment............................................................................................................................. 2
1.2.3 - Using the machine ................................................................................................................... 2
1.3 - RESIDUAL RISKS....................................................................................................... 4
1.3.1 - Risks of jerky movements and tipping over ............................................................................. 4
1.3.2 - Electrical risk............................................................................................................................ 4
1.3.3 - Risk of explosion or burning..................................................................................................... 4
1.3.4 - Risks of collision ...................................................................................................................... 4
1.4 - INSPECTIONS ............................................................................................................ 5
1.4.1 - Periodic inspections ................................................................................................................. 5
1.4.2 - Examination of machine suitability........................................................................................... 5
1.4.3 - State of conservation ............................................................................................................... 5
1.5 - REPAIRS AND ADJUSTMENTS................................................................................. 6
1.6 - VERIFICATIONS WHEN RETURNING TO SERVICE................................................ 6
1.7 - BEAUFORT SCALE .................................................................................................... 6
2 - PRESENTATION ......................................................................................................... 7
2.1 - IDENTIFICATION ........................................................................................................ 7
2.2 - MAIN COMPONENTS................................................................................................. 8
2.3 - WORK AREA............................................................................................................... 9
2.3.1 - Work area, HA 20P.................................................................................................................. 9
2.3.2 - Work area, HA 26P.............................................................................................................. 10
2.4 - TECHNICAL CHARACTERISTICS ........................................................................... 11
Operation and Maintenance - HA20PX - HA26PX
ii
2.4.1 - HA 20PX technical characteristics ......................................................................................... 11
2.4.2 - HA 26PX technical characteristics. ........................................................................................ 12
2.5 - OVERALL DIMENSIONS...........................................................................................13
2.5.1 - HA 20PX overall dimensions.................................................................................................. 13
2.5.2 - HA 26PX overall dimensions.................................................................................................. 14
2.6 - LABELS......................................................................................................................15
2.6.1 - Common «yellow» labels ....................................................................................................... 15
2.6.2 - Common «orange» labels ...................................................................................................... 15
2.6.3 - Common «red» labels ............................................................................................................ 16
2.6.4 - Other common labels ............................................................................................................. 17
2.6.5 - Labels specific to models ....................................................................................................... 18
2.6.5.1 - For HA20PX machine ........................................................................................................................... 18
2.6.5.2 - For HA26PX machine ........................................................................................................................... 18
2.6.6 - Labels specific to Holand ....................................................................................................... 18
2.6.7 - Labels specific to Australia..................................................................................................... 19
2.6.8 - Option : organic hydraulic oil.................................................................................................. 19
2.6.9 - Built-in generator in option ..................................................................................................... 20
2.6.10 - References of the machine's labels ....................................................................................... 21
2.6.11 - Labels positioning................................................................................................................... 22
3 - OPERATING PRINCIPLE...........................................................................................23
3.1 - HYDRAULIC CIRCUIT...............................................................................................23
3.1.1 - Travel, slewing, arm lifting and boom raising movements...................................................... 23
3.1.2 - Telescoping, pendular, platform rotation, compensation and steering movements ............... 23
3.1.3 - Telescoping, boom raising, arm lifting and pendular cylinders............................................... 23
3.1.4 - Platform rotation..................................................................................................................... 23
3.1.5 - Compensation ........................................................................................................................ 23
3.1.6 - Travel (moving the machine).................................................................................................. 23
3.2 - ELECTRICAL CIRCUIT .............................................................................................24
3.2.1 - General................................................................................................................................... 24
3.2.2 - Automatic engine stop............................................................................................................ 24
3.2.3 - Platform load monitor ............................................................................................................. 24
3.2.4 - Checking the inclination ......................................................................................................... 24
3.2.5 - High travel speed ................................................................................................................... 24
3.2.6 - Hour counter........................................................................................................................... 25
Operation and Maintenance - HA20PX - HA26PX
iii
3.2.7 - Reach limitation (HA 26PX) ................................................................................................... 25
3.3 - EMERGENCY ASSISTANCE AND RESCUE ........................................................... 25
3.3.1 - Rescue................................................................................................................................... 25
3.3.2 - Emergency assistance........................................................................................................... 25
3.3.3 - Manual emergency assistance system .................................................................................. 26
4 - USING THE MACHINE .............................................................................................. 31
4.1 - OPERATING SAFETY DEVICES.............................................................................. 31
4.1.1 - Movement (control from the «platform» post) ........................................................................ 31
4.1.2 - Emergency or recovery procedure......................................................................................... 31
4.2 - OFFLOADING - LOADING - MOVEMENT - PRECAUTIONS................................... 32
4.2.1 - Offloading by lifting ................................................................................................................ 32
4.2.2 - Offloading with ramps ............................................................................................................ 33
4.2.3 - Loading .................................................................................................................................. 33
4.2.4 - Travel..................................................................................................................................... 34
4.2.5 - Filling the fuel tank................................................................................................................. 34
4.3 - OPERATIONS BEFORE FIRST PUTTING INTO SERVICE..................................... 35
4.3.1 - Familiarisation with the control stations ................................................................................. 35
4.3.1.1 - «Turret» control post............................................................................................................................. 35
4.3.1.2 - «Platform» control post......................................................................................................................... 36
4.3.2 - Checks before using the machine..........................................................................................37
4.3.2.1 - Movement zone .................................................................................................................................... 37
4.3.2.2 - General appearance ............................................................................................................................. 37
4.3.3 - Built-in generator (option) ...................................................................................................... 39
4.3.3.1 - Instructions ........................................................................................................................................... 39
4.4 - PUTTING INTO SERVICE......................................................................................... 40
4.4.1 - Operations from the ground................................................................................................... 40
4.4.1.1 - Starting the engine: Photo 4, page 35 .................................................................................................. 40
4.4.1.2 - Testing the movements (Photo 4, page 35).......................................................................................... 40
4.4.1.3 - Switching to «platform» control............................................................................................................. 40
4.4.2 - Operations from the platform ................................................................................................. 41
4.4.2.1 - Testing the control post ........................................................................................................................ 41
4.4.2.2 - Testing the movements ........................................................................................................................ 41
4.5 - EMERGENCY AND BACK-UP OPERATIONS ......................................................... 42
4.5.1 - Emergency assistance with the stand-by electropump unit................................................... 42
4.5.2 - Back-up.................................................................................................................................. 42
Operation and Maintenance - HA20PX - HA26PX
iv
4.5.3 - Uncoupling ............................................................................................................................. 43
5 - MAINTENANCE..........................................................................................................45
5.1 - GENERAL RECOMMENDATIONS............................................................................45
5.2 - MAINTENANCE SCHEDULE ....................................................................................46
5.2.1 - Consumables ......................................................................................................................... 46
5.2.2 - Maintenance diagram............................................................................................................. 47
5.3 - OPERATIONS............................................................................................................48
5.3.1 - Summary table ....................................................................................................................... 48
5.3.2 - Procedure............................................................................................................................... 49
5.3.2.1 - Hydraulic oil filter :................................................................................................................................. 49
5.3.2.2 - Drive wheel reducers ............................................................................................................................ 49
5.3.2.3 - Slew ring ............................................................................................................................................... 49
5.3.3 - List of consumables................................................................................................................ 50
6 - OPERATING FAULTS................................................................................................51
7 - SAFETY SYSTEM ......................................................................................................53
7.1 - FUNCTIONS OF THE TURRET CABINET FUSES AND RELAYS ...........................53
7.2 - FUNCTION OF THE SAFETY SWITCHES ...............................................................53
8 - ELECTRICAL DIAGRAM ...........................................................................................55
8.1 - E 448 DIAGRAM - SHEET 01/05...............................................................................55
8.2 - E 448 DIAGRAM - SHEET 02/05...............................................................................56
8.3 - E 448 DIAGRAM - SHEET 03/05...............................................................................57
8.4 - E 448 DIAGRAM - SHEET 04/05...............................................................................58
8.5 - E 448 DIAGRAM - SHEET 05/05...............................................................................59
8.6 - NOMENCLATURE .....................................................................................................60
9 - HYDRAULIC DIAGRAMS ..........................................................................................63
9.1 - HA 20PX / HA 26PX DIAGRAM - REFERENCE B15390..........................................63
9.2 - NOMENCLATURE, B15390 DIAGRAM.....................................................................64
Operating and maintenance instructions
1
Caution !
1 - GENERAL RECOMMENDATIONS - SAFETY
1.1 - GENERAL WARNING
1.1.1 - Manual
This manual is designed to familiarise the operator with HAULOTTE self-
propelled platforms in order to ensure efficient and safe use. However, it
cannot replace the basic training required by any user of site equipment.
The site manager is bound to inform the operators of the instructions
contained in the manual. He is also responsible for applying the «user
regulations» in force in the country of use.
Before using the machine, it is essential to understand all these instructions
in order to ensure safe and efficient operation.
This manual must be kept available for all operators. Additional copies can
be supplied by the manufacturer on request
1.1.2 - Labels
Potential dangers and machine instructions are indicated on labels and
plates. All instructions on such plates must be read.
All labels conform to the following colour code:
• Red indicates a potentially fatal danger.
• Orange indicates a danger of causing serious injury.
• Yellow indicates a danger that may cause material damage or slight
injury.
The site manager must ensure that these labels are in good condition and
remain legible. Additional copies can be supplied by the manufacturer on
request.
1.1.3 - Safety
Ensure that any persons entrusted with the machine are fit to meet the
safety requirements that its use imposes.
Avoid any working method that may jeopardise safety. Any use not
compliant with the instructions may cause risk and damage to persons and
property.
To attract the reader's attention
instructions are signalled by this
sign.
This manual must be kept by the user throughout the machine’s service
life, including in the case of loan, lease and resale.
Ensure that all plates or labels relative to safety and hazards are complete
and legible.
Operating and maintenance instructions
2
Caution !
1.2 - GENERAL SAFETY INSTRUCTIONS
1.2.1 - Operators
Operators must be aged over 18, and hold an operating permit issued by
their employer after undergoing a medical check and a practical test that
prove they are apt to operate the machine.
Only trained operators can use
Haulotte self-propelled platforms.
There must always be at least two operators present, so that one can
always:
• Take fast action if necessary.
• Take over the controls in case of accident or malfunction.
• Monitor and prevent movement of vehicles and people near the plat-
form.
• Guide the platform operator if required.
1.2.2 - Environment
Never use the machine:
• On ground that is soft, unstable, congested.
• On a ground that has a slope greater than permissible limit.
• In winds greater than the permissible limit. If used outside, use an an-
emometer to ensure that the wind speed does not exceed the permis-
sible limit.
• Near power lines (check minimum safe approach distances according
to voltage carried).
• In temperatures less than -15°C (especially in refrigerated chambers).
Consult us if it is necessary to work below -15°C.
• In explosive atmospheres.
• In poorly-ventilated areas, since the exhaust fumes are toxic.
• During storms (risk of lightning).
• In the dark, unless the optional floodlight is fitted.
• In the presence of intense electromagnetic fields (radar, moving and
high currents).
DRIVING ON PUBLIC ROADS IS PROHIBITED.
1.2.3 - Using the machine
In normal service (i.e. operating from the platform), the platform/turntable
control select key must be removed and kept at ground level by a person
who is present and trained in rescue/emergency assistance manoeuvres.
Do not use the machine:
• with a load greater than allowed load,
• if wind speed exceeds the maximum
• with more than maximum authorised number of occupants in platform,
• with a side load in the platform greater than permissible limit.
X km/h
Y km/h
Y>X
-15
0
˚C
Operating and maintenance instructions
3
Caution !
To reduce the risks of serious falls, operators must respect the
following instructions:
• Hold the guardrail firmly when lifting or driving the platform.
• Remove any traces of oil or grease from the platform steps, floor or
guardrails.
• Wear personal protective equipment suited to working conditions and
conform to local regulations, particularly when working in hazardous
areas.
• Never disable the limit switches of the safety devices.
• Avoid contact with stationary or moving obstacles.
• Do not increase the platform operating height by means of ladders or
other accessories.
• Never use the guardrails to climb into or out of the platform (use the
steps provided).
• Never climb on the guardrails when the platform is up.
• Avoid driving the machine at high speed in narrow or congested are-
as.
• Never use the machine without putting in place the platform safety bar
or closing the safety gate.
• Never climb on the covers.
Never use the platform as a crane,
hoist or lift.
Never use the machine to pull or
tow.
Never use the boom as a ram or
thruster or to lift the wheels.
To reduce the risks of tipping over, operators must follow these
instructions:
• Never disable the limit switches of the safety devices.
• Never move the control handles from one direction to the other with-
out stopping in the «O» position. (To stop when travelling, gradually
move the handle to «O», keeping your foot down on the pedal.).
• Do not exceed the maximum load or the number of occupants allowed
in the platform.
• Spread the load and if possible place in the centre of the platform.
• Check that the ground resists the pressure and load per wheel.
• Avoid contact with stationary or moving obstacles.
• Do not drive the platform at high speed in narrow or congested areas.
• Do not drive the platform in reverse gear (poor visibility).
• Do not use the machine with a congested platform.
• Do not use the machine with equipment or objects hanging from the
guardrails or boom.
• Do not use the machine with items liable to increase the wind load
(e.g. panels).
• Never carry out maintenance on the machine with the platform raised,
without first installing the required safety provisions (overhead crane,
crane).
• Perform the daily checks and monitor the machine’s good working or-
der during periods of use.
• Preserve the machine from any uncontrolled intervention when it is
not in operation.
NOTE : Do not tow the platform. (It has not been designed for towing
and must be transported on a trailer).
Operating and maintenance instructions
4
Caution !
Caution !
1.3 - RESIDUAL RISKS
1.3.1 - Risks of jerky movements and tipping over
The direction of travel can be
reversed after a 180° turntable
rotation. Take account of the colour
of the arrows on the chassis
compared with the direction of
travel (green = forward, red =
reverse)
Thus, moving the manipulator in the
direction of the green arrow on the
control panel will move the machine
according to the direction indicated
by the green arrow on the chassis.
Similarly, moving a manipulator in
the direction of the red arrow on the
control panel, will move the
machine in the direction of the red
arrow on the chassis
Risks of jerky movement and tipping over are high in the following
situations:
- Sudden action on the controls.
- Overloading of the platform.
- Uneven ground (Be careful during thaw periods in winter).
- Gusts of wind.
- Contact with an obstacle on the ground or at a height.
- Working on platforms, pavements, etc.
Allow sufficient stopping distances:
- 3 meters at high speed,
- 1 meter at low speed.
Allow sufficient stopping distances: 3 metres at high speed and 1 metre at
low speed.
Do not alter or neutralise any components connected in any way to the
machine’s safety or stability.
Do not place or fasten a load so that it overhangs the machine’s parts.
Do not touch adjacent structures with the elevator arm.
1.3.2 - Electrical risk
If the machine has a 220 V 16A max.
plug, the extension must be
connected to a mains socket
protected by a 30 mA differential
circuit breaker.
Electrical risks are high in the following situations:
- Contact with a live line (check safety distances before operation
near electricity lines).
- Use during storms.
1.3.3 - Risk of explosion or burning
The risks of explosion or burning are high in the following situations:
- Working in explosive or inflammable atmosphere.
- Filling the fuel tank near naked flames.
- Contact with the hot parts of the motor.
- Use of a machine generating hydraulic leakage.
1.3.4 - Risks of collision
- Risk of crushing people in the machine operation zone (when
travelling or manoeuvring equipment).
- The operator must assess the risks above him before using the
machine.
- Pay attention to the position of the arms during turntable rotation.
- Adapt movement speed to conditions related to the ground, traffic,
slope and movement of people, or any other factor that may cause
a collision.
- When driving down the ramp of a truck, ensure sufficient space is
available for safe unloading.
- Check brake pad wear regularly to avoid all risk of collision.
Operating and maintenance instructions
5
1.4 - INSPECTIONS
Comply with the national regulations in force in the country of machine use.
For FRANCE: Order dated 9 June 1993 + circular DRT 93 dated 22
September 1993 which specify:
1.4.1 - Periodic inspections
The machine must be inspected every 6 months in order to detect any
defects liable to cause an accident.
These inspections are performed by an organisation or personnel specially
designated by the site manager and under his responsibility (whether or not
they belong to the company) Articles R 233-5 and R 233-11 of the French
Labour Code.
The results of these inspections are recorded in a safety register kept by
the site manager and constantly available to the labour inspector and the
site safety committee (if one exists) and the list of specially designated
personnel (Article R 233-5 of the French Labour Code).
Moreover, before each use, check the following:
• the operator’s manual is in the storage compartment on the platform,
• the stickers are placed according to the section concerning "Labels
and their positions",
• oil level and any elements in the mainteance operation table
• look out for any danaged, incorrectly installed, modified or missing
parts.
NOTE : This register can be obtained from trade organisations, and in
some cases from the OPPBTP or private prevention agen-
cies.
The designated persons must be experienced in risk prevention (Articles R
233-11 or order n° 93-41).
No member of personnel is allowed to perform any check whatsoever
during machine operation (Article R 233-11 of the French Labour Code).
1.4.2 - Examination of machine suitability
The manager of the site where the machine is operated must ensure the
machine is suitable, i.e. capable of performing the work in complete safety,
and in compliance with the operating manual. Furthermore, the French
order of 9 June 1993 addresses problems relative to leasing, examination
of the state of conservation, checking upon operation after repairs, and test
conditions (static test coefficient 1.25; dynamic test coefficient 1.1). All
users must consult this order’s requirements and comply with them.
1.4.3 - State of conservation
Detect any deterioration liable to cause hazardous situations (concerning
safety devices, load limiters, tilt sensor, cylinder leaks, deformation, welds,
bolt tightness, hoses, electrical connections, tyre state, excessive
mechanical gaps).
NOTE : If the machine is rented/leased, the user responsible for the
machine must examine its state of conservation and suitabili-
ty. He must obtain assurance from the leaser that general pe-
riodic inspections and pre-operation inspections have been
performed.
Operating and maintenance instructions
6
Caution !
1.5 - REPAIRS AND ADJUSTMENTS
These cover major repairs, and work on or adjustments to safety systems
or devices (of a mechanical, hydraulic or electrical nature).
These must be performed by personnel from or working for PINGUELY-
HAULOTTE who will use only original parts.
Any modification not controlled by PINGUELY-HAULOTTE is
unauthorised.
The manufacturer cannot be held responsible if non-original parts are used
or if the work specified above is not performed by PINGUELY-HAULOTTE-
approved personnel.
1.6 - VERIFICATIONS WHEN RETURNING TO SERVICE
To be performed after:
• extensive disassembly-reassembly operation,
• repair affecting the essential components of the machine,
• any accident caused by the failure of an essential component.
It is necessary to perform a suitability examination, a state of conservation
examination, a static test, a dynamic test (see coefficient in paragraph (see
Chap 1.4.2, page 5).
These test must be performed by a
competent person.
1.7 - BEAUFORT SCALE
The Beaufort Scale of wind force is accepted internationally and is used
when communicating weather conditions. It consists of number 0 - 17, each
representing a certain strength or velocity of wind at 10m (33 ft) above
ground level in the open.
Description of Wind Specifications for use on land MPH m/s
0 Calm Calm; smoke rises vertically 0-1 0-0.2
1 Light Air Direction of wind shown by smoke 1-5 0.3-1.5
2 Light Breeze Wind felt on face; leaves rustle; ordinary vanes moved by
wind
6-11 1.6-3.3
3 Gentle Breeze Leaves and small twigs in constant motion; wind extends
light flag
12-19 3.4-5.4
4 Moderate Breeze Raises dust and loose paper; small Branches are moved 20-28 5.5-7.9
5 Fresh Breeze Small trees in leaf begin to sway; crested wavelets form
on inland waterways
29-38 8.0-10.7
6 Strong Breeze Large branches in motion; whistling heard in telephone
wires; umbrellas used with difficulty
39-49 10.8-
13.8
7 Near Gale Whole trees in motion; inconvenience felt when walking
against wind
50-61 13.9-
17.1
8 Gale Breaks twigs off trees; generally impedes progress 62-74 17.2-
20.7
9 Strong Gale Slight structural damage occurs (chimney pots and slates
removed)
75-88 20.8-
24.4
Operation and Maintenance - HA20PX - HA26PX
7
2 - PRESENTATION
HA 20PX and HA 26PX self-propelled lifts are designed for any high work
within the limit of their characteristics (see Chapter 2.4, page 11) and
complying with all the safety instructions particular to the machine and to
the locations where it is used.
The main operating post is in the «basket».
The turret operating post is an emergency or back-up post.
2.1 - IDENTIFICATION
A plate (Fig 1, page 7), fixed on the back right of the chassis, bears all the
indications (engraved) enabling the machine to be identified.
Fig. 1 - Name plate
REMINDER:Whenever requesting information, intervention or spares,
specify the type and serial number.
Operation and Maintenance - HA20PX - HA26PX
8
2.2 - MAIN COMPONENTS
Fig. 2 - Location of main components
01 - Rolling chassis
02 - Front steered and drive wheels
03 - Rear steered and drive wheels
04 - Pendular
05 - Platform support with load limiter
06 - Platform
07 - «Basket» control panel
08 - Compensation input cylinder
09 - 2-piece boom
10 - Slewing ring
11 - Turret
12 - Hoods
13 - Boom support
14 - Hydraulic travel motors and reducer
15 - Hydraulic travel motors and reducer
16 - Right compartment (hydraulic and diesel tanks,
control panel)
17 - Arm
18 - Tie rod
19 - Left compartment (engine + pump + starting
battery)
20 - Bottom counterweight (HA 26PX)
21 - Top counterweight
22 - Lifting and fixing lugs
54153101202 14 6
19
78917
16
11121813 21
22
Operation and Maintenance - HA20PX - HA26PX
9
2.3 - WORK AREA
2.3.1 - Work area, HA 20P
21
20
19
18
17
16
15
14
13
12
11
10
3
2
1
0
9
8
7
6
5
4
-4 -3 -2 0-1 1413121110987654321
Operation and Maintenance - HA20PX - HA26PX
10
2.3.2 - Work area, HA 26P
21
22
20
19
-4 -3 -2 0
26
25
24
-1
23
18
17
16
15
14
13
12
11
10
3
2
1
0
9
8
7
6
5
4
1413121110987654321 15 16
Operation and Maintenance - HA20PX - HA26PX
11
2.4 - TECHNICAL CHARACTERISTICS
2.4.1 - HA 20PX technical characteristics
DESIGNATIONS HA 20PX
Load 250 kg, including 2 peoples
Maximum lateral manual force 40 kg
Max. wind speed 60 km/h
Floor height 18,65 m
Working height 20,65 m
Overall length 9,00 m
Overall width 2,35 m
Overall height 2,67 m
Wheelbase 2,60 m
Ground clearance 420 mm
max. reach 13,50 m
Boom range 0° + 75°
Telescoping (stroke) 4200 mm
Turret rotation Continuous
Max. force on wheel 6194 daN
Reducer (efficiency = 95%) 30
Max. travel slope 40%
Tyre sizes 15 - R22
Outside turning radius 3,9 m
Tilt - Monitor 5° (≈ 9%)
Hydraulic reservoir 150 litres
Diesel tank 150 litres
Total weight 12 260 kg
Number of drive wheels 4
Number of steered wheels 4
Differential lock YES
Hydraulic brakes YES
Freewheeling YES
Wheel nut tightening torque 32 mdaN
Slewing ring nuts tightening torque 27 mdaN
Vibration level at feet < 0,5/s2
Vibration level at hands < 2,5/s2
DEUTZ diesel engine
Power
Idling power output
Consumption
Idling consumption
F4L 1011 F
51.6 HP / 38 kW at 2400 rpm
20.4 HP / 15 kW at 1250 rpm
230 g/kWh
230 g/kWh
45 cm3/rev LOADSENSING hydraulic pump 85 l/min max.
Hydraulic pressure:
General
Travel
Steering
Slewing
Equipment
240 bar
240 bar
240 bar
100 bar
240 bar
Travel speed
(proportional)
LS: 1.2 km/h
HS: 4.5 km/h
max. ground pressure with 250 kg
-hard ground (concrete)
-loose ground (mud)
14,0 daN/cm2
4,3 daN/cm2
Starting battery 1 X 12 V - 95 Ah
Supply voltage 12 V
Acoustic power 108 dB (A)
Noise level at 10 meters 73.9 dB (A)
Operation and Maintenance - HA20PX - HA26PX
12
2.4.2 - HA 26PX technical characteristics.
DESIGNATIONS HA 26PX
Load 230 kg, including 2 peoples
Maximum lateral manual force 40 kg
Max. wind speed 45 km/k
Floor height 24,00 m
Working height 26,00 m
Overall length 11,90 m
Overall width 2,35 m
Overall height 2,67 m
Wheelbase 2,60 m
Ground clearance 420 mm
max. reach 14,6 m
Boom range 0° + 75°
Telescoping (stroke) 6915 mm
Turret rotation Continuous
Reducer (efficiency = 95%) 30
Max. travel slope 40%
Tyre sizes 15 - R22
Outside turning radius 3,9 m
Tilt - Monitor 3°
Hydraulic reservoir 150 litres
Diesel tank 150 litres
Total weight 14 150 kg
Number of drive wheels 4
Number of steered wheels 4
Differential lock YES
Hydraulic brakes YES
Freewheeling YES
Wheel nut tightening torque 32 mdaN
Slewing ring nuts tightening torque 27 mdaN
Vibration level at feet < 0,5/s²
Vibration level at hands < 2,5/s²
DEUTZ diesel engine
Power
Idling power output
Consumption
Idling consumption
F4L 1011 F
51.6 HP / 38 kW at 2400 rpm
20.4 HP / 15 kW at 1250 rpm
230 g/kWh
230 g/kWh
45 cm3/rev LOADSENSING hydraulic pump 85 l/min max.
Hydraulic pressure:
General
Travel
Steering
Slewing
Equipment
240 bar
240 bar
240 bar
100 bar
240 bar
Travel speed
(proportional)
LS: 1.2 km/h
HS: 4.5 km/h
max. ground pressure with 250 kg
-hard ground (concrete)
-loose ground (mud)
16,0 daN/cm2
4,6 daN/cm2
Max. force on wheel 6970 daN
Starting battery 1 X 12 V - 95 Ah
Supply voltage 12 V
Acoustic power 108 dB (A)
Noise level at 10 meters 73.9 dB (A)
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
